Question about 1997 Honda Civic

1 Answer

How do you remove the front axle on a 1997 honda civic?

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Where is the location of the coolent temp sensoron a 98 sts

Posted on Dec 16, 2008

  • raymaya Dec 16, 2008

    where is the location of the coolent temp sensor on a 1998 caddy sts



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Whats the easiest way to replace a cv axle on a 1997 honda civic

There is only one way to change a c/v joint, no such thing asan easy way to do a job cprrectly

Jul 24, 2015 | Honda Cars & Trucks

1 Answer

How to remove front axle

It doesn't have an axle

Jul 12, 2014 | 1995 Honda Civic

1 Answer

How do I replace the front wheel bearing in a 2001 Honda Civic? What special tools are required?

The Civic is a front wheel drive car: It does not have a bearing on the front wheels. Your car is equipped with a transaxle and drive axles that go into the transaxle. There are two CV (constant velocity) joints on each axle: an inner and an outer joint. If you want to pull the hub off of the drive axle or pull the drive axles, you will have to do a lot of other things first. If you still want the pull the hub, respond and I'll tell you how. It is an involved process and I don't want to waste your time with details that are not necessary.

Nov 23, 2010 | 2001 Honda Civic

1 Answer

How do i change the two front cv joint axles on a 1991 honda civic si hatchback?

take out the bolts that hold the struts ***. to the spindles. tie rod loose -brake caliper off pull out off way after taking nut off at the end of axle. pry bar pop axle out of trans.

Nov 12, 2010 | 1991 Honda Civic

1 Answer

How do i remove a front axle spindle nut off my 2001 honda civic lx

Unstake the nut and turn left, a impact wrench is needed, be sure to torque the nut when putting it back together, 135 ft lbs.

Feb 05, 2010 | 2001 Honda Civic

2 Answers

Replace 1997 civic ex alternator

The alternator is removed from the bottom of the vehicle. place the vehicle on jackstands positioned on the body, so the suspension hangs (you'll need this extra clearance to get the alternator past the axle shaft). 1). Disconnect the battery 2.) remove the upper mounting bolt (12mm) 3.) remove the terminal nut from the white wire. (10mm) 4.) Disconnect the 4pin connector 5.) From under the vehicle remove the lower mounting through bolt nut and through bolt (14mm) 6.) Remove the alternator from the lower mount and position the alternator to the side of the lower mount. 7.) remove the two lower mount bolts (14mm) and remove the lower mount asy. 8.) remove the alternator down the axle and out below the wheelwell. its going to be a tight fit so you'll have to turn the alternator at just the right position to get it out.

Jan 09, 2010 | 1997 Honda Civic

2 Answers

How to remove transmission on 97 honda civic dx

remove crossmember, axles, cables, tranny mount bolts (3), tranny to engine of course bolts

Go to and register for full free online repair manual

Sep 11, 2009 | 1997 Honda Civic

1 Answer

2002 Honda Civic LX Front Lower Ball Joint Removal/Install.

I had a question i bought a used control arm for a 2001 honda civic compared it to the original and everything was the same except the part where the ball joint goes into is a few mm thicker on the control arm. Beedless to say i got it in but i had to over tighten to get the nut in all the way. I thought this would stop the rattling sound when i hit a pothole bit its still doing it and i fear the control arm is the incorrect one what other honda has the same control arm as the civic?

Jun 25, 2009 | 2002 Honda Civic

1 Answer

Take out a 95 honda civic EX coupe engine

Remove the large nut on the end of the axle. Remove the outer tie rod end. Remove the upper spindle mount. There is a cover over the bolt. Remove the brake caliper and the lower ball joint and disconnect speed sensor if equipped. Remove spindle and pull the axle out. You may need a large flat head screw driver to pop the sxle out of the transaxle.

Jun 14, 2008 | 1995 Honda Civic

Not finding what you are looking for?
1997 Honda Civic Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts


Level 3 Expert

83514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22393 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides