Question about 2007 Chevrolet Silverado 1500 2WD

1 Answer

Chevy engine screws

Where can i find engine screws for chevy engine

Posted by on

  • Anonymous Dec 25, 2008

    the screws for the throttle body its 4 of them that hold it on

  • s60six May 11, 2010

    what screws are you looking for?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 59 Answers

Chevy dealership

Posted on Mar 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to adjust a Quadra jet carberator on a small block Chevy.


Hello, It's been a long time since I have adjusted a Quadra Jet. Start the engine and bring it up to running temperature. Make sure the choke is fully off. At idle , turn the right hand idle mixture screw in until you hear or feel the engine start to miss. Back out the idle mixture screw 1/4 turn. Repeat procedure for the left hand idle mixture screw. Adjust idle speed screw to 800 RPM for auto trans in gear or 700 rpm manual trans in neutral.

Oct 28, 2015 | Cars & Trucks

Tip

Small Block Chevy V8 267, 305, 327, 350, 400 cid.


Bolts or Parts Lube or Sealer Torque to: 7/16 Main Caps (2 bolt) Engine Oil 70 ft-lbs. 7/16 Inner Main Caps (4 bolt) Engine Oil 70 ft-lbs. 7/16 Outer Main Caps (4 bolt) Engine Oil 65 ft-lbs. 3/8 Outer Main Caps (4 bolt) Engine Oil 40 ft-lbs. 18436572 The firing order Small Block Chevy V8 3/8 Connecting Rod Bolt Engine Oil 45 ft-lbs. 11/32 Connecting Rod Bolt Engine Oil 35 ft-lbs. Cylinder Heads
Engine oil
(blind hole)Sealer
(water jacket)
65 ft-lbs.
Rocker Studs (screw-in) Engine Oil 50 ft-lbs. Oil Pump Engine Oil 65 ft-lbs. Oil Pan Engine Oil 12 ft-lbs. Cam Sprocket (upper gear) Thread Locker 20 ft-lbs. Timing Cover Engine Oil 6 ft-lbs. Intake Manifold
(Cast Iron Heads)
Non- Hardening Sealer 30 ft-lbs. Valve Cover Engine Oil 3 ft-lbs. Exhaust Manifold Anti-Seize Lubricant 25 ft-lbs. Spark Plugs No Lube or Sealer 20 ft-lbs. Flex plate (Automatic)
Flywheel (Clutch)
Thread Locker 60 ft-lbs. Clutch Pressure Plate Thread Locker 35 ft-lbs. Center bolt
(Harmonic Damper)
Engine Oil 60 ft-lbs. Bell housing
(Transmission to Block)
Engine Oil
  • 25 ft-lbs.

on Jul 17, 2010 | 1985 Chevrolet Chevy

1 Answer

Replacing 1987 Chevy Nova Thermostat


Look for a hose extending from the top of the radiator to a round housing atop the engine. Removal of the housing cap screws will reveal the thermostat. Note the mounting orientation of the thermostat to avoid installing the replacement upside down. Remove the old thermostat and gasket. You may have to scrape the old gasket off. Place the replacement gasket and thermostat in position and reinstall the housing cap screws and tighten securely. Start your Chevy and check for leaks..

Jan 09, 2014 | 1987 Chevrolet Nova

1 Answer

Adjusting the idel for a 1985 chevy van 308 engine with 4bbl carb


There should be a base idle screw and the idle speed control motor.
There is also a fast idle screw on the opposite side for the choke.

Jul 03, 2012 | Chevrolet G10 Cars & Trucks

1 Answer

What size and type of screws are in the dashboard extension on the engine cover for a 2000 chevy astro van?


Small screws are 7mm, 8mm, and some are 9/32", and 7/32". The doghouse has 2 15mm screws way up in there, on the left top and right top.

Feb 05, 2011 | Chevrolet Astro Cars & Trucks

2 Answers

Where is the knock cylinder located on a 1990 chevy c1500 V8


It is located in the side of the engine block on the passenger side of engine down low, it screws into the water jacket so be prepared to get wet.

Jan 30, 2011 | 1990 Chevrolet C1500

1 Answer

How to repalce heater fan blower motor on 85 chevy dooly with a diesel engine


THE HEATER FAN IS LOCATED UNDER THE HOOD ON THE PASSANGER SIDE FIRE WALL. IT SHOULD JUST BE HELD IN WITH FOUR SCREWS AND IT WILL HAVE ITS POWER SUPPLY WIRE CONNECTED. DISCONNECT POWER SUPPLY AND REMOVE THE FOUR SCREWS AND THE FAN SHOULD JUST PULL STRAIT OUT.

Dec 11, 2010 | 1985 Chevrolet Chevy

1 Answer

How do you set a 4 barrel carb for a 305 chevy.


You will have to make sure the mixture screws are not blocked with a plug,if they are the carb,will have to be removed and the plugs taken out,but the mixture screws can be turned all the way in,with engine off.Then turn both mixture screws out two and a half turns,then start the engine ,and allow the engine to warm up to normal operating temp.Now,turning the mixture screw on the drivers side out,or in just a fraction at a time until the engine smooths out to the best running possible,then move to the other side and do the same.

Sep 11, 2010 | Chevrolet Caprice Classic Cars & Trucks

1 Answer

Trying to replace headlamps in 1994 Chevy 1500 (5.7L V8 4x4). No clue how to get in there. Any ideas?


I don't know your chevy specifically but there are only two ways. Either in the engine compartment or a couple of screws on the outside hold the lens. Remove and you can change bulbs. You can always call your Chevy dealer and ask service advisor. They should be willing to help you otherwise you may buy a Ford. Good luck!

Mar 10, 2010 | 1994 Chevrolet C1500

1 Answer

Removing evaporator in 93 chevy pickup


Did you connect the lines? and did you break loose the tar that holds itto the car and seals the holes for the pipe? You maya have to remove the outter core cover to getto the last screws to get it out.

Jul 18, 2009 | 1996 Chevrolet K1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

63990 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...