Question about Hyundai Elantra

1 Answer

Power sterring control valve leak

I have a 1979 corvette the power sterring control valve has a minior leak at the adjustment nut will Lucas power sterring stop leak work on that application?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 5,158 Answers

The principle of that stop leak is that it swells up the rubber on seals.... once the seals wear again it won't work as well... but if there is a seal on that adjustment nut it will work....

Robert

Posted on Dec 17, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I balance or adjust the power steering control valve on a 1975 Corvette?


If your steering is operating normal and you replaced the valve, a front end aling will staighten your wheels and center your steering wheel

Dec 02, 2014 | Chevrolet Corvette Cars & Trucks

1 Answer

93 toyota camry. 4 cylinder. need to know how to change power sterring belt.


RAISE AND SUPPORT THE VECHICLE SAFELY, REMOVE THE FAN SHROUD.REMOVE THE RIGHT FRONT WHEEL AND THE ENGINE UNDER COVER, REMOVE THE LOWER SUSPENSION CROSSMEMBER IF NECESSARY,LOOSEN THE ADJUSTING NUT FROM BEHIND THE PUMP PULLEY AND LOOSEN THE PIVOT BOLT. DISCONNECT THE VACUUM HOSES FROM THE AIR CONTROL VALVE, IF EQUIPPED, WITH DRAW THE BELT. ON SOME VECHICLES IT MAY BE NECESSARY TO REMOVE THE PULLEY IN ORDER TO REMOVE THE DRIVE BELT.

Apr 07, 2011 | 1993 Toyota Camry V6

1 Answer

Noisey engine when hot, sounds like lifters?? only has 52000 miles\r\n 1992 corvette lt1


Try using the additive called lucas oil treatment,with your oil change,wear can cause this,and the lucas will lube better,and cause the lifters to fill up easy.

Jun 13, 2010 | 1992 Chevrolet Corvette

1 Answer

Frank,on a mb 1979 300d the engine runs but nun of


Check the center lower pulley harmanic balancer if center of pulley spinning, could be broken and just spinning on outer pulley hub.Hope this was very helpful Good luck

Dec 24, 2009 | 1983 Mercedes-Benz 300-Class

1 Answer

Free wiring down load for 1979 corvette


1979 Corvette turn signal....lever falls off...how do i get the other part of turn signal lever off or out???

Oct 12, 2009 | Chevrolet Corvette Cars & Trucks

1 Answer

Idle is too high ,have replaced the idle control motor and correcly set the T P S.


when you put new idle speed control in you have to adjust it to make it work.if all is good. your throttle valve sticking open.due to gum and carbon build up around valve.or your throttle cable need adjusting.could be out of adjustment..

Jul 13, 2009 | 1987 Chevrolet Corvette

1 Answer

While running engine runs hard. Also tapping or ticking sounds after installed new oil pump ,pan and gasket. I've been told is the lifters. So Ive tried lucas oil stablaizer, Mystery oil and CD2 still...


If you have an adjustable valve train you may need to adjust the rocker arms. Remove the valve covers and look to see if there are adjusting nuts on top of them. If so, get a shop manual and a feeler gague and a couple of wrenches and screwdriver and follow instructions in manual carefully.

May 20, 2009 | 1986 Mercedes-Benz 300

2 Answers

Need wiring diagram for 1979 corvette


Tried to reach you twice...I have the entire car diagram just need to know how/where to send!!!

May 12, 2009 | 1972 Chevrolet Corvette

1 Answer

Need valve adjustment specs for 1979 ford f-250 6 cyl


did u soak the lifters in oil 1st before installing them? if they are pumped up u bring that cylinder u are adjusting up on compression stroke, then adjust rocker to zero lash and then 1/2 more turn of the adjusting nut.

Mar 22, 2009 | Ford F-250 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

61292 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...