Question about 1998 Chevrolet Cavalier

1 Answer

1992 BMW 325 i 6 CYLINDER 4 DOOR PROBLEM: CLUTCH PEDAL WONT SPRING BACK

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 740 Answers

BAD SLAVE CYLINDER. Good Luck

Posted on Dec 16, 2008

2 Suggested Answers

  • 740 Answers

SOURCE: My Clutch pedal wont spring back

Bad Slave cylinder

Posted on Dec 16, 2008

emissionwiz
  • 61168 Answers

SOURCE: CLUTCH PEDAL WON'T SPRING BACK

Your hydraulic clutch has failed, either the master or slave cylinder, It is recommended they be replaced as a pair.

Posted on Dec 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hello I have a 1992 ford escort that I bought new. over the years you had to really push hard on the clutch pedal to get the engine to crank espectlly when it is cold out side. well today its very cold...


HYDRAULIC SYSTEM BLEEDING
  1. Check that the brake master cylinder is at least 3?4 full during the entire bleeding process.
  2. Remove the bleeder screw cap from the clutch slave cylinder and attach a hose to the bleeder screw. Place the other end of the hose into a container to catch the fluid.
  3. Have an assistant slowly pump the clutch pedal several times and then hold the clutch pedal down.
  4. Loosen the bleeder screw to release the fluid and air. Tighten the bleeder screw.
  5. Repeat the bleeding procedure until no more air bubbles are seen in the fluid.
  6. Tighten the bleeder screw to 52-78 inch lbs. (6-9 Nm).
  7. Top off the brake master cylinder to the full line.
  8. Check for proper clutch system operation. Fig. 1: Attach a hose to the bleeder screw and place the other end of the hose into a container to catch the fluid - 1991-96 model shown 90987g40.gif
prev.gif next.gif

Dec 18, 2010 | 1992 Ford Escort 4 Door

1 Answer

Clutch pedal will depress but will noy spring back??


POSSIBLE CAUSES TO YOUR CLUTCH PEDAL PROBLEM. COULD BE BRAKE FLUID LEVEL LOW CAUSING YOU TO GET AIR IN THE HYDRALIC SYSTEM.IF FLUID WAS LOW CHECK FOR FLUID LEAKS AROUND LINES TO CLUTCH MASTER CYLINDER AND CLUTCH SLAVE CYLINDER.IF FLUID LEVEL ALL GOOD. LOOK FOR A BROKE CLUTCH RELEASE BEARING OR FORK.CHECK FOR BROKEN DIAPHRAGM SPRING IN CLUTCH PRESSURE PLATE.

Dec 02, 2010 | 1996 BMW 318

1 Answer

Clutch pedal is sometimes loose and then has to be pumped. What is the cause of the problem?


hey there there
there could be a few problems there
the clutch slave
master cylinder
or the cylinde needs bleeding

Oct 17, 2010 | 2003 BMW 325

1 Answer

How do u blead a clutch in a 1992 ford escort 1.8


ani_caut.gif CAUTION: Be careful not to spill clutch fluid onto a painted surface.
  1. Remove the bleeder cap from the slave cylinder and attach a vinyl hose to the bleeder screw.
  1. Place the other end of the hose in a container.
  1. Slowly pump the clutch pedal several times.
  1. With the clutch pedal depressed, loosen the bleeder screw to release the fluid and air.
  1. Tighten the slave cylinder bleeder screw.
  1. Repeat steps 3 through 5 until no air bubbles appear in the fluid.
  1. Tighten the slave cylinder bleeder screw to 6-9 Nm (52-78 lb-in).

5833316.gif

Jun 05, 2010 | 1992 Ford Escort 4 Door

1 Answer

Clutch hydraulics on my BMW problem - quick fix. I went to use my 1992 318 BMW after not using it for a week and the clutch pedal had no pressure. The AA couldn't fix it so they towed it to my nearest...


THEY PUT IN NEW FLUID AND BLEED AIR OUT OF THE SLAVE MASTERCYLINDER.IF THE CLUTCH PEDAL GOES TO FLOOR AGAIN.YOU HAVE A LEAK AT CLUTCH MASTER CYLINDER.OR THE MASTER CYLINDER IT SELF GOING BAD.

Mar 08, 2010 | BMW 318 Cars & Trucks

2 Answers

Clutch went to floor like nuthing was attached to it... runs fine just seems that the clutch pedal dont work or something it just floppy now...it happened when i was moving it in driveway was fine before...


There is a return spring that lifts the clutch pedal back to the original position. It seems that the clutch return spring has got disconnected. The pedal will do its job of disengaging the engine from the gear box, but will not offer any resistance to the foot and thus give an impression of doing nothing. So, that spring should be set right. For this the clutch housing will have to be opened and the spring reset.

Feb 10, 2010 | 1994 BMW 3 Series

1 Answer

My clutch pedal wont spring back once i've released it. I've replaced the clutch, clutch fork & clips, throw-out bearing, clutch master cylinder, and even a slave cylinder. On top of all that, i've...


A clutch pedal not springing back is almost always an indication that there is air in the system. Bleeding out a clutch is a tedious endeavor to say the least.
I suggest you open up the bleeder screw & gravity bleed the clutch.(This will take a long time as well!)

Nov 29, 2009 | Toyota Celica Cars & Trucks

1 Answer

CLUTCH PEDAL WON'T SPRING BACK


Your hydraulic clutch has failed, either the master or slave cylinder, It is recommended they be replaced as a pair.

Dec 16, 2008 | 1998 Chevrolet Cavalier

Not finding what you are looking for?
1998 Chevrolet Cavalier Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...