Question about 2000 Ford Ranger SuperCab

1 Answer

Stuck in 4x4 Low

I left my 2000 Ford Ranger running as I went into a store because it was -12f outside, came out, put it in Drive and it also automatically jumped from 4x4 Hi to 4x4 Lo. No matter what I turned the dash switch to, the truck remained in 4x4 Lo.

Posted by on

  • 1 more comment 
  • Carl Kuyath
    Carl Kuyath Dec 16, 2008

    Thanks, it worked. I guess my new usual practice will be, after starting my truck, first putting it in neutral while continuing to apply the brakes, and checking the transfercase dash light to make sure it corresponds with the dash dial.

  • Anonymous Jan 25, 2009

    2002ford ranger stuck in 4x4 high light in dash dont light up

  • dallas233 Jan 28, 2009

    My 2000 ranger 4x$4auto will sometimes not go into 4X4 high or low, when it does it sometimes takes sometime to come out.

    Meanwhile the 4X$ low light remaines on!



    HELP

    D.M.

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 46 Answers

Put the truck in neutral and hold the brake then try to take it out

Posted on Dec 16, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 ford ranger p1121 code


Sounds like the computor has gone into limp mode. Have you heard any strange noises coming from under the hood lately ?

Feb 03, 2018 | 2000 Ford Ranger SuperCab

1 Answer

My 2006 ranger wont start. Cables seem to be fine I have lights inside and out. When I turn the key I only get clicks. I was able to jump the car and I let it run thinking the battery might be low but it...


If the jump started your vehicle and then it only ran for 2 minutes,it sounds like your alternator is not providing power to run the vehicle.

Mar 06, 2018 | 2006 Ford Ranger

1 Answer

After getting a jump-start, my entire radio/cd player went out in my 2000 ford ranger. It's a stock Ford unit. Won't come back on. Is it a fuse?


it sounds like it could be a fuse. double check in your owners manual where the fuse is located and double check if there is more than one fuse for the radio or it may have a fuse for the amplifier too.

Nov 19, 2010 | 2000 Ford Ranger SuperCab

1 Answer

2000 Ford Ranger XLT Automatic trans. 4X4 3.0L


Check your operator's manual. Make sure any and all fuses that have anything to do with the affected items are not blown and are working properly. If you can; check for loose fuse connections or wires. Hope this helps. God bless!

Nov 04, 2009 | 2000 Ford Ranger SuperCab

1 Answer

I have a 1988 ford ranger that I bought for $150. It had been sitting outside for 2 years. When I went to start it, it did satrt with jump. But once I disconnected the jumper cables it died. Did that...


First pour some gas down the intake(just a small sipp)and crank it,if it starts you have a fuel distribution problem.If it dont, there is an ignition problem.

Aug 25, 2009 | 1988 Ford Ranger

1 Answer

1987 FORD RANGER WONT START AFTER JUMP STARTING IT


to eliminate the battery or alternator: go to a parts store leave your motor running. they will come outside with the tester and test your battery and alternator free. prior to this locate where your battery cable hooks to the starter and check to make sure the nut hasnt vibrated loose (try moving the cable side-to-side). u dint specify whether the engine was turning over and wouldnt start or nothing was happening.

Jul 29, 2009 | 1987 Ford Ranger

1 Answer

Replaced wiring harness on 2000 Ford Ranger now truck won't start


2000 ford ranger wont start off switch if u jump the silanoid it will start. new start and ignition switch

May 06, 2009 | 2000 Ford Ranger SuperCab

Not finding what you are looking for?
2000 Ford Ranger SuperCab Logo

Related Topics:

381 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

82285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

gerry bissi

Level 3 Expert

4382 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...