Question about 1984 Toyota Celica Supra

1 Answer

1984 toyota supra rear wheel bearing

I need to know how to change rear wheel bearing on the driverside of my toyota supra

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has achieved Level 3.

  • Master
  • 479 Answers

First remove hubcap (if any) then remove the wheel. remove the drum, and you will see the hub/bearing unit, it should be bought at a Toyota dealer as a whole kinda pricey, but always try to stay with OEM. look behind the hub and as you turn the hub(where the 4 lugs are) you will see 4 other 14mm bolts on the black backing plate. remove them and it should come out. if not, a little tap with a rubber mallet will do the trick. the 2 holes on top are spaced further than the 2 bottom holes, so careful while installing. hand tighten all bolts first then tighten to specs. good luck 

Posted on Dec 15, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I got a 1984 Toyota Celica supra that when I go to take of it has no power?

1984 ? trade it in on the goverment cash back schemes against a new car ,this is a old car and it could have a lot of problems and to diagnose it correctly i would need my head under the bonnet

Oct 08, 2013 | 1984 Toyota Celica Supra

1 Answer

1984 toyota surpa starts runs 10 sec. then dies

My first thought would be a bad sensor. Possibly crank shaft position sensor which provides spark to ignition. have you changed your fuel filter and cap and rotor on the distributor? Have you checked for any vacuum leaks? Is the check/service engine light on? You can test any sensor and RELAY with an ohmmeter in the ohm setting to see if there is continuity.
You can go to and register for full free online repair manual for your supra.

Dec 09, 2009 | 1984 Toyota Celica Supra

1 Answer

How to change a rear wheel bearing on a 1994 toyota camry

The rear wheel bearing on a toyota camry is replaced by replacing the wheel bearing and hub as a unit. this is a design change as compare to older models with two piece wheel bearings. Scotch drive wheels. Remove rear wheel. Remove rear brake drum. (note: if emergency brakes are applied you will not be able to remove brake drum) Remove dust cap and hub retaining nut. Hub should slide off as unit. Replace hub with new unit. Installation is reverse of removal.

May 30, 2009 | 1994 Toyota Camry

1 Answer

Engine will not start where is connection for finding diagnostic fault codes? are these flash codes when connected?

sounds like a fuel pressure problem. no flash codes for that year that will tell you anything. make sure the fuel pump is working.

May 24, 2009 | 1984 Toyota Celica Supra

2 Answers

My son has a 88 toyota supra with a tront end

camp5tn1: yes, the front wheel bearing is one large bearing which must be pressed out. "O"Reilley's and number of other automotive parts house will do this pretty cheap. It's not worth the hassle unless you have the proper tools. Just remove the whole steering knuckle with the bearing in it, minus the axle and carry it down to them.

Mar 14, 2009 | 1989 Toyota Supra

1 Answer

91 Toyota Supra rear vibration

I have a similar problem with my car and it is linked to the rear trailing arm bushes which cause the rear tyres to warp on the inner side of the tyre wall which makes this wuring noise at certain speeds so have them checked out!

Mar 12, 2009 | 1991 Toyota Supra

2 Answers

How to a Change the Driver Side Wheel Breaing? 93 Toyota Corolla

need to take wheel off and take the 3 or4 bolts out of bearing also may need to take axle nut off should come off with ahammer.

Jan 01, 2009 | 1993 Toyota Corolla

1 Answer

Rear wheel lock up/driver side/2wheel drive

spider gears in rearend r broken and binding up on the ring gear

Dec 19, 2008 | 2003 Chevrolet Silverado 1500

2 Answers

Rough Idle on 1984 Toyota Celica Supra

You said you replaced the plugs - did you use the toyota platinum plugs? I found out the hard way that even the platinum plugs from bosch or any other kind of platinum plug just doesn't work right. Yes, they are more expensive from toyota, but they can make a difference in the way the engine runs.

Jul 22, 2008 | 1984 Toyota Celica Supra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

83851 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22413 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides