Question about 1997 Chevrolet S-10 Pickup

1 Answer

Brake pum the brake some time ok some time dont no leake or any thing 1986 s 10

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

Master cylinder

Posted on Dec 16, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer


no brakes at all.
did you check fluid levels? yet? both went dry?
leaking DOT3 fuid, in the system, this take looking at every inch of system. or fail.

can the brake pedal be pumped up
is the pedal hard,?
dont drive it. (sorry)
here is the dont drive list, brakes can do many things wrong.

Feb 08, 2014 | 1995 Jeep Cherokee

1 Answer

A 2000 Land Rover Discovery's internal brake light indicator is flashing from time to time or staying on and wondering if the brake fluid level is ok then could it be the brake light switch needs replacing...

well, yes it could mean the fluid is low,why dont you check it.If u need help for this go no further with your own repair inquiries.. another common thing is sticky rear parking brake cables if u have drum brakes on the rear

Aug 26, 2013 | Land Rover Discovery Cars & Trucks

1 Answer

Cavalier master cylinder

You have air in your system, you need a helper to bleed the air out. The master cylinder is what ur brake fluid resivore is sitting on, the large round object behind it is the brake booster (looks like a squished basket ball) these will be on the fire wall driverside

Nov 05, 2012 | 1999 Chevrolet Cavalier

2 Answers

1988 nissan navara brake booster not working

it sounds like you have a leak someplace in the system.

Feb 09, 2018 | 1996 GMC Yukon

2 Answers

Front and rear drum brakes, the pads are ok, but the brake pedal started going to the floor. When I tried to bleed them, the rear bleeder screws broke. So I replaced both wheel cylinders. The rubber... you have stated that you have bled the brakes properly.....was there fluid coming out each bleed nipple as a flowing stream...????

And did you shut off the bleed nipple half way down stroke....?????

If this is all ok, then I would be looking at a failed master cylinder.......and what is occurring is the fluid is leaking from the primary to the secondary within the master cylinder !!!!!

Mar 31, 2011 | Ford Mustang Cars & Trucks

1 Answer

'92 Toyota Landcruiser 80 series- brake light came on in the instrument panel and remains on all the time. Brakes working ok. What's the cure?

You say the brakes work fine, so lets start with the e-brake switch,make sure swith is working and ebrake is all the way off, the next thing is the sensor in the mastercylinder, is the brake fluid low or is the sensor working,with this sensor and the ebrake sensor try unplugging and see if light goes out, start with these things first,also there are no brake fluid leaks on the ground,this would cause the poprotioning valve to turn the light on also,but lets start with the other things first. hope this helps.

Apr 06, 2010 | 1992 Toyota Land Cruiser

4 Answers

Brake fluid leaking inside car onto floor mat.

Bad Master Cylinder and or Power Brake Booster would be the first things to check.. look for signs of a leak under the hood first, monitor brake performance!!

Feb 09, 2010 | 2006 Ford Focus

2 Answers

Losing brake fluid slowly but its not leaking at the caliper.dont think its from pad wear.dont see any stains.where could it be going?

If there isn.t any leaks along the brake lines, or at any of the wheels, look under the brake master cylinder, it's bolted to the booster, ( that big black round thing) and see if it is wet right under it. if it is wet, the master cylinder is leaking, and needs replacing. The o-rings on the piston in it are probably worn, and when you put your foot on the brake, the fluid is seeping by them and leaking at the end, but not very much.

Nov 02, 2009 | 2003 Volkswagen Passat

1 Answer

I have a problem with my brakes, it's not the brakes or rotors. just sometimes the brakes go to the floor and dont stop, and other times they are amazing, sometimes even touchy. What could be my problem?

Could be two things:

Most likely master cylinder piston leak.
Rebuild / replace master cylinder ($80)

Otherwise there may be air in the brake system.
Bleed brake system ($20)

Might want to bleed first ... see what other experts recommend.

Sep 30, 2009 | 1999 Chevrolet Malibu

1 Answer

2000 grand cherokee ltd.Brake problem

You need break booster what happen is when you tern the car of the vacuum leaks out when you start the car its take time to build the vacuum that's why it does not work at first time then its come back

Apr 13, 2009 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
1997 Chevrolet S-10 Pickup Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

83096 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides