Question about 1998 Ford Escort

1 Answer

Cylinder head ford zetec escort p reg

I need torque settings and cam setting can you help

Posted by on

  • Anonymous Mar 28, 2014

    need to torque cylinder head

  • Anonymous Mar 28, 2014

    cam sprockets ,jackshaft, crankshaft torque settings

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 58 Answers

Stage 1 = 15Nm
Stage 2 = 40Nm
Stage 3 = Plus 90 degrees or quarter of a turn. Good tip is to mark all the bolts after initial torque setting with tip-ex , i.e. all to the front of the car. When you finish they should all point towards the timing belt.
This is also a good way to make sure you don't miss one or tighten one twice if you are distracted since it is not a torque setting. New bolts should be used by the way as they are stretch bolts. Timing of cams - remove cam cover and you will see a slot on the end of the cams. Opposite end from belt. You need to slip a piece of 5mm flat bar or a long 5mm allen key into then so that the bar rests on the face of the head. Engine should be a tdc.
cheers John

Posted on Dec 17, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the cylinder head bolts torque setting for a ford fiesta 1999 1.25?


Hello friend,
Copied from here
http://www.fordownersclub.com/forums/topic/6527-fiesta-zetec-125-tourqe-settings-help/

You will have to use an online converter from Ft/lbs to Nm if you want Imperial.

'the sequence is as follows...

8 - 6 - 1 - 3 - 9
10-4 - 2 - 5 - 7

STAGE 1: tighten to 15Nm
STAGE 2: tighten to 30Nm
STAGE 3: tighten 90 degrees

the camshaft carrier/capa are tightened to 15Nm.'

Sep 11, 2014 | Cars & Trucks

1 Answer

Cylinder head tightening sequence for ford mondeo 1.8i zetec petrol


Go to this LINK for the info in pdf format, the sequence is on page 16 of the pdf file.

Feb 15, 2012 | 1999 Ford Mondeo

1 Answer

2000 ford escort zx2 engine number 0g-774-aa. Is this a Zetec engine?


if it is a 2000 escort 2-door zx2 then yes it has a zetec engine
dual over head cam 2.0

Aug 08, 2010 | 2000 Ford Escort

1 Answer

Set timing marks for escort zetec 16 v


valve timing marks on back of cams ,a slot on back of cam has to level with the head ,crank timing on the flywheel ,hole in bellhousing

Jun 10, 2010 | 1996 Ford Escort 4 Door

1 Answer

Hi iv got an escort 1.8 16v zeetec its r reg and iv had the head re conditioned i need 2 put the head bck on but i need to no the torqe setting can u help me thankyou.


hi yes here are the torque settings

stage 1 is 25nm
stage 2 is 45nm
stage 3 is turn 105 degrees

try leaving about 10 mins between each torque so it can settle also you have to tighten them in sequence and make sure you use new head bolts as these are the stretch type and if you are using the old ones there could be a chance of one snapping, just a little advice..hope this helped

Feb 15, 2010 | 1998 Ford Escort

1 Answer

Could you help me with the ford escort 1600 zetec (1995) twin cam cylinder head torque settings please regards tom


Tightening sequence is (imagining the bolts looking down from the front of the car, top left to right being bolts 1,2,3,4,5 and bottom left to right being bolt 6,7,8,9,10 the tightening order is 8,3,9,2,7,4,6,5,10,1 Draw it out on paper to make it become clear. (it will I promise)
The tightening is done in stages, Stage one being to screw all the bolts in finger tight. Stage two is tightening the bolts in sequence to 20-30nm Stage three is tightening the bolts in sequence up to 40-50nm Stage four is tightening the bolts in sequence by 90-120 degrees. ---- Data checked and double checked, thats the official way to do it.


Jan 23, 2010 | 1995 Ford Escort

1 Answer

Require ford escort rs 2000 1976 torque settings head bolts


2lt overhead cam with them horrible tappet adjusters,cast iron head but valves dont hit the head if the timing belt breaks ,but it does on the 1600 .called a pinto in america .Remember the assembly line well ,have many a fond memory of working on it and the staff canteen on night shift ,what lovely grub we got.Head bolt torque is about 80lbs because i used to pull them down to check them after the machine had tightened them up

Apr 24, 2009 | 1997 Ford Escort

1 Answer

2000 W reg ford escort wheel nut torque settings


2.0L DOHC Engine 85-105 Ft Lbs EX 2.0L DOHC Engine 65-87 Ft Lbs

Please let me know if this information is helpful. Positive feedback is appreciated. Thank You!

Mar 28, 2009 | 1989 Ford Escort

1 Answer

Hi i need the torque setting for ford escort p reg cylinder head and cam bearing can you help


hi the cylinderhead torque settings are
STAGE 1, 30Nm (22l bf ft)
STAGE 2, 50Nm ( 337 lb ft ),
STAGE 3, angle tighten another 90 degrees,
STAGE 4 angle tighten another 90 degrees

Cant help you with the cam bearing though sorry

Dec 17, 2008 | 1998 Ford Escort

Not finding what you are looking for?
1998 Ford Escort Logo

333 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63990 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...