Question about 1992 Chevrolet Cavalier

1 Answer

1992 chevy cavalier, 4 cyl. crank system sensor

I need to replace the crank system sensor, but i cannot find it's location on the engine, please show me on a diagram or exact instruction on the location, i have been looking for 2 days trying to find the location so i can fix it, i already have a new one to replace it with.
thanks, marianne

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

The crank sensor is under the oil sending unit on the back of the motor next to the firewall. It is held in the block by an 8mm bolt. It has to be removed from under the car. Get under the car on the RH side and get back far enough that you can see over the transaxle. Good Luck.

Posted on Jan 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where would i get a diagram to show me where the crank sensor on my 1997 town and country van is


The crank sensor will be located on the back of that engine. By the starter. YouTube has a cool video about it.

Oct 03, 2014 | 1997 Chrysler Town & Country

1 Answer

Where is the 2nd crank shaft sensor located, and is there a diagram to show where these sensors are located?


is it a no crank or crank no start?
Possible causes for code P0335
- Faulty crankshaft position sensor
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery

Read more: http://engine-codes.com/p0335.html#ixzz3Cxw6SN6O

Sep 10, 2014 | 2004 Buick Rendezvous

1 Answer

Engine will just keep cranking,stutter at times even die while driving, have replaced fuel pump, o2 sensors, now have found its more than likely crankshaft position sensor, I'm not sure where it is...


Quite often the crank angle sensor is located at the front of the engine down near the bottom pulley that sits on the end of the crank. You should see (under the grime :) ) a small sensor with a pigtail leading to wiring harness. This should be your crank angle sensor.
It might be far easier to get your vehicle checked either via a diagnostic or sometimes you can put a loop back wire in to generate basic codes. This of course depends upon the system OBD or OBDII
Then you read the codes which are usually the amount of times the engine check light blinks or similar and you then check that code against a code list. Most good workshop manuals will have code lists and information on how to check your codes.

Aug 01, 2011 | Jeep Grand Cherokee Cars & Trucks

2 Answers

Is it possible to get a diagram of the crank sensor for the 2004 hyundai sonata


Hi, in both engines the crank sensor is at the back of the engine by the transmission. The sensor is #10 in the diagram below and looks like the picture included.
jturcotte_1640.gif

4-cylinder crank sensor:
jturcotte_487.jpg

6-cylinder crank sensor:
jturcotte_488.jpg

May 06, 2011 | Hyundai Motor 2004 Sonata

1 Answer

Engine diagram showing location of crank sensor on 2004 lincoln ls v8


Hello cmalstrom.

The sensor is mounted to the right of the harmonic balancer at the front of the engine.
On the diagram below look to the left about 3/4 of the way down.
I apologize for the size, we are limited here for amount of room.
If you need more help with this please ask me.
Thank you for using FixYa.

KL

kiltylake_146.gif

Jan 15, 2011 | 2004 Lincoln LS

1 Answer

Where can I find the crank position sensor on a 1999 Intrigue 3.5.engine H?


The crank sensor is located on the leftside of engine at the base of oil level indicator, heres a diagram to show you, the diagram show it with engine upside down,the sensor is near the bottom of the block right above the top of oil pan,remove a bolt and it slides out.a39ea9d.gif

Aug 24, 2010 | 1999 Oldsmobile Intrigue

1 Answer

Need to replace external crank position censor - need schematic


Hello tsutor, my name is JShreader. Thank you for choosing fixya.com.

There are 2 on this Engine. I uploaded a .pdf with pictures showing both of their locations. You can download it by clicking HERE. I hope this helps you. If you have any more questions or need any more diagrams, please don't hesitate to ask...Thanks again, JShreader!

Mar 30, 2009 | 1998 Chevrolet Lumina

2 Answers

Car won't start


this is located on different spots on different engines if you go to autozone or napa get the price of the crank sensor they can give you a diagram of the exact location of where yours is

Jan 25, 2009 | 1997 Dodge Intrepid

Not finding what you are looking for?
1992 Chevrolet Cavalier Logo

535 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

63291 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...