Question about 2000 Daewoo Lanos

2 Answers

Daewoo lanos timing belt replacement how? - 2000 Daewoo Lanos

Posted by on

  • aefyy098 Apr 29, 2013

    How much power to strengthen the bolt measures 17 millimeters of belt cogwheel of the crankshaft timing of Daewoo lanos 2001 model 1500

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Daewoo Master
  • 61,252 Answers

Required tools:
13mm open end wrench 10mm shallow and deep socket 8mm socket long flathead screwdriver 17mm deep socket T50 torx socket 1/4", 3/8ths and 1/2" ratchets and extensions E10 inverted torx sockets 6mm Allen wrench 15mm open end wrench 7mm socket 12mm open end wrench 14mm socket 12mm socket 8mm, 9mm and 10mm Allen head sockets 19mm socket pry bar needle nose pliers
If you are doing this because your timing belt broke you will also need to buy a complete cylinder head, head gasket set, and both idler pulleys. ALL DAEWOO MODELS WILL BREAK THE INTAKE AND EXHAUST VALVES WHEN THE TIMING BELT BREAKS.
Start by removing the air cleaner assembly from the throttle body, remove the air filter and housing jack up the vehicle and remove the wheel, remove the plastic shielding in front of the accessory drive belt assembly, remove the accessory drive belt, place a jack with a block of wood on top underneath the engine oil pan remove the front engine mount, remove the crank shaft pulley ( the 4 Allen head bolts only not the 17mm bolt in the center.) remove the metal plate behind the engine mount bracket on the engine, remove the plastic timing belt cover 3 clips on top 2 10mm bolts on bottom. Rotate the engine until the #1 cyl. is at Top Dead Center on the compression stroke or line up the crankshaft timing mark with the mark on the inner timing belt cover ( notch in cover with notch in pulley) on the camshaft pulleys -- ( intake cam line up the line on the pulley with the line on the inner cover)( exhaust cam line up the arrow on the pulley with the arrow on the inner cover) loosen the 13mm bolt in the belt tensioner and using the Allen wrench rotate the tab until there is slack in the belt. Remove the belt. At this time I would recommend you replace the water pump, both plastic idler pulleys as they tend to overheat and lockup, and the belt tensioner. Make sure all your marks are lined up, you may need a helper to hold the Exhaust Cam in place as it tends to move during belt installation. Put the timing belt underneath the crankshaft pulley, install the belt leaving the intake cam for last and NO BELT SLACK on the right side between the crank and the exhaust cam. Once the belt is installed rotate the crankshaft over 2 revolutions and make sure is rotates freely, and your timing marks are aligned perfectly if not the engine will not run properly, tension the belt as needed. Installation is the same as removal.

To clarify, on the DOHC engine, the intake cam gear has a line on it, and the exhaust cam gear has an arrow on it. These should be lined up with the corresponding line and arrow on the VALVE COVER, pointing straight up. I just went through this process over the weekend, and spent quite a bit of time looking for these marking as I had removed the valve cover. Once I found them, it was plain and simple.
In addition, be sure to not over tighten the belt when reinstalling. The tensioner has markings on it for "old" and "new". DO NOT adjust past "new", as the car will sound like a jet engine, and the belt will not last for very long.
One more item that you may as well replace while you are in there is the cam position sensor if you have not already, as there have been issues with them, and the timing housing has to be opened to get to it

Posted on Dec 18, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How much power to strengthen the bolt measures 17 millimeters of belt cogwheel of the crankshaft timing of Daewoo lanos 2001 model 1500

Posted on Apr 29, 2013

5 Suggested Answers

  • 56 Answers

SOURCE: !999 Daewoo Lanos

try getting a chilton's repair manual for your particular car. if you have never done a timing belt before, don't attempt as you can cause severe engine damage if you don't time it correctly, and then try starting it....ie bent valves... costly repairs.

Posted on Oct 13, 2008

chiquititas
  • 1010 Answers

SOURCE: i need to put a timing belt on a daewwoo lanos

Go to mechanic and ask him to put a new timing belt, its the aftest way.

Posted on Jun 17, 2008

SOURCE: 2002 Daewoo Lanos Engine Type

Yes, this is an interference engine. I just finished fixing mine and it is a big expensive job. Sorry to give bad news.

Posted on Oct 04, 2008

greg_margo
  • 1959 Answers

SOURCE: TIMING BELT REPLACEMENT FOR 2000 DAEWOO LANOS

I found a few, most running over $100, this link has the equivalent tool costing much less. I 'll leave both links and you can choose. Best of luck on your repair.
http://www.denlorstools.com/home/dt1/page_13788_520/sealey_vs090_daewoo_water_pumptiming_belt_tool.html

http://www.etoolcart.com/browseproducts/Daewoo-Timing-Belt-Adajuster-J-42492-A.html

Posted on May 09, 2009

  • 7 Answers

SOURCE: How to replace front wheel bearings on 2000 Daewoo Lanos

they come as a whole assembly hub and all

Posted on Jan 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change a timing belt on a 2000 daewoo lanos 1.4 e tec


If this is an "interference" engine and the belt broke while running you may have major engine damage. If non-interference, buy shop manual to give all details and torque values for this very important procedure.

Feb 09, 2015 | 2000 Daewoo Lanos

1 Answer

Water pump daewoo lanos


  1. lets face it if your replacing the water pump you may as well shout it a timing belt kit at the same time as you will already be there to do the water pump and at least then with any luck you wont be back there for 90000klm when the next t belt is due.it may cost alittle bit now but it is better than overheating due to coolant leak or t belt failure because the tension had been altered in the water pump replacement procedure. either one of those things happen and you will be doing all of the above with more work and expense involved . preventive maintainance .

May 04, 2014 | 2000 Daewoo Lanos

3 Answers

I have a 1997 daewoo lanos1.5l single over head cam and broke the timing belt then the engine stalled so i replaced belt and set the timing marks. every thing was correct when set the crankshaft was top...


hi, just letting you know my timing belt just went on my daewoo lanos. unfortunately it seems in a daewoo lanos that when the timing belt goes, it can do damage to one of the valves. mine is in at the mechanics and i am still hoping that it hasnt done any damage. i was also told that if you have replaced the timing belt and the car still wont start it has definitely done damage to a valve. sorry to give you the bad news!!

Sep 05, 2010 | 1999 Daewoo Lanos

1 Answer

Engine timing belt 1600 daewoo lanos


It connects the crankshaft to the camshaft, which controls the valves that let the air fuel mix in and the exhaust out of the cylinders

Apr 14, 2010 | 2000 Daewoo Lanos

1 Answer

TIMING BELT REPLACEMENT FOR 2000 DAEWOO LANOS


I found a few, most running over $100, this link has the equivalent tool costing much less. I 'll leave both links and you can choose. Best of luck on your repair.
http://www.denlorstools.com/home/dt1/page_13788_520/sealey_vs090_daewoo_water_pumptiming_belt_tool.html

http://www.etoolcart.com/browseproducts/Daewoo-Timing-Belt-Adajuster-J-42492-A.html

May 09, 2009 | 2000 Daewoo Lanos

1 Answer

Remove and replace timming belt on lanos sx 1598cc 1998 thank you


First remove head and fix the bent valves. I have worked at a Daewoo dealer. People would buy the belt and come right back to get valves and gaskets. Daewoo timing belts must be replaced every 60,000 miles.

Apr 18, 2009 | 1999 Daewoo Lanos

1 Answer

Replaced timing belt not running right


The Lanos engine are an interference engine. If you have bent valves, remove a plug wire one at a time and see if there is no change in the idle. My guess, one of them isn't going to change anything. That would be the cylinder that has the bent valves in. I had a Lanos in my shop with a broken timing belt and the head had several bent valves. I wouldn't be surprised at all if you also have bent valves.

Jan 29, 2009 | 1999 Daewoo Lanos

2 Answers

!999 Daewoo Lanos


201b665.jpege046938.jpeg

It verifies well the year, it is of one of 1999

I hope that it should serve you

Aug 02, 2008 | 1999 Daewoo Lanos

1 Answer

I need to put a timing belt on a daewwoo lanos


Go to mechanic and ask him to put a new timing belt, its the aftest way.

May 19, 2008 | 1999 Daewoo Lanos

Not finding what you are looking for?
2000 Daewoo Lanos Logo

6,015 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

61249 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...