Question about 1999 Daewoo Lanos

1 Answer

A SOCKET FELL INTO THE TIMING BELT HOUSING AND CHEWED UP THE GEARS WHAT PARTS DO I NEED

Posted by on

  • yadayada
    yadayada May 11, 2010

    everything that is damaged, why what did u think??

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 99 Answers

As long as the housing is ok covering the belt, you will more than likely need tensioner, complete timing kit (belt, crank sprocket and cam sprocket) and any guides or rollers the belt may ride on. Also make sure it didn't bend the cam, if it got roled up in the belt it could have bent the cam or done other damage.
Good luck!

Posted on Dec 17, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

The timing belt tensioner failed on my 2000 saturn Ls2 now the timing is off how do i get it back 2 tdc i got new belt n all pulleys but dont want 2 take belt off b4 i know how 2 get the timing back t


Remove Belt.Turn crankshaft pulley mark to line up with mark on housing TDC. Turn camshaft gear mark to line up with mark on head or block housing. More than one mark on cam gear ? If so turn camshaft till number four cylinder inlet and exhaust valves are just rocking this is the mark to use. ( same can be used on a six cylinder engine rocking number six valves ) fit new parts, tension belt, (TIP) now turn engine twice by hand , recheck that timing marks line up . saves a lot of time if you find they don't later.

Sep 16, 2014 | Cars & Trucks

1 Answer

How to install timing belt on 1996 dodge grand caravan


The timing belt is inside the housing (plastic) and if it was off then the engine would not have been running. The belt you saw is the serpentine belt and drives the accessories such as alternator --fan---power steering---water pump---ac compressor. With it missing the engine would have no water pump or fan and would have been getting quite hot. Get a new belt and if you have a owners hand book the lay out will be in a diagram.

Jan 08, 2014 | 1996 Dodge Grand Caravan

1 Answer

Need timing marks on a 2002 deawoo nubira


Required tools:

13mm open end wrench 10mm shallow and deep socket 8mm socket long flathead screwdriver 17mm deep socket T50 torx socket 1/4", 3/8ths and 1/2" ratchets and extensions E10 inverted torx sockets 6mm Allen wrench 15mm open end wrench 7mm socket 12mm open end wrench 14mm socket 12mm socket 8mm, 9mm and 10mm Allen head sockets 19mm socket pry bar needle nose pliers

If you are doing this because your timing belt broke you will also need to buy a complete cylinder head, head gasket set, and both idler pulleys. ALL DAEWOO MODELS WILL BREAK THE INTAKE AND EXHAUST VALVES WHEN THE TIMING BELT BREAKS.

Start by removing the air cleaner assembly from the throttle body, remove the air filter and housing jack up the vehicle and remove the wheel, remove the plastic shielding in front of the accessory drive belt assembly, remove the accessory drive belt, place a jack with a block of wood on top underneath the engine oil pan remove the front engine mount, remove the crank shaft pulley ( the 4 Allen head bolts only not the 17mm bolt in the center.) remove the metal plate behind the engine mount bracket on the engine, remove the plastic timing belt cover 3 clips on top 2 10mm bolts on bottom. Rotate the engine until the #1 cyl. is at Top Dead Center on the compression stroke or line up the crankshaft timing mark with the mark on the inner timing belt cover ( notch in cover with notch in pulley) on the camshaft pulleys -- ( intake cam line up the line on the pulley with the line on the inner cover)( exhaust cam line up the arrow on the pulley with the arrow on the inner cover) loosen the 13mm bolt in the belt tensioner and using the Allen wrench rotate the tab until there is slack in the belt. Remove the belt. At this time I would recommend you replace the water pump, both plastic idler pulleys as they tend to overheat and lockup, and the belt tensioner. Make sure all your marks are lined up, you may need a helper to hold the Exhaust Cam in place as it tends to move during belt installation. Put the timing belt underneath the crankshaft pulley, install the belt leaving the intake cam for last and NO BELT SLACK on the right side between the crank and the exhaust cam. Once the belt is installed rotate the crankshaft over 2 revolutions and make sure is rotates freely, and your timing marks are aligned perfectly if not the engine will not run properly, tension the belt as needed. Installation is the same as removal.



To clarify, on the DOHC engine, the intake cam gear has a line on it, and the exhaust cam gear has an arrow on it. These should be lined up with the corresponding line and arrow on the VALVE COVER, pointing straight up. I just went through this process over the weekend, and spent quite a bit of time looking for these marking as I had removed the valve cover. Once I found them, it was plain and simple.

In addition, be sure to not over tighten the belt when reinstalling. The tensioner has markings on it for "old" and "new". DO NOT adjust past "new", as the car will sound like a jet engine, and the belt will not last for very long.

One more item that you may as well replace while you are in there is the cam position sensor if you have not already, as there have been issues with them, and the timing housing has to be opened to get to it

Oct 17, 2012 | Cars & Trucks

1 Answer

I would like a diagram of the 2004 Suzuki forenza timing marks and how to get the belt aroujd the crankshaft is there a way you can give me that information?


from autozone.com


Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Disconnect the Manifold Air Temperature (MAT) sensor connector.
  4. Disconnect the air cleaner outlet hose from the throttle body.
  5. Disconnect the breather tube from the camshaft cover.
  6. Remove the air cleaner housing bolts.
  7. Remove the air cleaner housing.
  8. Remove the right front wheel.
  9. Remove the right front wheel well splash shield.
  10. Remove the serpentine drive belt.
  11. Remove the crankshaft pulley bolts and the crankshaft pulley.
  12. Remove the right engine mount bracket.
  13. Remove the front timing belt cover bolts.
  14. Remove the front timing belt cover.
  15. Using the crankshaft gear bolt, rotate the crankshaft clockwise until the timing mark on the crankshaft gear is aligned with the notch at the bottom of the rear timing belt cover.

56340db.gif

Fig. Aligning the timing mark on the crankshaft gear with the notch at the bottom of the rear timing belt cover.


7c6bcda.gif

  1. Fig. Aligning the camshaft gears with the notches on the camshaft cover.
  2. Align the camshaft gears with the notch on the camshaft cover.
  3. Remove the timing belt.
  4. Loosen the automatic tensioner bolt. Turn the hex-key tab to relieve belt tension.

To install:
  1. Align the timing mark on the crankshaft gear with the notch on the bottom of the rear timing belt cover.
  2. Align the timing marks on the camshaft gears, using the intake gear mark for the intake gear and the exhaust gear mark for the exhaust gear.
  3. Install the timing belt.
  4. Turn the hex-key tab in a clockwise direction to tension the belt. Turn until the pointer aligns with the notch.
  5. Install the automatic tensioner bolt and tighten to 18 ft. lbs. (25 Nm).
  6. Rotate the crankshaft two full turns clockwise using the crankshaft pulley bolt.
  7. Recheck the automatic tensioner pointer.
  8. Install the front timing belt cover.
  9. Install the front timing belt cover bolts and tighten to 53 inch lbs. (6 Nm).
  10. Install the right engine mount bracket.
  11. Install the crankshaft pulley and tighten the crankshaft pulley bolts to 15 ft. lbs. (20 Nm).
  12. Install the serpentine drive belt.
  13. Install the right front wheel well splash shield.
  14. Install the right front wheel.
  15. Install the air cleaner housing.
  16. Install the air cleaner housing bolts and tighten to 89 inch lbs. (10 Nm).
  17. Connect the air cleaner outlet hose to the throttle body.
  18. Connect the breather tube to the camshaft cover.
  19. Connect the MAT sensor connector.
  20. Connect the negative battery cable.

Sep 25, 2010 | Suzuki Forenza Cars & Trucks

1 Answer

How do you remove the timing belt cover on a 1995 VW Golf.


What is needed Tools: 6mm and 8mm allen wrench socket, 5mm allen wrench. 8mm, 13mm, 19mm socket and ratchet. 10mm combination wrench. Long ratchet extensions (at least one 6in, more are helpful). 5inch Wheel puller (for main shaft pulley). (Some models may need a special spanner tool to adjust the timing belt tensioner) Parts: 2 gal of anti-freeze mixed with distilled water. All three V-belts. (Alt, A/C, P/S) $32.95 New water pump top. $91.91 New gasket for WP. $9.13 New timing belt. $26.13.


Procedure:

Remove battery cable (either power (+) or ground (-)) remove alternator remove A/C remove power steering pump .Remove water pump pulleys remove main shaft pulleys remove timing belt covers remove A/C mounting hardware remove timing belt (don't turn any of the wheels its connected to) replace timing belt adjust belt tension remove water pump face put on new gasket and new part.

Leave pulleys off. replace bottom timing belt cover, replace crank shaft pulley, replace steering pump, replace A/C, put small belt on A/C (hang loose) put large belt around A/C, Main and water pump pulley. put middle size belt on Main water pump and power steering pump reattach bolts for the steering pump pulleys put alternator back on adjust all belts. connect battery

Problem areas:
Main pulley: There are 4 6mm hex head bolts. These must be removed. The main 19mm hex head can be used to turn the engine it the timing belt slips and you have to readjust the timing.

Putting on new belts: This can be a real pain if you get VW belts. The adjustments won't give enough to put the belts over the edge so the easy way is to remove the pulley on the water pump. Then its real easy.

Timing: If you turn the wheels that the timing belt goes on you will have to reset the timing. Mark the timing points with something like whiteout so its easy to see. The timing mark on the toothed gears are small dots. The timing mark for the crankshaft is a small cut on the outer pulley. When its aligned with the intermediate wheel timing mark (there is an arrow on the cover as a hint) should intersect as viewed from the right wheel well. The camshaft timing mark should line up with the top of the engine near the front.

Power steering pump: It is held on with lots of bolts. One is in a channel that is hard to see but can be found with a 6" extension. If you look at the pump you will see three bolts that go into the housing. This should give you an idea where the forth is.

May 01, 2010 | 1995 Volkswagen Golf

1 Answer

I need to replace the cam belt on Mazda Familia Z5 DOHC can you tell me how to line up the timing marks


After you remove the timing belt cover you will see the two small gear wheels on the top of the engine, there should be, just above the center bolts of the gears, a little raised bump or notch these are the TDC (top dead center) marks they should also have a corresponding mark on the engine housing that they will need to be pointed at. As well the crank wheel also has similar marks. These all need to be TDC. You will then thread the belt onto the gears, keeping it tight, from the crank, over the two cams, passed the tensioner and back to the crank. Turn the crank by hand two complete turns using a breaker bar and socket on the crank shaft bolt. Look at the marks and they all should be back at TDC, if not repeat the process until they are. If they are try starting the engine. A timing gun may be needed to fine tune it but it should be close enough to run. Good luck

Oct 15, 2009 | 1994 Mazda 323

1 Answer

My aveo 04 manual wont start gets a spark ,fuel and replaced timming belt it was chewd up after car stalled on me in the high way but still wont start. gears also shift into place whats wrong?


If the timing belt became chewed up it would seem the belt/timing has slipped (do not try starting it like this bad things could happen) You'll need to replace the timing belt, tensioner and insure the proper mechanical timing is done for it to run properly if at all. If the belt failed at highway speed and it has a interference fit engine this would mean a valve or two may be bent too. I'd check the timing and once this is corrected I'd checking cylinder compression.
I hope this may have helped,
Tom

Sep 07, 2009 | 2004 Chevrolet Aveo

2 Answers

TIMING BELT WON'T STAY CENTERED ON CAMSHAFT SPROCKETS


You don't mention replacing any tensioner bearing which if worn could be causing the belt to drift.
I would probably remove any covers and physically watch the belt to try to determine which of the surfaces on which the belt runs is at fault. I think the belt is probably not that cheap so I hope you cure this soon.   

Mar 28, 2009 | 1999 Mercury Cougar

2 Answers

Lincoln distributor


Make sure the tensioner is tight to the specifications and in propper place.
See
CHECKING YOUR TIMING BELT and TENSION.
You may need to Replace Your Timing Belt if you don't fix it putting it in tension.
Timing belt slipping off can badly damage valves, causing a damage that requires an expensive repair, do not circulate if timing belt is not OK, see :Cost estimate for valve job after timing belt slip

Jul 28, 2008 | 1998 Lincoln Town Car

1 Answer

1992 Subaru timing belt parts


The key way that the sprocket rides on that obviously fell out. the key way holds the sprocket in place. You can get another key way at you NAPA store or the dealer. Re-set your timing marks and install the keyway and re-install the sprocket.

Jun 21, 2008 | 1992 Subaru Legacy

Not finding what you are looking for?
1999 Daewoo Lanos Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8575 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...