Question about 1999 Volkswagen Passat

1 Answer

WINDOW WINDER REPLACMENT

HOW TO REMOVE OLD WINDOW WINDER FROM PASSANGER FRONT DOOR ON VW PASSAT1998 ELECTRIC WINDOWS

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 337 Answers

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the inner door panel 1990 dodge dynasty


Remove handle ,window winder if not electric,remove arm rest screws prize door trim off carefully using a flat blade or screw driver.window winder is held on with a horse shoe clip which can be removed with a piece of wire with a hook in the end.

Oct 04, 2015 | Dodge Cars & Trucks

2 Answers

Passanger window wont roll up from driver side or passanger side


Replace the regulator. It comes with the motor. You have to remove the door panel to access it.

May 26, 2015 | 2006 Kia Sorento

1 Answer

My auto window's will not lock. Horn blow's if all in back and passangers windows are locked manually. I can lock the drivers side if the passanger side winder is unlocked. Can you help me?


Have it scanned to read the codes in the Komfort/Secuity controller (ECU) A dealer or independent shop can do this.

There are micro switches in the door locks that fail.

As far as rear passenger problem...remove the lower rear seat bolster and check for wire/s being crushed between the seat frame and floor pan.

Oct 29, 2013 | 1999 Volkswagen Cabrio

1 Answer

The passenger's power window in the front,it doesn't work....Everytime I replace a new power window fuse, it burns ....why?....... Honda Civic 2002


If the window is jammed or there is short in the electrical supply to the motor winder then so much current will be drawn that the fuse will burn out. The only way to assess what is going on is to access the mechanism by removing the inner door panel. Try assisting with your hands the opening and shutting of the window. If it is very stiff to move try cleaning the window surround channels with an old tooth and detergent.

Jul 18, 2010 | 2002 Honda Civic

1 Answer

How do I install a new front door RH window? My parents front passenger side window was damaged. I can obtain one however, I need to install it and remove the broken glass that has fallen inside of the...


you will have to remove all the trim from inside of the door, remove the weather seal from behind the trim as well
if it has electric windows you will have to remove the winder as a unit from inside the door
remove any broken glass from inside the door, turn the replacement glass with the narrow end down and slide it down through the top opening where the window glass normally goes in the door
once it is inside the door turn it around so it is in its normal position and place it in the channels where the glass runs, connect the electric winder mechanism and replace everything in reverse order as you removed it
hope this helps

Jul 08, 2010 | 2005 Toyota Matrix

2 Answers

How do i fix a electric window winder motor in my car


First you will have to remove the door panel to access the window motor which is located in the door. in most cases you are better off to replace it. but first you need to check for power at motor if it has power and doesn't work replace it if no power check the switch then check wire in the door jam they usually break from excessive opening and closing of the door .

Jan 06, 2010 | Ford Focus Cars & Trucks

1 Answer

Removing rear passanger door panel on 1993 toyota camary wagon


mmmm from what i can recall 2 screws in arm rest (two small holes underneath arm rest hides the screws)take these out also one in door handle trim behind handle, And the window winder if you look close in the gap between window winder and door trim you should be able to see a curbed metal pin this holds winder in place so to remove it get a knife ( thin blade will fit in between winder and trim) and push on the end bit of the metal pin and it should spring off and then door handle can be removed. After this run your hands around door trim gently pulling around all edges ect this will pull door trim away from supports

Jun 05, 2009 | 1998 Toyota Camry

1 Answer

Remove drivers side window motor


remove the door trim from the inside of the door, now remove the door plastic weather protector which should expose the window glass and also the electric motor and winder mechanism.
There will be a plastic wire connector inside the door which will have to be disconnected to remove the electric motor etc.
Hope this helps

May 19, 2009 | 1994 Pontiac Grand Am

1 Answer

Replace the power window motor


First door panel has to be removed, If i remember correctly there are 3 or 4 rivets that have to be drilled out to remove motor from window regulator, and unplug electrical connection, and it should come out. Replacement motor will have new blots and nuts to secure new motor back on to regulator.

Mar 04, 2009 | 1993 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
1999 Volkswagen Passat Logo

Related Topics:

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

61249 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...