Question about 2001 Chevrolet Silverado 1500

1 Answer

02 Trailblazer will not go in reverse, but will go in drive

I can put the shifter into reverse, but when I hit the gas pedal nothing happens. If I put it in drive, I can go forward no problem. Any ideas?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

You probably have to reset the ecu!

Posted on Dec 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I press on the gas pedal on my 2007 Kia optima and nothing happens. The engine is running


If you have drive by wire, It could be the TPS/gas pedal sensor or the vehicle is in limp mode. Have the codes read. If it is cable driven, the cable has popped off the throttle or the cable broke.

Dec 20, 2015 | 2007 Kia Optima

1 Answer

I have an 02 chevy trailblazer gear shifter will move but car won't move in reverse or drive now service 4 wheel drive light is on and the switch nuetral is lighting up but its on 2 wheel drive


May be broken 4WD actuator (quite common) which has stuck between engaged and disengaged. Remove and inspect actuator, but first examine all linkage for damage or having come loose.

Dec 19, 2014 | 2002 Chevrolet TrailBlazer

1 Answer

I hit the gas pedal and the car does nothing


IT SOUNDS LIKE THE THROTEL CABLE. HAVE SOMEONE SMASH THE GAS PEDAL WILE YOU LOOK UNDER THE HOOD WHERE YOU WAS WORKING YOU SHOULD SEE IT MOVING. IT SNAPS BACK ON THEY MIGHT HAVE A COVER ON THE END THAT SLIDES BACK BEFOR SNAPING IT BACK ON

Nov 30, 2013 | 2012 Nissan Altima 2.5 Sedan 2.5L 4-cyl....

1 Answer

2007 chevy trailblazer in Neutral and shifter won't unlock


the btsi solenoid is probably went out of it, you can remove the shifter boot and pop the linkage off of it and get it to shift had to do this to mine before

Jan 17, 2013 | 2007 Chevrolet Trailblazer

1 Answer

My Sable will turn on fine but when i try shifting the gear they won't go in the shifter just glides along and the car remains idle. The day it started doing this it made a loud screeching noise and...


If the shifter moves but does not feel like it is trying to put car in gear the cable that goes from the shifter to the transmition could have broke or came loose. If that happened while driving the gears may have tried to shift when tension was released from the cable.

May 10, 2011 | 1999 Mercury Sable

1 Answer

When driving, if I hit the gas it makes like a high pitch whining sound. The hrder you hit the gas the louder the sound. You can hear it in idle. It only makes the sound while applying the gas pedal,...


Hello my name is Israel and I will try to help. The problem sounds as if it could be the tension pulley. This is the pully that puts tension on the belt. It may be going out. Yes I know that your vehicle is only 5 years old but it could happen. I just had mine replaced and it was only 3 years old. Good Luck.

Mar 22, 2011 | 2006 Chevrolet Trailblazer

1 Answer

The gear is getting stuck... i press on brakes and when car is in park it is hard to put on reverse.. the car runs great...


In all probability the brake sensor on the pedal is starting to work erratically. This sensor sends a signal to the shifter gate, and the gate will not open unless the brake pedal is depressed. I had it happen to me, and the only solution until i replaced the sensor was to hit the brake over and over until the stop light worked (You can check it while looking at the 3rd stop light in the rear view mirror). If the stop lights work, the shifter gate should allow the shifter to move out of park. This sensor/ switch is located about 3 inches above the brake pedal, and it is easily recognizable by the cable attached to it.

Aug 31, 2010 | 2002 Honda Accord

1 Answer

My accord won't go in reverse what are my options


n all probability the brake sensor on the pedal is starting to work erratically. This sensor sends a signal to the shifter gate, and the gate will not open unless the brake pedal is depressed. I had it happen to me, and the only solution until i replaced the sensor was to hit the brake over and over until the stop light worked. If the stop lights work, the shifter gate should allow the shifter to move out of park. This sensor/ switch is located about 3 inches above the brake pedal, and it is easily recognizable by the cable attached to it.

Feb 17, 2010 | 1998 Honda Accord

1 Answer

2003 Ford Ranger Pickup traveling down the road


Is there somthing hitting the gas pedal, like the floor mat? Or maybe something under the dash came loose and is getting caught under the brake pedal and pushing on the gas. Put the shifter in neutral if you get into a situation where going to hit something or someone. The engine has a rev limiter, to prevent it from over reving.

Feb 10, 2010 | 2003 Ford Ranger Regular Cab

1 Answer

My 02 trailblazer the shifter will not lock and key will not come out of the ignition what do i do?


sounds like a broken shifter cable from shifter to brake pedal make sure it is releasing properly and also moving in and out

Jan 28, 2010 | 2002 Chevrolet TrailBlazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...