Question about 1995 Dodge Stratus

1 Answer

2000 Dodge Sratus 4 speed auto transmission

Transmission will not shift from low. Code reader gives 2 codes p0700 and p0755 transmission control system and shift solenoid "B" the code reader gives the freeze frame on the p0755. Is the p0700 code representing the trans. elec. system if so does this meen that the p0755 shift solenoid "B" the problem

Posted by on

  • 1 more comment 
  • Anonymous Mar 15, 2014

    will not shift on its own from 2nd to drive it has a 4r70w transmission

  • Anonymous Mar 15, 2014

    location for transmission shift solenoid 2005 dodge dakota

  • Anonymous Mar 17, 2014

    what is the problem ? what part needs to be replaced ? Whats the part numbers ?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 3 Answers

Dave, The P0700 code is a generic fault code indicating the the TCM (transmission control module) has recognized a problem and the P0755 is the indicated problem. I'd recommend you check your transmission external electrical connector for water intrusion and corrosion at the terminals by disconnecting the connector. If nothing appears wrong, I'd then recommend you drop the lower transmission pan and take a look at the residue deposit that is laying on the bottom of the pan. You should only see a relativily minor amount of grayish, black clutch material residing there. Pay particular attention for a gross amount of this or any large particular material, including any metal, either filings or chunks, or any brass or aluminum. If this checks out to be fairly clean, then I'd recommend you replace that "B" solenoid (2-3 shift solenoid) and have the trans. pan and filter replaced.; I'd also highly recommend you have the trans flushed for anyother particular matter that may reside internally inside the transmission. You'll have to have the codes cleared and the transmission relearned for shift feel, at that point.

Posted on Jan 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P0700: what is the transmission controller?


from your statement you are going about the codes the wrong way
you take the car in to a shop that has a scanner ( autozone or the like )and the scanner reads out the codes
Then you determine what those codes refer to and fix them
code p 0700 refers to transmission control module(TCM)/mil---malfunction ===causes wiring---TCM
code p 0755 refers to shift solenoid (SS) B--circuit malfunction===causes --wiring---shift solenoid --ECM/TCM
code p 0300 is random misfiring and the last number of that code p 0301,2,3,4,5,6,7,8 is the cylinder that is misfiring

Mar 24, 2017 | Cars & Trucks

2 Answers

2006 Dodge stratus code p0700


code p0700 refers to transmission control system/ mil--malfunction===causes--wiring--TCM
check all wiring and connections to the transmission for water,corrosion etc
check/change the tcm ( transmission control module)

Apr 23, 2015 | 2006 Dodge Stratus

3 Answers

How can I fix my 2004 Dodge Stratus w ith Fault code P0700


Dodge is quirky about voltage, and transmission(DC-PO700) shift selonoids are electronically controlled actuators and your PO622 Diagnostic Code is usually found with voltage irregularity such Wave,Ripple,or square voltage issues(indications that your about to have alternator or battery failure..I would try a new battery and have my alternator checked if codes persist. Best Wishes & Happy Motoring!

Jan 21, 2015 | 2004 Dodge Stratus

1 Answer

What does diagnostic code PO0706 and PO700 mean?


OBD II Fault Code
  • OBD II P0706
Fault Code Definition
  • Transmission Range Sensor Circuit Range/Performance
The purpose of the automatic transmission is to match the engine's optimum power and torque characteristics to the driver's desired rate of acceleration and speed by auto-selecting different gear ratios or 'speeds' to power the wheels. The Transmission Range Sensor (also referred to as the PRNDL input and/or neutral safety switch) tells the transmission control module (TCM) and the powertrain control module (PCM) that the transmission is in park, reverse, neutral, drive, low, 2nd, 3rd etc. It is attached directly to the manual valve of transmission, so when the shift lever is moved say from park to drive, the Transmission Range Sensor communicates this critical information to the above mentioned vehicle computer systems.

P0700
Many vehicles have a control module for the automatic transmission called a transmission control module (TCM). The engine control module (ECM) communicates with the TCM to monitor the automatic transmission for faults. If the TCM detects a fault in the automatic transmission and sets a transmission related fault code, the ECM is informed of this also and sets a P0700 in the ECM memory.

May 18, 2013 | 2000 Honda Civic

2 Answers

Codes P1782, P0755, and P0700


P1782 DODGE - 2/4-OD Pressure Switch Circuitxicon.jpghttp://engine-codes.com/p1782_dodge.htmlForum CodePossible causes- Low transmission fluid level
- Dirty transmission fluid
- Faulty 2/4-OD Pressure Switch
- 2/4-OD Pressure switch poor electrical connection
- 2/4-OD Pressure switch circuit is open or shorted
Symptoms- Engine Light ON (or Service Engine Soon Warning Light)
- Transmission shift shockP1782 DODGE Description The pressure 2/4-OD Pressure Switch is part of the pressure switch of the transmission. The pressure switch are located in the solenoid assembly. The switch provide input information to the Transmission Control Module (TCM). The switch will inform to the TCM is pressure exist in a specified hydraulic circuit. the TCM uses this information to verified that the solenoids are working or not.
P0755 DODGE - 2/4 Solenoid Circuitxicon.jpghttp://engine-codes.com/p0755_dodge.htmlForum CodePossible causes- Low transmission fluid level
- Dirty transmission fluid
- Faulty 2/4 solenoid valve
- 2/4 solenoid valve harness is open or shorted
- 2/4 solenoid valve circuit poor electrical connection
P0700 DODGE - Transaxle Control System Malfunctionxicon.jpghttp://engine-codes.com/p0700_dodge.htmlForum CodePossible causes- Shorted or open circuit within transmission control module (TCM)
- Failure of transaxle control module Tech notes Since the P0700 is just and informative code, check the TCM for more codes to resolve the problem.
Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Driveability problems
- Transaxle shifting problems

Jul 26, 2012 | Plymouth Breeze Cars & Trucks

1 Answer

Put trans in works great but has a code po 0700


P0700 is a generic fault code indicating a transmission problem. It's possible it's a left over code from the bad transmission you replaced. You may need to have the code cleared at a transmission shop that uses a different code reader to clear the code. Unfortunately, unlike the standard OBDII code reader, the transmission codes don't always reset themselves after a repair is made.

Oct 13, 2011 | 2000 Jeep Cherokee

3 Answers

What does these codes mean P1781, P0731, P1784 AND P0700 AND HOW DO I FIX THEM.


p1781 is manufacturer control transmission, p0731 is gear 1 ratio incorrect, p1784 is manufacturer control transmission, p0700 is trans, control system malfunction. all of these codes refer to tranny.This code normally points to a faulty transmission control module, but this is an expensive part and you should have an experienced Dodge technician diagnose the problem first. or a transmission specialist. the other codes are probably associated with the p0700 code. have a good day !

Apr 27, 2011 | 2001 Dodge Grand Caravan

2 Answers

P0700, P0750 and P0755 codes I was driving at 65 mph and the 2003 Dodge Caravan down shifter to low gear and the check engine light came on. It will not ship to high gear.


P0700 (M)
Check Transmission DTC's
This code indicates that the EATX (Transmission controller) has an active fault and has illuminated the MIL via a BUS message. The specific fault must be acquired from the EATX via a DRBIII tool. (Input or Output Speed Sensor failures often cause this code and are a common failure part on WJ Grand Cherokees

P0750
Shift Solenoid circuit.
Note: If code P1767 (Transmission Relay Always On) is also present: Replace transmission solenoid assembly. See note provided. When transmission is in limp mode the relay that provides power to the solenoid group is switched off. This is normal and is designed to provide operation in one gear only. Engineering department suggests to replace transmission solenoid assembly anytime these two trouble codes occur together. See applicable service manual section (21) for solenoid assembly replacement directions. IMPORTANT: When performing this repair always check torque on all valvebody accumulator cover plate screws. Proper torque specification is 70 inch pounds. If any accumulator cover plate screws are damaged or missing replace the valvebody assembly. NOTE: If any other trouble codes are present do not replace solenoid assembly. See test in the applicable Transmission Diagnostic Procedures Manual

P0755
Shift Solenoid B

Oct 14, 2009 | 2003 Dodge Caravan

1 Answer

Engine light came on, doesn't up-shift


The transmission is in limp in mode. The check engine light is on because the transmission controller told the engine controller to turn it on. You will have to get the fault codes checked to diagnose the problem. Expect to find a P0700 code in the engine controller. Thats the code for a transmission fault in the trans controller. It could be as simple as an input speed sensor or as complexed as an internal failure. Either way have the transmission fault codes checked for a proper diagnosis.

May 15, 2009 | 2004 Dodge Dakota

2 Answers

Check Engine light on and transmission will not shift from low.


Did they erase them by any chance? 2 out of the 3 come up transmission related. Does it feel likes it shifting funny or hard or anything? Not sure if unhooking battery will work on that year or not but worth a try if vehicle seems to shift fine. Then if codes come back, have it checked and repaired at that time, it may be a simple update needed to computer.

Jan 02, 2009 | 2000 Dodge Caravan

Not finding what you are looking for?
1995 Dodge Stratus Logo

1,229 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6869 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...