Question about 2002 Lexus ES 300
Soemone backed into my Lexus ES300 (2002) and cracked the glass on my passenger side real light unit..Should I just replace the glass or as a friend suggested, replace the whole unit so it won't leak when it rains? Is ity hard to replace the assembly if I want t od it myself. Many thanks.
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
How does the ES 300 fit your driving style?
Conservative drivers your dream come true, Smooth, comfortable and quiet, easy to control and predictable. This car is the one to beat.
Sporty drivers Electronic throttle is very responsive, handles well for a car with such a cushy ride, Not as powerful as the other cars in this class.
Fast drivers Should opt for the Adaptive Variable Suspension. The firm setting provides this car with the character you are looking for as far as handling goes, but for all around performance, you may be happier with a Lexus IS300 or maybe an Acura TL Type S.
The answer to your question - the IS-250 is a luxury model, and the IS is sporty.
Both considered in the same CLASS of vehicle - near Luxury.
Who should buy this car? A person who is looking for a mid-sized sedan that is a cut above the average sedan in styling, comfort, luxury & performance.
Thank you for using FixYa - A FixYa rating is appreciated!!
Posted on Jan 22, 2009
I just changed the cabin filter of my ES300. I found the instructions on the manual, under airconditioning and audio. It's pretty easy to do. I bought the filter from Kragen's for $21.95.
Posted on Mar 27, 2009
After removing the top and side bolts (which are obvious) Go to the fender liner. Remove all but the top screw . You will find (by flashlight or shop light) two bolts coming out of the headlight rear. With a socket wrench and 10mm socket, remove the two nuts on the headlight and pull out the headlight from the front after insuring the bulbs are removed and identified for reinstall. Take your time. It is not difficult.
Posted on Apr 05, 2009
UNKNOWN BUT TOO REPLACE
IF YOU CAN SEE THE RADIO DON'T REPLACE IT
BUT ITS A LEXUS THE CAR IS 1 OF A KIND IT SELF BESIDES THE CRACK IN THE RADIO
GET A NEW 1 WITH BLUETOOTH by ALPINE and get yo stunt on its 2009
THE WORLD IS CRACKED NOT NAVIE GLASS
Posted on Apr 25, 2009
My Son has a 95 es300, the amp for it is located under the front passenger seat. The easiest way to access it is to remove the 4 bolts holding the seat down, and remove the seat. Takes about 5 minutes
Posted on Jul 24, 2009
Tips for a great answer:
Jan 15, 2013 | 1995 Lexus ES 300
Chevy Uplander (2005) Headlight bulb or turn signal replacement:
It is important to ensure all lights are working for the safety of you and others on the road.
In order to gain access to the head light bulbs, the headlight assembly must be removed. There no easy way to gain access to the lamps with the assembly installed. Open hood. Use 10mm wrench to remove faster on top of the light assembly closest to the rubber hood rest. You then need to remove the silver looking pin near the grill. This pin is snapped in place. Rotate counter clockwise and then pull pin straight out. The light assembly will now have to be pulled past the front header panel near the grill. Use care as the light is pulled past the grill panel. When you have this done there is one more fastener holding the light to the vehicle. On the far out side edge of the light near the fender panel, there is a ball socket fastener holding the light to the vehicle internal frame. Pull straight forward to pull the ball pin out of the socket. It will take a lot of force, but be careful as you apply force and pull light out forward. My light took some wiggling up and down, left and right until the ball released. Once the light is out, the lights are accessible. Both the normal and high beam light sockets rotate counter clockwise to remove from the headlight housing. There is a very tight detent in the counter clock rotation which took a fair amount of force. Once it "clicks" past that point during rotation, the light socket was able to be pulled from the light housing. The light bulb pulls straight out of the socket. Please use a clean towel or gloves to protect your fingers. Bulbs can sometimes crack and cut your fingers. Also, when you install the new lamps, use a towel or cloves as not to get oil on the glass which can cause uneven heating of the glass and crack it under use.
With the light assembly out, it is now easy to reach down into the vehicle to change the turn signal. This lamp is colored since the turn signal lens is clear.
Once bulbs are replaced, please test them before reassembly just in case of any issues. The headlight assembly ball socket will snap back into place easy. Once that is in, press the rest of the light back to its normal place. When the holes are lined up, please the silver colored rod back into its slots all the way down the inside of the light assembly. It then can be rotated and locked back into place. Reinstall the 10mm bolt on top of the light assembly near the rubber hood rest. Again check the lights to insure nothing is out of order.
To gain access to the bulbs to the real light assemblies, you must remove the light housings. Open up the rear hatch. Use a T30 Torex screwdriver and remove the two screws on the inside of light. Once those are out, the light assembly can be pulled out slightly from the vehicle. On the side of the van, the light assembly is held in place by two snap fasteners. Pull the light towards the rear of the vehicle to disengage the outside edge fasteners. Once done, the light assembly will be loose and the bulb sockets are accessible. They rotate counter clockwise release from the housing. The bulbs themselves pull straight out of the socket. Please use a towel to protect your hands and to make sure no oil gets on the bulb surface. Once done, reinstall the light assembly by first lining up the two plastic fasteners on the outside edge to the vehicle panel and press the light assembly to the vehicle. Reinstall the two screws and test light. Be sure to have someone press the brake for you to ensure your brake light works.
Low beam/ high beam lights: (12362LL) Phillips (H11LL)
Front Turn Signal: 4157NAK amber color
Corner marker lamp: 194FH4 clear
Brake/turn light: 4157LL (clear lamp)
Lower back up light and top running light: 3057XX (Wagner) (clear lamp)
Oct 01, 2010 | 2006 Chevrolet Equinox
Jul 24, 2010 | Lexus GS 300 Cars & Trucks
Jun 28, 2010 | 2002 Lexus RX 300
Jun 25, 2010 | 1999 Lexus Gs 300
Apr 07, 2010 | 2003 Chevrolet Silverado 2500HD
Oct 13, 2009 | 2000 Lexus RX 300
Aug 17, 2009 | 2004 GMC Envoy
May 28, 2009 | 2001 Ford Taurus
Jan 24, 2009 | 1995 Lexus ES 300
32 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: