Question about 2003 Ford Explorer Sport Trac

1 Answer

Blinker not working;Engine dies not ideling properly

The bliker does not work. I hanged all the fuses, but the blinker still does not work.

Also the engine dies and will not idle properly. Have to rev engine up to 2000 RPM to keep it running at red lights.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 66 Answers

Ck voltage from alt

Posted on Dec 17, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Vauxhall mariva blikers left hand side aint working bolbs good fuses good dashboard blinker light s


www reliable-store com
It helps you repair your vehicle easily without more help. Ask the girl in chat at the bottom of the page

Jan 19, 2018 | Vauxhall Cars & Trucks

1 Answer

Passenger side, front blinker and back blinker and brake light doesn't work. do i just replace bulbs or look elsewhere, and where?


Year? model? grab the hazard switch knob and try to move it about with the blikers on and see if you can get it to start blinking, you may need a new turn signal switch.

Nov 23, 2010 | Chevrolet Impala Cars & Trucks

1 Answer

Signals and hazard lights not working, the fuse is good,thanks


sound like your bliker switch is bad , they are in your fuse box usually the big round looking thing , if you pull it , it will say blinker on it, they vary around $ 5 or 10 dollars

Aug 16, 2010 | 1999 Jeep Grand Cherokee

1 Answer

Right blinker works, but left one doesn't work at


either check for voltage at the blinker and also check for left blinker fuse . NO voltage at connector there is an open in wire replace try to find the open torn insulator or wire being exposed.

Jul 02, 2010 | 1997 Mitsubishi Eclipse

1 Answer

1999 ford explorer blikers wont work


Well your not going to like this but I think I can help im assuming you checked all the fuses inside the car and under the hood ? if there all good your problem more than likley is in the BCM as it controls the lights and blikers BCM stands for Body Control Module. good luck :)

Feb 18, 2010 | 1999 Ford Explorer

1 Answer

TURN SIGNAL, BRAKE & HAZARD LIGHTS


No Turn Signal Operation (blinker)The turn signal lights in your car are a basic electrical system that controls the front and rear blinker lights to alert the intended direction of the vehicle. We have listed some of the most common problems and repair troubleshooting tips below:
Troubleshooting Procedure
To start troubleshooting this problem:
  • Turn the key to the on position (do not start engine)
  • Inspect the system fuse located in the fuse panel and replace if needed. If you cannot find the location of the blinker fuse consult your owner's manual or an online repair manual
  • When a blinker flasher fails it can cause blinker lights to say on, not blink, or not go on at all. To test the blinker system flasher, remove the flasher unit and insert a jumper wire between the two terminals. If blinker stays on in both directions without blinking, replace the flasher. If you cannot find the location of the blinker flasher consult your owners manual or an online repair manual.
  • 1b7f814.jpg

Jul 09, 2009 | 1999 GMC Denali

1 Answer

BLINKERS ON 2004 JEEP WRANGLER NOT WORKING PROPERLY


The problem could be the wiring connecting to the lights, you need to check them for bare wires. Look them through for any metal hanging out of the rubber insulation. You may need to get new wiring.

Dec 04, 2008 | 1988 Jeep Wrangler

Not finding what you are looking for?
2003 Ford Explorer Sport Trac Logo

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

83096 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

gerry bissi

Level 3 Expert

4387 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...