Question about 1994 Chevrolet C1500

1 Answer

Trying to remove heater blower , but cant get the housing unit off?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 51 Answers

If there is something on the fenderwell thats in the way remove it to if not then rotate the motor housing until it comes out. I know its tight but it will come out. hope this helps please rate me

Posted on Jan 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace a heater core


Heater Core Removal & Installation Front To Remove:
  1. Make sure you have the anti-theft codes for the audio and the navigation system, and then write down the audio presets.
  2. Disconnect the negative cable from the battery.
  3. From under the hood, disconnect the heater valve cable from the heater valve. Turn the heater valve arm to the fully opened position.
  4. When the engine is cool, drain the engine coolant from the radiator.
  5. Disconnect the inlet heater hose and the outlet heater hose from the heater core.
  6. Remove the mounting nut from the heater unit. Take care not to damage or bend the fuel lines, the brake lines, and related parts.
  7. Remove the dashboard.
  8. Remove the evaporator.
  9. Remove the mounting bolts and remove the heater unit. Front heater unit honda-10-00-4128.gif

  10. Remove the self-tapping screws and the clamp.
  11. Carefully pull out the heater core so you don't bend the inlet and outlet pipes.
Front heater core honda-10-00-4129.gif

To Install:
  1. Using care, install the heater core to the heater unit and secure.
  2. Using care, install the heater unit and tighten mounting nuts and bolts to 7 ft-lb (10 Nm).
  3. Install the evaporator.
  4. Install the dashboard.
  5. Connect the inlet heater hose and the outlet heater hose to the heater core.
  6. Connect the heater valve cable to the heater valve.
  7. Refill the cooling system with engine coolant.
  8. Adjust the heater valve cable.
  9. Make sure that there is no coolant leakage.
  10. Make sure that there is no air leakage.
  11. Connect the negative battery cable.
  12. Perform the power window control unit resetting procedure.
  13. Enter the anti-theft codes for the audio and the navigation system, and then enter the audio presets.
Rear To Remove:
NOTE: The rear blower motor, the rear heater core, the blower screen, the rear blower resistor (heating/air conditioning system) and the rear power transistor (climate control system), the rear air mix control motor (climate control system) , the rear mode control motor and the rear expansion valve can be replaced without removing the rear heater-A/C unit.
  1. Remove the self-tapping screws and the clamp, and then remove the bolts and the rear evaporator lines with the rear expansion valve. If necessary, remove the rear expansion valve. Use a second wrench to hold the other fitting on the valve so the rear evaporator lines won't twist. Leave the first fitting loosely connected so you can use it to hold the valve while you loosen the second fitting.
  2. Remove the rear heater hoses.
  3. If necessary, remove the rear blower motor, the rear heater core, the blower screen, the rear blower resistor (heating/air conditioning system), the rear power transistor (climate control system), the rear air mix control motor and the rear mode control motor.
  4. Remove the self-tapping screws and the lower housing.
  5. Remove the self-tapping screws, and carefully separate the left upper housing from the right upper housing. Remove the rear heater core.
Rear evaporator assembly honda-10-00-4116.gif

To Install:
  1. Replace the rear heater core.
  2. Attach the heater hoses.
  3. Make sure no air is leaking from the left upper housing and the right upper housing fitting and from the upper housings and the lower housing fitting.
  4. Before reassembly, make sure that the rear air mix control linkage and door move smoothly without binding.
  5. Before reassembly, make sure that the rear mode control linkage and door move smoothly without binding.
  6. Reassemble the housing.
  7. After reassembly, make sure the rear air mix control motor runs smoothly.
  8. After reassembly, make sure the rear mode control motor runs smoothly.
  9. Refill the cooling system and make sure that there is no coolant leakage.
prev.gif next.gif

Oct 16, 2010 | 2005 Honda Pilot

1 Answer

The fan on my dashboard is not working. I am thinking of replacing it with a used one from a junk yard except I dont know where is located.


it's behind the glove box. here are procedures from autozone.com:

CAUTION The Supplemental Inflatable Restraint (SIR) system must be disarmed before removing the blower motor assembly. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.
  • Disconnect and isolate the negative battery cable, then wait 2 minutes before proceeding with the removal. This will effectively disable the air bag system preventing possible personal injury.
Remove the glove box from the instrument panel.


17baf45.gif


Fig. The blower motor is located behind the glovebox, behind the blower motor cover


  • Remove the A/C-heater blower motor cover.
  • Disconnect the blower motor wiring connector.
  • Remove the blower motor wiring grommet and feed the wiring through the blower motor housing.
Remove the blower motor mounting screws.


41198be.gif


Fig. Once the cover is removed, unplug the electrical connector and push it through the opening in the housing


803e435.gif

Fig. The blower motor is secured to the housing with three small screws


Allow the blower motor assembly to drop downward to clear the instrument panel and remove from vehicle.


To install:

  1. Place the blower motor assembly into position on the A/C-heater unit and tighten the mounting screws.
  2. Route the blower motor wiring through the blower motor housing and seat the wiring grommet in the hole of the blower motor housing.
  3. Reconnect the blower motor electrical connector.
  4. Install the A/C-heater blower motor cover.
  5. Install the glove box into the instrument panel.
  6. Reconnect the negative battery cable. Check blower motor operation.

Oct 15, 2010 | 2003 Dodge Caravan

1 Answer

How to replace a heater fan motor, is it changeable from the engine compartment?


No, but it isn't too hard to get to under dash. I will paste instructions from autozone.com below. Pictures may not come thru.

CAUTION The Supplemental Inflatable Restraint (SIR) system must be disarmed before removing the blower motor assembly. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.
Front Blower Motor
See Figures 1, 2 and 3



0900c1528003c5cf.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: The blower motor is located behind the glovebox, behind the blower motor cover

  1. Disconnect and isolate the negative battery cable, then wait 2 minutes before proceeding with the removal. This will effectively disable the air bag system preventing possible personal injury.
  2. Remove the glove box from the instrument panel.
  3. Remove the A/C-heater blower motor cover.
  4. Disconnect the blower motor wiring connector.
  5. Remove the blower motor wiring grommet and feed the wiring through the blower motor housing.
  6. Remove the blower motor mounting screws.




0900c1528003c5d0.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: Once the cover is removed, unplug the electrical connector and push it through the opening in the housing



0900c1528003c5d1.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: The blower motor is secured to the housing with three small screws

  1. Allow the blower motor assembly to drop downward to clear the instrument panel and remove from vehicle.

To install:
  1. Place the blower motor assembly into position on the A/C-heater unit and tighten the mounting screws.
  2. Route the blower motor wiring through the blower motor housing and seat the wiring grommet in the hole of the blower motor housing.
  3. Reconnect the blower motor electrical connector.
  4. Install the A/C-heater blower motor cover.
  5. Install the glove box into the instrument panel.
  6. Reconnect the negative battery cable. Check blower motor operation.

Sep 15, 2010 | 1999 Chrysler Town & Country

1 Answer

Where is the blower motor resistor in a 2001 dodge caravan se. I do not see it behind the glove box. I do see soemthing similar under the hood on the passenger side aginst the firewall but it is not...


Caravan, Grand Voyager, Town and Country, Voyager, 2000-2004
Blower Motor - Removal & Installation
  1. Disconnect and isolate the negative battery cable, then wait 2 minutes before proceeding with the removal. This will effectively disable the air bag system preventing possible personal injury.
  2. Remove the glove box from the instrument panel.

    a1b7373.jpg
    Fig. The blower motor is located behind the glovebox, behind the blower motor cover
  3. Remove the A/C-heater blower motor cover.
  4. Disconnect the blower motor wiring connector.
  5. Remove the blower motor wiring grommet and feed the wiring through the blower motor housing.
  6. Remove the blower motor mounting screws.

    bdc6158.jpg
    Fig. Once the cover is removed, unplug the electrical connector and push it through the opening in the housing

    063bc30.jpg

    Fig. The blower motor is secured to the housing with three small screws
  7. Allow the blower motor assembly to drop downward to clear the instrument panel and remove from vehicle.
To install:
  1. Place the blower motor assembly into position on the A/C-heater unit and tighten the mounting screws.
  2. Route the blower motor wiring through the blower motor housing and seat the wiring grommet in the hole of the blower motor housing.
  3. Reconnect the blower motor electrical connector.
  4. Install the A/C-heater blower motor cover.
  5. Install the glove box into the instrument panel.
  6. Reconnect the negative battery cable. Check blower motor operation.


Auxiliary Heater and Air Conditioner
Blower Motor - Removal & Installation
  1. Disconnect and isolate the negative battery cable.
  2. Remove the right quarter trim panel as follows:
    1. Remove first rear seat. Remove the second rear seat, if equipped.
    2. Remove the sliding door sill plate.
    3. Remove the quarter trim bolster.
    4. Remove the upper C-pillar trim and D-pillar trim panel.
    5. Remove the first and second rear seat belt anchors.
    6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
    7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
    8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.

      1dc958e.jpg
      Fig. Removing the trim panel to access the rear blower motor
    9. Disconnect the wiring harness connector from the accessory power outlet, if equipped.
    10. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.
    11. Pull first rear seat belt through the access hole.
    12. Remove the quarter trim panel from the vehicle.
  3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  4. Twist the blower motor out of scroll housing.
  5. Disconnect the blower motor wiring connector.
  6. Remove the blower motor from vehicle.

    1e2cfdc.jpg
    Fig. The rear blower motor is held in place by four screws
To install:
  1. Install the blower motor unit into the vehicle.
  2. Reconnect the blower motor wiring connector.
  3. Secure the blower motor into scroll housing.
  4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  5. Install the right quarter trim panel as follows:
    1. Install the quarter trim panel in position in the vehicle.
    2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
    3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
    4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
    5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
    6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
    7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
    8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
    9. Install the D-pillar trim panel and upper C-pillar trim.
    10. Install the quarter trim bolster.
    11. Install the sliding door sill plate.
    12. Install the second rear seat, if equipped, and install the first rear seat.
  6. Reconnect the negative battery cable. Check blower motor operation.

Hope helps (remember rated this).

Jul 11, 2010 | 2001 Dodge Grand Caravan

1 Answer

How do you change a heater blower moter in a 1998 Dodge grand caravan


Removal & Installation


afab437.gif

The blower motor is located behind the glovebox, behind the blower motor cover

  1. Disconnect and isolate the negative battery cable, then wait 2 minutes before proceeding with the removal. This will effectively disable the air bag system preventing possible personal injury.
  2. Remove the glove box from the instrument panel.
  3. Remove the A/C-heater blower motor cover.
  4. Disconnect the blower motor wiring connector.
  5. Remove the blower motor wiring grommet and feed the wiring through the blower motor housing.
  6. Remove the blower motor mounting screws.

b4976b0.gif
Once the cover is removed, unplug the electrical connector and push it through the opening in the housing


31d76b2.gif
The blower motor is secured to the housing with three small screws

  1. Allow the blower motor assembly to drop downward to clear the instrument panel and remove from vehicle.
To install:
  1. Place the blower motor assembly into position on the A/C-heater unit and tighten the mounting screws.
  2. Route the blower motor wiring through the blower motor housing and seat the wiring grommet in the hole of the blower motor housing.
  3. Reconnect the blower motor electrical connector.
  4. Install the A/C-heater blower motor cover.
  5. Install the glove box into the instrument panel.
  6. Reconnect the negative battery cable. Check blower motor operation.

May 24, 2010 | 1998 Dodge Caravan

1 Answer

How to remove a heater blower motor on a 2004 Dodge Caravan.


Please don"t forget to rate:

Removal & Installation
CAUTION The Supplemental Inflatable Restraint (SIR) system must be disarmed before removing the blower motor assembly. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.


  1. Disconnect and isolate the negative battery cable, then wait 2 minutes before proceeding with the removal. This will effectively disable the air bag system preventing possible personal injury.
  2. Remove the glove box from the instrument panel.
a58c6c0.gif
The blower motor is located behind the glovebox, behind the blower motor cover

  1. Remove the A/C-heater blower motor cover.
  2. Disconnect the blower motor wiring connector.
  3. Remove the blower motor wiring grommet and feed the wiring through the blower motor housing.
  4. Remove the blower motor mounting screws.
99bec31.gif
Once the cover is removed, unplug the electrical connector and push it through the opening in the housing

20bb980.gif
The blower motor is secured to the housing with three small screws

  1. Allow the blower motor assembly to drop downward to clear the instrument panel and remove from vehicle.
To install:
  1. Place the blower motor assembly into position on the A/C-heater unit and tighten the mounting screws.
  2. Route the blower motor wiring through the blower motor housing and seat the wiring grommet in the hole of the blower motor housing.
  3. Reconnect the blower motor electrical connector.
  4. Install the A/C-heater blower motor cover.
  5. Install the glove box into the instrument panel.
  6. Reconnect the negative battery cable. Check blower motor operation.

Jan 04, 2010 | 2004 Chrysler Voyager

1 Answer

Replace heater blower motor 96 neon


With Air Conditioning
  1. Disconnect the negative battery cable.
  2. Remove the right side scuff plate.
  3. Pull back the carpet from the passenger's side floor.
WARNING Be careful not to cut into the blower motor wiring!

  1. Use a suitable utility knife to cut the wheel housing silencer in line with the blower motor wiring.
  2. Detach the blower motor electrical connector.
  3. For right-hand drive vehicles, remove the motor cover.
  4. Unfasten the three blower motor retaining screws, then lower the blower motor assembly from the unit housing.

3efc4db.gif
The blower motor assembly is located under the passenger's side dash panel


c91626e.gif
Blower motor mounting and location of the retaining screws and wiring-vehicles with A/C

To install:
  1. Raise the blower motor into position in the unit housing and secure with the three retaining screws.
  2. If removed, install the motor cover.
  3. Attach the blower motor electrical connector.
  4. Use tape to secure the silencer into position.
  5. Reposition the passenger's side floor carpeting.
  6. Install the right side scuff plate.
  7. Connect the negative battery cable.

Oct 25, 2009 | Chrysler Neon Cars & Trucks

2 Answers

How do you replace the blower motor on 92 accord wagon - where is it located?


Disconnect the negative battery cable (if you have an anti-theft radio, make sure you have the code).
The blower unit is located in the dash, behind the glove box.
Remove the glove box and the glove box frame(damping screws on the sides and two screws underneath).
If the car isn’t equipped with air conditioning, remove the heater duct between the heater core and the blower assembly housings. Then remove the three blower housing retaining nuts, pull the blower housing out far enough to unplug the electrical connectors (at the lower right edge, right above the kick panel) and remove the blower assembly housing.
If the car has air conditioning, remove the strap bolt, the blower under cover and the three blower housing retaining nuts, then remove the blower assembly as previously described.
If you are replacing the blower motor itself, or either of the blower fan wheels, remove the motor, remove the retaining clip(s) and remove the fan wheel(s).
Reverse procedure to install.
Hope this helps you.

Oct 19, 2009 | 1992 Honda Accord

2 Answers

Kia Sportage heater core removal and replacement


Hi there,

Here are the steps to remove heater core

1. Chock wheels. 2. Drain the engine coolant. Refer to Engine Cooling System. 3. Discharge and recover the refrigerant from the A/C system. Refer to Recovery/Evacuating/Charging in this section. 4. Remove the dash panel. Refer to Body. 5. Remove the Blower/Evaporator unit. Refer to Blower/Evaporator Unit in this section. 6. Disconnect the low pressure line from the evaporator outlet on the bulkhead. 7. Disconnect the high pressure line from the evaporator inlet on the bulkhead. 8. Disconnect the heater return hose from the heater core outlet tube connection. 9. Disconnect the heater inlet hose from the heater core inlet tube connection. 10. Disconnect the fresh air/recirculation control cable from the blower housing unit inlet duct. 11. Disconnect five connectors at the bottom of the blower housing unit. 12. Pull carpeting away from bulkhead to gain access to the hole cover plate. 13. Remove the four nuts retaining the hole cover plate. 14. Remove the hole cover plate. 15. Remove two mounting bolts at the top of the blower housing unit. d40e96a.jpg 16. Remove two nuts attaching the bottom of the blower housing unit to the bulkhead mounting studs. 17. Remove the blower unit from the vehicle. 18. Remove the temperature control cable from the heater unit servo. 19. Remove the two nuts from the mounting studs at the bottom of the heater unit. 20. Remove the top nut holding the heater unit to the bulkhead to the bulkhead mounting stud. 21. Remove the heater unit. Regards, Jeep Brainy

Apr 15, 2009 | 1997 Kia Sportage

1 Answer

How to repair a 1996 kia sportage heating core


Hi there,

I hope below steps can help ...


1. Drain the engine coolant. Refer to Engine Cooling System. 2. Discharge and recover the refrigerant from the A/C system. Refer to “Recovery/Evacuating/Charging” in this section. 3. Remove the dash panel. Refer Body. 4. Remove the blower/ evaporator unit. Refer to “Blower/Evaporator unit” in this section. 5. Disconnect the low pressure line from the evaporator outlet on the bulkhead. 6. Disconnect the high pressure line from the evaporator inlet on the bulkhead. 7. Disconnect the heater return hose from the heater core outlet tube connection. 8. Disconnect the heater inlet hose from the heater core inlet tube connection.




d1a8fa0.jpg





9. Disconnect the fresh air/recirculation control cable from the blower housing unit inlet duct. 10. Disconnect five connectors at the bottom of the blower housing unit. 11. Pull carpeting away from bulkhead to gain access to the hole cover plate. 12. Remove the four nuts retaining the hole cover plate. 13. Remove the hole cover plate. 14. Remove two mounting bolts at the top of the blower housing unit. 15. Remove two nuts attaching the bottom of the blower housing unit to the bulkhead mounting studs. 16. Remove the blower unit from the vehicle. 17. Remove the temperature control cable from the heater unit servo. 18. Remove the two nuts from the mounting studs at the bottom of the heater unit. 19. Remove the top nut holding the heater unit to the bulkhead to the bulkhead mounting studs.
20. Remove the heater unit.




Regards,
Jeep Brainy

Oct 25, 2008 | 1996 Kia Sportage

Not finding what you are looking for?
1994 Chevrolet C1500 Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...