Question about 1994 Toyota Camry

1 Answer

Thermostat cover the part that is broken is the male side where the screw goes

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 979 Answers

Okay, so is it the side of the thermostat housing that's broken, or is the screw "stripped"?

Posted on Dec 17, 2008

  • Michael Borelli Dec 17, 2008

    Alright then, what you'll have to do is acquire a new housing as it's virtually impossible to repair one of those castings. I'm sorry.


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer


Remove screws from bottom of the cover. Then the tricky part......the upper cover. It has a little tiny screw on the right hand side (stereo side) under the cover holding it down. I find that a 3mm or 4mm socket will take it out. It's a male star head, so opposite of torx.

Feb 16, 2014 | 2002 GMC Envoy

1 Answer

How to remove inner door panel on a 1999 dodge caravan

Almost all door panels are attached by:
SMALL PHILLIPS HEAD SCREWS- these are found all around the door panel. They are normally hidden by; small plastic grommets (round, flat plastic push tabs used to cover and make it look pretty!)
-remove with flat head screwdriver or your nails at-own risk,
-easily popped off by squeezing outer edges inwards releasing the male part on the speaker cover from the slot on the door panel
THE RUBBER OR PLASTIC COVER- found on the inner side of the door handle
-this cover may not be there for your model and you may see the screw or the grommet. If not, remove cover with flat head screw driver or needle nose plyers, then remove screw/s

1)check for grommets if screw/s are not in plain sight)- plastic push tabs (flat head and round about a 1/4 to a 1/2 inch in diameter, normally matches the car door panel and fits flush with the panel as well so look closely! You will need a flat head screw driver for this part or try your nails at own risk.),

2) Once you have removed all the screws and or push tabs shake the panel to pin point any remaining screws or tabs. Some times there are slots in the door frame that join with the male part located on the inner side (touches the door) of the plastic panel.

good luck!

Feb 10, 2012 | 1999 Dodge Grand Caravan

1 Answer

How to remove top plate on steering column the flasher switch is on top and to fix the problem i have to remove the steering column. i can not get the top of the steering column off.

there are a couple of screws that hold the lower part of the cover to the upper part. Remove those and remove the lower cover. There will then be two male torx screws that hold the upper cover in place just behind the steering wheel (look up under the column and you should see them on either side of the column). Once those two are removed the upper cover will come off.

Nov 09, 2011 | 1997 GMC Sonoma

1 Answer

Ignition switch pontiac

I am not sure of the correct tool name but it is a female torx with a male pin in the center. You have to remove the cover, and then you should see the screws on the left side, not the ignition cylinder side,. I had to change one from a pontiac grand prix and I had to go buy a set of the male/female torx to change it. After I changed it, I changed the screws to phillips so if the ignition switch needed changed again, I only needed a screw driver.

Apr 05, 2010 | 1991 Pontiac Trans Sport

1 Answer

Licence plate falling off

why not drill to seperate holes and put self tapping bolts in to hold it on simple fix

Mar 05, 2010 | 2003 Nissan Murano

1 Answer

Passenger side map light won't work even after bulb replacement?

There is a little plastic cover that hides two mounting screws where the arm goes into the headliner. Pop that cover off and remove the screws. Pull the arm down until you can see the wires that run through the are. Make sure the connector is still connected and look to see if the wires are broken. If not, the wires could be broken in the sunvisor.

Nov 28, 2008 | 2005 Honda Accord

Not finding what you are looking for?
1994 Toyota Camry Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6864 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides