Question about 2004 GMC Envoy

1 Answer

2004 xl envoy ip lights comin on all 4 small guauges are non operational 2 large works this morning key remote wouldnt unlock doors open one door with key no other doors would unlock and the car will not start but the head light and ip light come on with interior light

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Your batter is slowly dying! replace it before its too late. i had the same problem and i kept boosting it and using a trickle charger...just change it to a good battery

Posted on Dec 21, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2003 GMC Envoy with 79k miles. I have


sounds like 1 of 2 problems. without the vehicle it is hard to say but first I would check the ignition switch and then look at the body control module. hope this helps,
The body control module controls keyless entry and most body functions including dash board operations.

Jul 22, 2010 | 2003 GMC Envoy

3 Answers

TDS 3-button keyless remote operating instructions please


RED opens the drivers door, BLACK opens all the doors, and GREEN turns on the head lights

Apr 30, 2010 | 1998 Toyota Camry

1 Answer

Keyless entry not working


Programming
When
Remote control added or replaced. System malfunction.
How
Obtain all remote controls. Remove key from ignition switch. Close all doors. Open driver's door. Carry out the following within 24 seconds: Turn ignition switch ON and back to LOCK position 3 times. Remove key. Press and release driver's door courtesy light switch 3 times. Ensure doors lock and unlock. If not, wait 40 seconds and repeat procedure starting with driver's door already open. Press each remote control lock or unlock button twice. Ensure doors lock and unlock after each remote control operation. If not, proceed as follows: Press and release driver's door courtesy light switch once. Ensure doors lock and unlock twice. Repeat procedure starting with driver's door already open.
NOTE: A maximum of 3 remote controls can be programmed.

Mar 29, 2010 | 2004 Mazda 6

1 Answer

2004 Envoy Xuv tailgate does not open.


pull the plastic off of the tailgate and make sure the small wire looking controls are still hooked up. sometimes they will pop out after alot of use. other thing is make sure the rear actuator is actually working (it could be bad)

Jun 20, 2009 | 2004 GMC Envoy

3 Answers

Central Locking not working


Hi Craig,
I'm running a E34 Tds Touring with a similar problem, my rear doors and tailgate have dropped of the central locking circuit.
I have been told it is the Central locking Module a large black box under the dash that is faulty, apparently a common problem.
Hope this points you in the right direction,
Please remember to rate my effort!
Paul 'W'
Onyer~EDson(:0) {#><U.K.

Jan 19, 2009 | 1999 BMW 318 ti

1 Answer

Remote key fob will not work-battery replaced


VW/AUDI/SEAT/SKODA



Remote Control Programming (1997 ON)

Procedure
1. Switch Ignition ON and leave the key in the ignition.

2. Mechanically lock the vehicle using the Drivers door using a second
key.

3. Using the remote control press the Unlock button once, and the horn
will sound once.

4. Wait 6 seconds and press the unlock button once to activate the coding
procedure. The remote control will now be programmed.

NOTE : When performing programming on additional remotes the procedure
is the same, except you press the unlock button 2, 3 or 4 times for the
different remote.

For example : If programming 2 remotes press the unlock button twice with
a 1 second interval between each press, repeat for 3 and 4 remotes.

5. Switch Ignition OFF.

6. Remove key from ignition and check for operation.

7. The coding procedure can be repeated up to 4 times for additional remotes.

8. The ignition must be switched OFF between programming each remote
control.

Remote Control Erasing (1997 ON)

Procedure
1. Switch Ignition ON and leave the key in the ignition.

2. Mechanically lock the vehicle using the Drivers door using a second
key.

3. Press the remote control unlock button 5 times in 1 second intervals.
A short horn will sound.

4. Wait 6 seconds and press the unlock button once to activate memory
erase.

5. Switch ignition OFF, all remotes are now erased.

Dec 24, 2008 | 2004 Volkswagen New Beetle Convertible

2 Answers

Central locking not working on key.


Before you spend bigger amount, check the battery in the key. Usually a CR2032 battery can be find there. (Open the Keyfob by inserting an object into the key ring holder and pulling the top and bottom apart, Seperate the two halfs, Open the top half to expose the battery... )

Nov 28, 2008 | 1998 Audi A6

1 Answer

Key will not unlock door


the lock on the driver side could be damaged or some on might have used a jimmy to open that door before how evr you have to open the pannel and remove the lock cylinder part and make sure that the key is working or yo must change the tumbler s in the lock to fit your key (lock smith)

Nov 19, 2008 | 2002 GMC Envoy

3 Answers

Door lock 2004 jetta wagen


If remote locks and unlocks driver door but does not unlock passenger doors,then follow the advice above:
Get in the car using the key to unlock the doors. From the passenger side lock and unlock your doors using the button on the passenger door. Get out and the remote should now unlock all the doors with 2 presses.
Worked perfectly for me after several other suggestions (and dealer) failed.

Nov 07, 2008 | 2004 Volkswagen Jetta

1 Answer

Remote entry key.


You may have lost programming in the remote.
Here are the instruction to program it

1. Confirm that all doors are closed and the ignition key is NOT in the ignition cylinder.
2. Open the driver's door and within 10 seconds insert the key in the ignition.
3. Now, within 10 seconds remove the key from the ignition.
4. Within the next 20 seconds, push and release the driver's door switch 3 times. This is the switch near the door strike plate which turns on the inside light and indicates that the door is open.
5. Within 10 seconds, insert the key in the ignition.
6. Now, within 10 seconds remove the key from the ignition.
7. Within the next 20 seconds, press and hold both the LOCK and UNLOCK buttons on the transmitter. Hold both for at least 5 seconds. All the doors will lock or unlock to confirm that procedure was done properly.
8. Within the next 5 seconds after step 7 was complete, press either the LOCK or UNLOCK button to confirm that this process has been properly done. Now, the transmitter has been programmed.
9. Repeat steps 1 to 8 for additional transmitters.
10. Operate each transmitter to verify the programming.

Sep 04, 2008 | 2004 Suzuki Verona

Not finding what you are looking for?
2004 GMC Envoy Logo

Related Topics:

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...