Question about 2006 Ford Mustang

1 Answer

Automatic Up for power window not working

Passenger side window works with either switch to go down or up while holding the switch. Automatic down works just fine as well, but when you close the passenger side door it will not push up to seal like it should. Also when you try to use the auto up portion of the switch it will not work. Fully push the switch down works as it should and the window goes completely down. Pull the switch up and it will only work as long as you hold the switch. Drivers side works as it should in both directions. Any idea's as to where to begin?

Posted by on

  • 2 more comments 
  • Jeff0608 Dec 16, 2008

    If it was the switch then it would only effect 1 switch no? I don't
    think that both switches would go out at once. Not totally out of the
    question but still unlikely. Also considering the auto down feature is
    still working I don't think it would be the relay since they are just
    reversing the polarity of the voltage.



    Okay problem has been fixed! It was really a simple fix that worked.
    The window apparently has a calibration built into some sort of memory.
    I did further research and found a manual located at http://www.myacrobatpdf.com/1988/ford-mu... This
    told me to run the recalibration based on the window would not go
    completely up when closing the door. I ran the window all the way down
    held the switch for 2 seconds and ran it all the way up and held the
    switch for 2 seconds. The window now works as it should.





  • Anonymous Feb 04, 2009

    I had the same problem. I followed ur instructions and it worked perfect. Thanks



  • lordpeekaboo Feb 25, 2009

    I have a similar problem but the calibration steps did not solve the problem. My window will run all the way up and then drop to about 1/4 the way up and stop. I have disconnected the battery for an hour and tried recalibration several times. Not an ideal condition in South Dakota in February.

  • Anonymous Mar 31, 2014

    all window motors and switches are good driver side window will not work using switch, and truck does not want to start unless you move the (automatic trans) gear shift around and the gages on the instrument cluster will move then it will start like a broken wire

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 328 Answers

There are relays that keep power to the window motor until it is all the way up..it sounds like there is a problem with that relay or the switch itself
hope this helps.....Good luck!

Posted on Dec 15, 2008

  • s60six Dec 21, 2008

    Glad you were able to solve it!.......the next time i see this problem ill definitely keep your solution in mind...........thanks for the update!

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Replaced battery, now auto windows wont come up auto automatically


If on a GM car the battery has been disconnect the windows may need to be reprogrammed
The following steps explain how to program the side door window regulator motors:


  1. Press and hold the power window switch until the window is fully DOWN. Continue holding the power window switch for approximately 3 seconds.

  2. Press and hold the power window switch until the window is fully UP. Continue holding the power window switch for approximately 3 seconds.

  3. The power window regulator motor is now programmed for the express function.

  4. Repeat this process for all of the power windows.

Dec 01, 2015 | Cars & Trucks

1 Answer

Passenger window switch works but the drivers side switch does not


was regulator bad? did it work from drivers side switch before you did regulator repair?..if so passenger side switch wiring has issue and is not sending signal through it back to the drivers side master switches.. otherwise you need to pin test for power up power down on drivers side switch and repair that if issue going to the window on passenger side.. (possible pinched at door jam area common)

Nov 20, 2013 | 2002 Hyundai Accent

1 Answer

Power window


Sounds like a passenger switch malfunction.

Sep 08, 2013 | 2009 Mazda CX-9

4 Answers

2006 Toyota Avalon- Changed the battery and the driver side button to roll the passenger side window down doesn't work. The remainder of the buttons work, just not that single button. The passenger side...


try going to passenger door window switch and reset it by going down and holding for extra 3to5 seconds after window is down, do same to go up, then try doing it with master switch don forget to hold it longer, this is a reset also used on Scion vehicles, hope it helps.
Good luck

Jan 09, 2011 | 2005 Toyota Avalon

4 Answers

Passenger side window stuck in down position


Volcompunker is on track.... if it is a stuck motor problem, before taking door apart, try this...it may work, works well on dodge caravans...

NO COST and fast PROCEDURE TO FIX IT:

1. Sit in vehicle, on seat next to problematic window
2. Ignition key is on
3. Door in question is opened (in case you closed it)
4. While door is open, press and hold power window button in desired window travel, keep button pressed !!
5. SLAM hard the door closed with one hand while other hand holds button as per #4.
6. Watch window operate as it should.

7. Repeat 3-6 if necessary, but usually the first try works!

Jul 11, 2010 | 2001 Ford Expedition

1 Answer

2005 Chrysler T&C passenger side window went down and won't come up. All other automatic windows and door locks work fine - don't hear any motor sound / buzz / etc. when either driver side or passenger...


If the window had not been slow in it's action before it stopped working I'm guessing you only have a connection problem. I would remove the door panel and using a multimeter check the hot wire to see if power is reaching the switch. If it is check the connection on the motor. If power is reaching the motor through the switch you have a faulty motor. If at any point of testing there is no power backtrack the power wire to find where the break is. (it's usually in the door jam)

Apr 13, 2010 | 2005 Chrysler Town & Country

1 Answer

Passenger power window stopped working???


some times the window regulators on toyotas need to be resett if they get jammed or they are interupted when operating ... an easy way to reset the regulator in toyotas is to disconnect the passenger regulator or switch wait 5 minutes the reconnect and using the passenger switch hold it up for 20 seconds and then down all the way holding it down when it stops for another 20 seconds. then check that the drivers side is now working and reset

Dec 13, 2009 | Toyota MR2 Cars & Trucks

1 Answer

Power Window on passenger side not working


It either needs a new window motor or switch. To tell which, you can open the door, have the ignition in the on positon or running, hold up or down on the window switch (whichever way it needs to go), and slam the door pretty hard while holding the switch. If the window works, it needs a motor/regulator assembly. If not, look at wiring or switch. If you can hear the motor running, and nothing happens, you need a motor/regulator assembly.

May 26, 2009 | 2006 Chrysler Sebring

3 Answers

2000 GMC Jimmy SLE driver's power window


The same thing happened to my 1999 JMC Jimmy recently. I believe the problem is that your power window motor has most likely gone out or is starting to go out. The motor will need replaced. They are pretty expensive new. I went to a junkyard and got one for around 15 dollars. When mine went bad, I had rolled my window down about three or four inches and it stuck there. I took my door panel off and tapped on the motor while holding up on the window switch and got it to go up after a few minutes. I am replacing my motor today, I'll leave an update here about the outcome when I finish the job. I hope this information helps you.

Sep 27, 2008 | 2000 GMC Jimmy

Not finding what you are looking for?
2006 Ford Mustang Logo

425 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...