Question about 2002 Ford E350

1 Answer

96 ford e350, brake pedal goes to the floor when running

Replaced master, booster, front calipers

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 57 Answers

Check for fluid leaks, possibly rear brake cylinders. has anything else been replaced prior to this concern?

Posted on Dec 17, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have replaced 3 disc brake calipers on my 2001 pt cruiser. after bleeding all 4 brakes 3 times, I started the car and brake pedal goes to floor. is my brake booster shot?


Michael:

You must start bleeding the brakes at the wheel farthest from the master cylinder (usually the right rear), then the next farthest from the master cylinder, then the next, then the closest. If your master cylinder is at the left front of the car, start with the right rear, then the left rear, then the right front, then the left front. If you don't bleed the brakes in the correct order, you are just shifting the air in the lines from one line to another. Make sure that you close the bleeder before letting the brake pedal up, and the engine should not be running when you bleed the brakes... Make sure that the emergency brake is off. Make sure that the master cylinder does not run out of brake fluid at any time that you are bleeding the brakes.

Jan 24, 2016 | 2001 Chrysler PT Cruiser

1 Answer

I Got a 2000 ford expedition i replace front brake pads, calipers brake pedal goes all the way to the floor I replace the booster and master cylinder and the problem don't go away


I would start by bleeding the air out of the brake system starting at the longest line first. Check for fluid in the master cylinder . IF you have problems bleeding then undo the lines at the master cylinder and using your fingers a valves bleed the air out and prime the master cylinder first then bleed the system

Feb 24, 2014 | Ford Expedition Cars & Trucks

1 Answer

Ford e350 no brakes!!


Need purge the system for air inside!!!!

Mar 18, 2010 | 2002 Ford E350

3 Answers

Just replaced master cylinder on 1990 aerostar and bled the brakes, still the pedal goes to floor and i have no brakes


Did you bench bleed the master cyl. before installing it? then when you installed the new master, did you bleed all 4 points? If yes, then check all for points for leaking caliper/s and leaking wheel cylinder/s. If the van has ABS, check the valve body for a bleeder screw and see if air bleeds out of it. If you've checked everything twice and did everything right then your new master cyl. may be defective.

Apr 29, 2009 | 1986 Ford F 250

2 Answers

Bleeding brakes


always bleed front driver side first, front right,left back
right back.
make sure you always have oil in the master

Apr 08, 2009 | 1993 Dodge Dakota

3 Answers

1994 ford explorer will not stop, I have replaced the brake pads,


My vote would be the Master Cylinder.
I had a truck sit for 4 years. After getting running again, it did the same thing you're describing. No brakes. I ended up replacing the Master Cylinder to fix the problem. Just make sure you bleed the system real good.

Mar 25, 2009 | 1994 Ford Explorer Limited

2 Answers

97 ford e350 brake pedal goes to the floor...


are your rear drums set up? why did you bleed the brakes. when only when you installed new pads?

Sep 11, 2008 | 2002 Ford E350

Not finding what you are looking for?
2002 Ford E350 Logo

406 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

82322 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

gerry bissi

Level 3 Expert

4382 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...