Question about 1986 Mazda RX-7

1 Answer

Wiper problem, and slight bump under back in

First off, the wiper blades only work on one speed, not slow but the next step up. I think it may be the switch. Second, When I left off the gas it feels like there is something hitting the bottom of the car in the back end. I thought it was the transmission but checked that, not sure now. I can drive it where it doesn't do that but I have to ease off the clutch after switching gears.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Http://fc3spro.com/TECH/HOWTO/WIPER/wiper.htmlrelay problem.mine has gone from rear wiper working occasionally to not at all,intermitted ceased working,mist ceased working to last week 2 speed not working only 1 speed working although when switched off,blades stay where the are at that time.used to use the mist to bring them back down to bottom of screen.am now going to finally do the above once i get the relay...

Posted on Jun 05, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My 2003 chevy impala windshield wipers only work


Replace the wiper motor. It is under the wiper blades. remove the blade arms, remove the plastic bezel, remove the motor. The motor has the delay and speeds built in it.

Oct 16, 2014 | 2003 Chevrolet Impala

1 Answer

Wipers stop in the middle of my wishield,will not park properly


Sorry , no adjustment .
Wiper/Washer System Components
The Wiper / Washer System consists of the following components:
• Windshield wiper / washer switch
• Windshield wiper system module / motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR 25A fuse
Wiper / Washer System Operation
The windshield wiper motor module is part of the windshield wiper motor cover and controls the wiper motor operation. The windshield wiper motor is a 2 speed motor. Windshield wiper DELAY operation is a low speed wiper motor function with a variable delay interval between the wipe cycles. The DELAY interval is controlled through a series of resistors within the wiper / washer switch.
Park Position Operation
When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Do you know how to do diagnostic's ?

Wipers Blades Do Not Park
Step
Action
Yes
No
Schematic Reference: Wiper/Washer Schematics
Connector End View Reference: Wiper/Washer Connector End Views
DEFINITION: This table diagnoses the wipers operate normally but will not return to the park position when the wiper operation is cancelled.
1
Did you perform the Diagnostic System Check - Vehicle?
YES - Go to Step 2
NO - Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2
Turn ON the ignition, with the engine OFF.
Move the wiper switch to the LO position.
Move the wiper switch to the OFF position.
Do the front wipers advance to the park position?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Turn the ignition switch to the RUN position.
Turn the wiper switch to OFF.
Disconnect the wiper/washer switch connector.
Do the wipers park?
YES - Go to Step 7
NO - Go to Step 4
4
At the wiper/washer switch connector, measure the voltage of the windshield wiper switch signal 2 circuit.
Does the voltage measure greater than 1.0 volts?
YES - Go to Step 5
NO - Go to Step 8
5
Reconnect the wiper/washer switch connector.
Disconnect the wiper motor connector.
Measure the voltage of the windshield wiper switch signal 2 circuit.
Does the voltage measure greater than 1.0 volts?
YES - Go to Step 6
NO - Go to Step 8
6
Repair a short to battery positive voltage in the windshield wiper switch signal 2 circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
YES - Did you find and correct the condition?
NO - Go to Step 9
--
7
Replace the wiper/washer switch. Refer to Turn Signal Multifunction Switch Replacement in Steering Wheel and Column - Tilt.
YES - Did you complete the replacement?
NO - Go to Step 9
--
8
Replace the wiper motor cover. Refer to Wiper Motor Cover Replacement .
YES - Did you complete the replacement?
NO - Go to Step 9
--
9
Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 2

Jan 31, 2018 | 2005 Buick Century

2 Answers

Wind shield wipers not working


First check the fuse box under the hood for a blown or poorly connected fuse. Next, find the wires going to the wiper switch and check for power when you turn the switch on. Finally, if there is power everywhere you checked, go directly to the motor and check it for getting power. Also check the ground wires for this device. If no ground...no action!

Jan 11, 2013 | 1999 Ford Explorer

1 Answer

1998 Porsche Boxster windshiled wiper stopped working


Could be loose wiper arm. Are the blades heavy. Too big of wiper blade will cause problems

Nov 15, 2012 | 1998 Porsche Boxster

2 Answers

Vw golf mk3 wipers not working,fuse ok. sometimes work if blades assisted manually


WIPER ARM LINKAGE COULD BE BINDING.REMOVE WIPER ARM TO SEE IF WIPER MOTOR OPERATE SLOWLY.IF YES CHECK TO MAKE SURE WIPER MOTOR GETTING GOOD GROUND CONNECTIONS BY CHECKING MOVING WIRES .IF WIPER MOTOR SPEEDS UP YOU HAVE GROUND WIRE PROBLEM. IF WIPER MOTOR REMAIN SLOW GROUND WIRES CHECK OUT OKAY.REPLACE WIPER MOTOR.IF WIPER MOTOR RUN FAST NORMAL SPEED AFTER DISCONNECTING WIPER ARM.WIPER ARM LINKAGES IS BINDING OR NEED SOME LUBRICATION TRY WD40 SEE WHAT HAPPENS.LUBRICATION DONT HELP WIPER LINKAGE COULD BE DAMAGED.

Nov 18, 2010 | 2000 Volkswagen Golf

1 Answer

Is there a procedure to check the wiper motor on 1991 S10 pickup (only 42000 miles), to be sure it is defective and not a wiring problem?


ONLY PROCEDURE FOR WIPER MOTOR IS YOU HAVE 2 SPEEDS THAT WORK SLOW AND FAST SPEED.WIPERS WILL RETRACT TO THE BOTTOM OF HOOD LINE WHEN YOU TURN OFF. WIPERS SHOULD TURN OFF. CHECK WIPER RESERVOIR MAKE SURE ITS FULL AND WIPER WASHER SPRAY FLUID CLEAN WINDSHIELD. IF WIPER MOTOR DO ALL THE ABOVE THEN ITS OKAY.IF WIPER MOTOR WORKS SLOW LOOK FOR BINDING AT WIPER ARM LINKAGE AND PIVOT LUBRICATE LINKAGE AND PIVOT COULD HELP.IF WIPER MOTOR DONT WORK CHECK FOR POOR GROUND OR BLOWED FUSE.WIPER WORK AT ONE SPEED CONTROL SWITCH IS BAD.IF WIPER BLADES STOP WHERE EVER THEY ARE OR FAIL TO TURN OFF UNLESS YOU TURN OFF IGNITION SWITCH WIPER MOTOR LIMIT SWITCH BROKEN.IF WIPERS DONT RETRACT BELOW BOTTOM HOOD LINE LOOK FOR MECHANICAL OBSTRUCTION OR WIPER MOTOR FAULTY.

Nov 14, 2010 | Chevrolet S 10 Cars & Trucks

1 Answer

I cant figure out how to change my windshield wiper blades on 2001 ford ranger


How to Replace Wiper Blades Guide (Typical):
Potential tools needed to replace wiper blades:
  • Flat blade screwdriver (small)
  • Small nosed pliers
  • Latex or vinyl gloves
  • Safety goggles
To replace wiper blades theactual action of replacing the blade is no big deal, it's the locationof the blade down below the hood that can make it difficult though.Sometimes it helps to open the hood to gain access to the wiper blades.Other times it is helpful if the wiper blade is somewhere in the motionline of wiper action. The trick is to get the wiper to stop somewherein the wiper arc. Turn the wipers to the on position and allow thewipers to start, and then shut the key off when the wiper has arrivedin a desirable position on the windshield. To replace your wiper bladesplease follow the step by step instruction below. Also, watch the How to replace wiper blades video below to gain additional information. The method in which the wiper blades are attached will vary slightly.
  • Step 1: With the hood closed, turn the wiperson, when the wipers are in the middle of their arc turn the key to theoff position. (Note: if this can't be done because of wiper conditionand you want to avoid scratching the windshield please open your hoodto gain access)
  • Step 2: Locate the mounting clips at the top pivot on the wiper blade
  • Step 3: Release the clip and remove the wiper arm
  • Step 4: Match the size of the old blade against the new blade to ensure proper fit and operation
  • Step 5: Reinstall the new wiper blade and recheck wiper operation

Common Problems:
  • Make sure the wiper blades are the same size as the original blades.
  • When replacing wiper blades not getting the blade onthe mounting pin completely allowing the wiper arm to become dislodgedand possibly causing damage to the windshield.
  • Using wiper blades after the blade has failed permanently damaging the windshield by craving scratches in the wiper arc.
  • Wiper blade can create a chattering noise when theblade is not properly balanced allowing the blade to "flop" back andforth as the wiper direction changes.

I hope help you with this (remember rated this help) Good luck.

Sep 16, 2009 | 2001 Ford Ranger Regular Cab

2 Answers

How do I remove front wiper blades to replace with new ones on my 2006 nissan quest


How to Replace Wiper Blades Guide:
Potential tools needed to replace wiper blades:
  • Flat blade screwdriver (small)
  • Small nosed pliers
  • Latex or vinyl gloves
  • Safety goggles
To replace wiper blades the actual action of replacing the blade is no big deal, it's the location of the blade down below the hood that can make it difficult though. Sometimes it helps to open the hood to gain access to the wiper blades. Other times it is helpful if the wiper blade is somewhere in the motion line of wiper action. The trick is to get the wiper to stop somewhere in the wiper arc. Turn the wipers to the on position and allow the wipers to start, and then shut the key off when the wiper has arrived in a desirable position on the windshield. To replace your wiper blades please follow the step by step instruction below. Also, watch the How to replace wiper blades video below to gain additional information. The method in which the wiper blades are attached will vary slightly.
  • Step 1: With the hood closed, turn the wipers on, when the wipers are in the middle of their arc turn the key to the off position. (Note: if this can't be done because of wiper condition and you want to avoid scratching the windshield please open your hood to gain access)
  • Step 2: Locate the mounting clips at the top pivot on the wiper blade
  • Step 3: Release the clip and remove the wiper arm
  • Step 4: Match the size of the old blade against the new blade to ensure proper fit and operation
  • Step 5: Reinstall the new wiper blade and recheck wiper operation

Common Problems:
  • Make sure the wiper blades are the same size as the original blades.
  • When replacing wiper blades not getting the blade on the mounting pin completely allowing the wiper arm to become dislodged and possibly causing damage to the windshield.
  • Using wiper blades after the blade has failed permanently damaging the windshield by craving scratches in the wiper arc.
  • Wiper blade can create a chattering noise when the blade is not properly balanced allowing the blade to "flop" back and forth as the wiper direction changes.

I hope help you with this (remember rated this help) Good luck.

Sep 14, 2009 | 2006 Nissan Quest

1 Answer

Wiper does not stop wiping until engine shut-off


you need to replace multi function switch

May 08, 2009 | 2001 Oldsmobile Intrigue

Not finding what you are looking for?
1986 Mazda RX-7 Logo

189 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

77514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8826 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...