Question about 1998 Subaru Forester

2 Answers

Removing Camshaft pulley on 2.5 Dohc forester motor

I am replacing the engine in 98 forester with the 2.5 Dohc engine. I need to remove the timing belt and remove the upper drivers side camshaft pulley in order to replace a damaged camshaft sensor bracket which was glued on by someone before I bought engine. I need to know where to position the crankshaft and cams so I can remove the belt without damagintg the valves. I was told at the subaru forester forum this is possible but have not been able to find the info I need. I cannot even find a repair manual for this car when calling auto supply store
Any help would be appreciated

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

To replace the timing belt back guard you will have to remove both pulleys.There is a small bolt under each pulley holding the belt guard Use a large socket to hold the pulley while you break the bolt loose with a 17mm socket. I have just done this while replacing my head gaskets due to coolant boiling from the gasket leak.

Posted on Jan 11, 2009

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 43 Answers

Go to kotuku29@gmail and comprehensive details will be passed on at your request.

Posted on Dec 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

REPLACE TIMMING BELT- 2000 TROOPER


3.2L & 3.5L (6VE1) Engines
  1. Disconnect the negative battery cable.
  2. Remove the air cleaner assembly and intake air duct.
  3. Remove the upper fan shroud from the radiator.
  4. Remove the 4 nuts retaining the cooling fan assembly. Remove the cooling fan from the fan pulley.
  5. Loosen and remove the drive belts.
  6. Remove the upper timing belt covers.
  7. Remove the fan pulley assembly.
  8. Rotate the crankshaft to align the camshaft timing marks with the pointer dots on the back covers. Verify that the pointer on the crankshaft aligns with the mark on the lower timing cover. NOTE When the timing marks are aligned, the No. 2 piston is at Top Dead Center (TDC) compression. WARNING Align the camshaft and crankshaft sprockets with their alignment marks before removing the timing belt. Failure to align the belt and sprocket marks may result in valve damage.
  9. Use tool No. J-8614-01, or a suitable pulley holding tool to remove the crankshaft pulley center bolt. Remove the crankshaft pulley.
  10. If present, disconnect the 2 oil cooler hose bracket bolts on the timing cover. Move the oil cooler hoses and bracket off of the lower timing cover.
  11. Remove the lower timing belt cover.
  12. Remove the pusher assembly (tensioner) from below the belt tensioner pulley. The pusher rod must always face upward to prevent oil leakage. Depress the pusher rod, and insert a wire pin into the hole to keep the pusher rod retracted.
  13. Remove the timing belt.
  14. Inspect the water pump and replace it if there is any doubt about its condition.
  15. Repair any oil or coolant leaks before installing a new timing belt. If the timing belt has been contaminated with oil or coolant, or is damaged, it must be replaced. 79245g08.gif Using a double clip to hold the belt in place-Isuzu 3.2L and 3.5L engines Click to Enlarge 79245g07.gif For maximum timing belt life, install the belt as shown-Isuzu 3.2L and 3.5L engines Click to Enlarge 93025g10.gif View of timing belt tensioner and pusher-Isuzu 3.2L and 3.5L engines Click to Enlarge 79245g06.gif Proper crankshaft alignment marks for timing belt installation-Isuzu 3.2L SOHC (VIN V) engine Click to Enlarge 93025g09.gif Timing mark alignment and timing belt routing-Isuzu 3.2L SOHC (VIN V) engine Click to Enlarge 93025g11.gif Timing mark alignment and timing belt routing-Isuzu 3.2L (VIN W) and 3.5L DOHC engines Click to Enlarge 79245g11.gif View of timing belt tensioner pusher-Isuzu 3.2L and 3.5L engines Click to Enlarge
To install:
  1. Verify that the sprocket timing marks are still aligned and that the groove and the keyway on the crankshaft timing sprocket align with the mark on the oil pump. The white pointers on the camshaft timing sprockets should align with the dots on the front plate.
  2. Install the timing belt. Use clips to secure the belt onto each sprocket until the installation is complete. Align the dotted marks on the timing belt with the timing mark opposite the groove on the crankshaft sprocket. NOTE The arrows on the timing belt must follow the belt's direction of rotation. The manufacturer's trademark on the belt's spine should be readable left-to-right when the belt is installed.
  3. Align the white line on the timing belt with the alignment mark on the right bank camshaft timing pulley. Secure the belt with a clip. WARNING If any binding is felt when adjusting the timing belt tension by turning the crankshaft, STOP turning the engine, because the pistons may be hitting the valves.
  4. Rotate the crankshaft counterclockwise to remove the slack between the crankshaft sprocket and the right camshaft timing belt sprocket.
  5. Install the belt around the water pump pulley.
  6. Install the belt on the idler pulley.
  7. Align the white alignment mark on the timing belt with the alignment mark on the left bank camshaft timing belt sprocket.
  8. Install the crankshaft pulley and tighten the center bolt by hand. Rotate the crankshaft pulley clockwise to give slack between the crankshaft timing belt pulley and the right bank camshaft timing belt pulley.
  9. Insert a 1.4mm piece of wire through the hole in the pusher to hold the rod in. Install the pusher assembly while pushing the tension pulley toward the belt.
  10. Pull the pin out from the pusher to release the rod.
  11. Remove the clamps from the sprockets. Rotate the crankshaft pulley clockwise 2 turns. Measure the rod protrusion to ensure it is between 0.16-0.24 in. (4-6mm).
  12. If the tensioner pulley bracket pivot bolt was removed, tighten it to 31 ft. lbs. (42 Nm).
  13. Tighten the pusher bolts to 14 ft. lbs. (19 Nm).
  14. Remove the crankshaft pulley. Install the lower and upper timing belt covers and tighten their bolts to 12 ft. lbs. (17 Nm).
  15. Fit the oil cooler hose onto the timing cover and tighten its mounting bracket bolts to 16 ft. lbs. (22 Nm).
  16. Install the crankshaft pulley and tighten the pulley bolt to 123 ft. lbs. (167 Nm).
  17. Install fan pulley assembly and tighten the bolts to 16 ft. lbs. (22 Nm).
  18. Install and adjust the accessory drive belts.
  19. Install the cooling fan assembly and tighten the bolts to 72 inch lbs. (8 Nm).
  20. Install the upper fan shroud.
  21. Install the air cleaner assembly and intake air duct.
  22. Connect the negative battery cable.

Jan 18, 2014 | Isuzu Trooper Cars & Trucks

1 Answer

Water pump 2000 3.0 liter dodge caravan


For The 3.0 Motor. (3.3 Way down the line.)

Drain cooling system.
Remove timing belt. Refer to Engine for procedure.
Remove water pump mounting bolts.
Separate pump from water inlet pipe and remove water pump.

Timing Belt Removal
Raise vehicle and remove accessory drive belt splash shield (Fig. 66).
Remove accessory drive belts.
Remove crankshaft pulley and damper (Fig. 68).
Support engine and remove right side engine mount.
Remove engine support bracket (Fig. 67).
Remove timing belt covers (Fig. 67).
Mark belt running direction for installation (Fig. 69).
Loosen timing belt tensioner bolt (Fig. 71) and remove timing belt.
Remove crankshaft sprocket flange shield (Fig. 68). CAMSHAFT SPROCKETS To remove camshaft sprockets
Hold camshaft sprocket with Spanner Tool MB-990775. Loosen and remove bolt and washer (Fig. 70).
Remove camshaft sprocket from camshaft. To install camshaft sprockets:
Place camshaft sprocket on camshaft.
Install bolt and washer to camshaft. Using Spanner Tool MB-990775, hold camshaft sprocket and torque bolt to 95 Nm (70 ft. lbs.) (Fig. 70). TIMING BELT TENSIONER
Install timing belt tensioner and tensioner spring.
Hook spring upper end to water pump pin and lower end to tensioner bracket with hook out (Fig. 71).
Turn timing belt tensioner counterclockwise full travel in adjustment slot and tighten bolt to temporarily hold this position (Fig. 72).

INSTALLATION


Install timing belt on crankshaft sprocket and keep belt tight on tension side (Fig. 69). Install belt on the front (radiator side) camshaft sprocket. Install belt on the water pump pulley, rear camshaft sprocket and finally on the timing belt tensioner.
Rotate the front camshaft sprocket in opposite direction to take up belt slack. Check that all timing marks are aligned (Fig. 69).
Install crankshaft sprocket flange (Fig. 68).
Loosen tensioner bolt and allow spring to tension timing belt.
Turn crankshaft two full turns in clockwise direction. Turn smoothly and in clockwise direction ONLY.
Align the timing marks on the sprockets and tighten the timing belt tensioner locking bolt to 28 Nm (250 in. lbs.) torque.
Install timing belt covers.
Install engine support bracket.
Install right side engine mount.
Install crankshaft damper and pulleys (Fig. 68). Tighten damper center bolt to 135 Nm (100 ft. lbs.) .
Install accessory drive belts.
Install accessory drive belt splash shield (Fig. 66).

Be sure to also replace all the cam and crank seals why you are there. Might as well put a belt on too.

FOR THE 3.3 OR 3.8 MOTORS.

Drain Cooling System.
Remove accessory drive belt.
Remove right front lower fender shield.
Remove water pump pulley bolts and remove pulley.
Remove water pump mounting screws. Remove water pump.
Remove and discard O-ring seal.
Clean O-ring groove and O-ring surfaces on pump and chain case cover. Take care not to scratch or gouge sealing surface

Installation

Install new O-ring into groove.
Install water pump to chain case cover. Tighten screws to 12 Nm (105 inch lbs.) .
Rotate pump by hand to check for freedom of movement.
Position pulley on pump. Install screws and tighten to 30 Nm (250 inch lbs.) .
Install accessory drive belt.
Install right front lower fender shield.
Refill Cooling System.

FOR THE 2.4 MOTOR

Disconnect negative cable from battery.
Raise vehicle on a hoist. Remove right inner splash shield.
Remove accessory drive belts.
Drain cooling system.
Support engine from the bottom and remove right engine mount.
Remove right engine mount bracket.
Remove timing belt. Refer to Engine for procedure.
Remove timing belt idler pulley.
Hold camshaft sprocket with Special tool C-4687 and adaptor C-4687-1 while removing bolt. Remove both cam sprockets.
Remove rear timing belt cover.

Install new O-ring gasket in water pump body O-ring groove. CAUTION: Make sure O-ring is properly seated in water pump groove before tightening screws. An improperly located O-ring may cause damage to the O-ring and cause a coolant leak.
Assemble pump body to block and tighten screws to 12 Nm (105 inch lbs.) . Pressurize cooling system to 15 psi with pressure tester and check water pump shaft seal and O-ring for leaks.
Rotate pump by hand to check for freedom of movement.
Install rear timing belt cover.
Install camshaft sprockets and torque bolts to 101 Nm (75 ft. lbs.) .
Install timing belt idler pulley and torque mounting bolt to 61 Nm (45 ft. lbs.) .
Install timing belt. Refer to Engine for procedure.
Install right engine mount bracket and engine mount. Refer to Engine for procedure.
Fill cooling system.
Install accessory drive belts.
Lower vehicle and connect battery cable.

Mar 29, 2012 | Cars & Trucks

1 Answer

1977 ford pinto timming marks


Hope this helps. Please don't forget to rate....thanks!



c17hydro_169.gif

Crankshaft, camshaft, and distributor timing marks-2300 cc engine (© Ford Motor Co.)


On 2000 cc engines, turn the crankshaft until the two round locating holes in the camshaft pulley are visible from the rear side of the pulley, looking forward from the left-side of the car. When these two holes are parallel to the ground, the timing pointer on the crankshaft pulley should point to TDC. If the drive belt is dislocated, the crankshaft damper will be retarded or advanced 19° per cog on the belt.

If the engine you are working on does not have the two locating holes on the rear side of the camshaft pulley, then you will have to remove the drive belt cover and observe that when the crankshaft timing marks are aligned to TDC of the compression stroke of the No. 1 cylinder, the distributor rotor is pointing to the index mark on the upper lip of the distributor housing which coincides with No. 1 spark plug tower, and the pointer on the camshaft pulley is aligned with the index mark on the cylinder head.

On 2300 cc engines, there is an access plug provided in the cam drive belt cover so that the camshaft timing can be checked without removing the drive belt cover. Remove the access plug, turn the crankshaft until the timing mark on the crankshaft damper indicates TDC, and observe that the timing mark on the camshaft drive sprocket is aligned with the pointer on the inner belt cover. Also, the rotor of the distributor must align with the No. 1 cylinder firing position.


CAUTION:

After any procedure requiring removal of the rocker arms on the 2300, each lash adjuster must be fully collapsed after assembly, then released. This must be done before the camshaft is turned.



Crankshaft, camshaft, and distributor timing marks-2300 cc engine (© Ford Motor Co.)

Crankshaft, camshaft, and distributor timing marks-2300 cc engine (© Ford Motor Co.)
c17hydro_170.gif

Checking 2000 cc overhead camshaft timing (© Ford Motor Co)

May 08, 2011 | Ford Mustang Cars & Trucks

1 Answer

Need to know timing marks


REMOVAL
1. Disconnect negative battery cable.
2. Loosen power steering lock bolts and nuts accordingly and remove tension from power steering (P/S) and/or air conditioning (A/C) compressor drive belt.
3. Remove P/S and/or A/C drive belt.
4. Loosen generator mounting bolts and adjusting bolt.
5. Remove generator bolts.
6. Remove water pump pulley.
7. Remove crankshaft pulley.
8. Remove upper and lower timing belt covers.
9. Turn crankshaft so that timing mark on timing belt pulley is aligned with timing mark on engine.
10. Check that "I" mark on intake camshaft pulley is aligned with mark on seal plate and "E" mark on exhaust camshaft pulley is aligned with mark on seal plate.
Do not move camshaft or crankshaft once timing marks have been correctly positioned.
11. Loosen tensioner pulley lock bolt.
12. Protect timing belt with a rag.
13. Remove tensioner pulley.
14. Remove timing belt. Mark the direction of timing belt rotation (on the timing belt) for proper reinstallation.

INSTALLATION
1. Install tensioner pulley. Replace tensioner spring whenever timing belt is replaced.
2. Pull tensioner pulley to its furthest point and tighten lock bolt.
3. Check that timing mark on timing belt pulley is aligned with timing mark on engine.
4. Check that "I" mark on intake camshaft pulley is aligned with mark on seal plate and "E" mark on exhaust camshaft pulley is aligned with mark on seal plate.
If existing timing belt is being reused, install belt in proper rotation direction marked prior to removal.
5. Install timing belt onto timing belt pulley first, then idler pulley, exhaust camshaft pulley, intake camshaft pulley, and tensioner pulley in that order.
6. Check that there is no looseness in belt between idler pulley and exhaust camshaft pulley or between intake and exhaust camshaft pulleys.
7. Loosen tensioner pulley lock bolt and allow tensioner spring to apply tension to timing belt.
Do not add additional tension.
8. Tighten tensioner pulley lock bolt to specified torque.
Tightening torque:28~38 lb-ft (38~51 N·m, 3.9~5.2 kg-m)
9. Rotate crankshaft two full revolutions (clockwise only) and align timing mark on timing belt pulley with timing mark on engine block.
10. Check that "I" mark on intake camshaft pulley and "E" mark on exhaust camshaft pulley are aligned with marks on seal plate.
11. If they are not aligned, remove timing belt and start process from tensioner installation.
12. Measure timing belt deflection by applying moderate pressure midway between camshaft pulleys. If deflection is not correct, repeat from tensioner installation.
Deflection pressure:22 Ib. (98 N, 10 kg)Deflection:0.39~0.50 in. (11~13 mm)
13. Install lower and upper timing belt covers in that order.
Tightening torque:5.8~8.0 Ib-ft (7.9~10.7 N·m, 0.8~1.1 kg-m)
14. Install timing belt guide plate and crankshaft pulley.
Tightening torque:9.0~12.6 lb-ft (12.3~17.2 N·m, 1.3~1.8 kg-m)
15. Install water pump pulley.
Tightening torque:9.0~12.6 lb-ft (12.3~17.2 N·m, 1.3~1.8 kg-m)
16. Install generator belt and adjust the tension.
17. Install P/S and/or A/C drive belt and adjust the tension.
18. Connect negative battery cable.

INSPECTION
Never forcefully twist, turn inside out or bend timing belt. Do not allow oil or grease to come in contact with timing belt.
1. Replace timing belt if it is contaminated with oil or grease.
2. Check timing belt for uneven wear, fraying, peeling, cracking and hardening. Replace timing belt as necessary.
3. Bend timing belt into a "U" shape as shown in figure. Distance "A" must be at least 1.0 in (25 mm).
4. Inspect both idler pulley and tensioner pulley for uneven wear and smooth bearing operation.
5. Inspect camshaft pulleys and timing belt pulley for broken teeth or damage.
Replace any component that shows damage, excessive wear, or that appears prone to a possible failure.

Feb 26, 2011 | 2002 Kia Spectra

1 Answer

How to replace the timing chain of nissan cefiro v6 2000? its 97 model.


Engine - Timing Chain/Front Cover Revised Procedure
Classification:
EM98-009
Reference:
NTB98-107
Date:
January 15, 1999
GA16DE TIMING CHAIN/FRONT COVER
REVISED SERVICE PROCEDURE
APPLIED ENGINE:
GA16DE
APPLIED MODELS:
1991-94 Sentra (B13) w/GA16DE
1991-93 NX1600 (B13)
1995-99 Sentra (B14) w/GA16DE
1995-98 200SX (B14) w/GA16DE
SERVICE INFORMATION
A revised service procedure for the engine front cover/timing chain has been adopted for the GA16DE. It is no longer recommended to remove the
cylinder head when removing the timing chain/front cover(s). Utilize the following steps when servicing the front cover, timing chain, guides or
tensioner(s)
PARTS INFORMATION
CLAIMS INFORMATION
Please reference the "Revision C" pages of the Nissan "1992-1999 Warranty Flat Rate Information Manual", Section "AG", Op Codes AG12AA,
AG14AA, AG142A, AG143A, AG144A and AG24AA. Also reference Section "CA", Op Codes CA20AA and CA22AA. You will note that the
descriptions and flat rate times applicable to the B13 and B14 vehicles (with GA16DE engines) for these Op Codes have been revised to reflect this
new procedure.
Caution
^ After removing the timing chain, do not turn the crankshaft and camshaft separately or the valves will strike the piston heads.
^ When installing chain tensioners or other sliding parts, lubricate contacting surfaces with new engine oil.
^ Apply new engine oil to bolt threads and seat surfaces when installing the camshaft sprockets and the crankshaft pulley.
^ Do not spill engine coolant on the drive belts.
^ Please refer to the Service Manual for the correct tightening torque.
Removal
1. Set # 1 piston at TDC on its compression stroke.
2. Remove the spark plug wires.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 2
3. Remove the rocker cover (see Figure 1).
4. Remove the coolant reservoir tank with bracket and reposition it for clearance.
5. Support the engine with a suitable jack.
6. Remove cylinder head front mounting bracket.
7. Remove engine front mounting, then the engine front mounting bracket.
8. Remove cylinder head front cover.
9. Remove the upper chain tensioner (see Figure 2).
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 3
10. Wipe off the links of the upper timing chain next to the timing marks on the sprockets. Put paint marks on the timing chain, matching them with
the timing marks on the cam sprockets and idler sprocket (see Figure 3)
11. Remove the four (4) front cover to cylinder head bolts.
12. Remove side and lower engine compartment splash covers.
13. Remove the accessory drive belts.
14. Remove the crankshaft pulley.
15. Drain coolant by removing the cylinder block drain plug and opening the radiator drain **** (Refer to MA section of the Service Manual).
16. Drain engine oil.
17. Remove intake manifold support of engine front side.
18. Remove power steering pump, pump bracket and tension rod. Position pump aside for clearance.
19. Remove the thermostat housing (See Figure 4).
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 4
20. Remove the lower chain tensioner (see Figure 5).
21. Remove the front exhaust tube. Refer to the "FE" section (Exhaust System) of the Service Manual.
22. Remove the front and rear engine gussets (if equipped) on either side of the oil pan.
NOTE:
On A/T models, remove the rear plate cover.
23. Remove the oil pan (see Figure 6).
a. Insert the Tool between the cylinder block and oil pan.
CAUTION:
Be careful not to damage the aluminum mating face. Do not insert a screwdriver, or the oil pan flange will become damaged.
b. Slide the Tool by tapping it on the side of the Tool with a hammer.
24. Remove the A/C compressor and position it aside for clearance.
25. Remove the A/C and alternator bracket with the alternator.
26. Remove the oil pump drive spacer.
CAUTION:
Be careful not to scratch the drive spacer when removing it.
27. Remove the front cover bolts and front cover.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 5
CAUTION:
One bolt is located on the water pump (see Figure 7).
*1: Located on engine front mounting bracket.
*2: Located on the water pump.
*3: Located on the power steering oil pump adjusting bar.
CAUTION:
Be careful not to tear or damage the cylinder head gasket.
28. Remove the cylinder block to front cover alignment dowels.
CAUTION:
Do not hit the dowels or the cylinder block will crack.
29. Wipe off the links of the lower timing chain next to the timing marks on the sprockets. Put paint marks on the timing chain, matching them with
the timing marks on the idler sprocket and crankshaft sprocket (see Figure 8).
Installation
1. Install the crankshaft sprocket, making sure the mating marks face the front of the engine.
2. Install the idler sprocket and lower timing chain using the mating marks and the paint marks made during the removal process.
CAUTION:
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 6
Be careful not to tear or damage the cylinder head gasket.
3. Install the lower chain guides.
4. Front cover installation:
a. Using a scraper or other suitable tool remove all traces of liquid gasket from the cylinder block and front cover mating surfaces.
b. Install new crankshaft seal in front cover.
c. Install new oil passage O-rings and apply a continuous bead of RTV sealant to the front cover (see Figure 1).
NOTE:
Use Genuine Nissan RTV silicone sealant P/N 999MP-A7007, Three Bond P/N TB1207D or equivalent.
d. Install the front cover to the engine.
CAUTION:
Be careful not to tear or damage the cylinder head gasket or oil seal.
5. Align oil pump drive spacer with the oil pump, and install.
6. Install the oil strainer.
7. Install oil pan, referring to "Installation" in the "OIL PAN" section of the Service Manual.
8. Install upper timing chain and sprockets, using the painted reference marks made during removal.
9. Install upper chain tensioner.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 7
a. Before installing the chain tensioner, insert a suitable pin into the pin hole of the chain tensioner (see Figure 2) to hold the tensioner in.
b. Once the tensioner is installed, remove the pin.
10. Install the lower chain tensioner (See Figure 3).
NOTE:
Make sure the gasket is facing the proper direction before installing the tensioner.
CAUTION:
Now rotate the crankshaft by hand. Check that no binding or interference problems occur when the engine is rotated.
11. Install the thermostat housing.
a. Use a scraper to remove all traces of liquid gasket from the mating surfaces of the engine front cover and the thermostat housing.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 8
b. Apply a continuous bead of RTV sealant to the housing as shown in Figure 4.
NOTE:
Use Genuine Nissan RTV silicone sealant P/N 999MP-A7007, Three Bond P/N TB1207D or equivalent.
12. Install camshaft sprocket cover:
a. Use a scraper to remove all traces of liquid gasket from the mating surfaces of the cylinder head and camshaft sprocket cover.
b. Apply a continuous bead of RTV sealant to the cover as shown in Figure 5.
NOTE:
Use Genuine Nissan RTV silicone sealant P/N 999MP-A7007, Three Bond P/N TB1207D or equivalent.
d. Install camshaft sprocket cover.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 9
13. Apply RTV sealant to rocker cover gasket (see Figure 6a) and install rocker cover, tightening the bolts as shown in Figure 6b.
14. Install the following parts:
a. Crankshaft pulley.
b. A/C compressor and alternator bracket with alternator.
c. A/C compressor.
d. Power steering oil pump and tension rod.
15. Install front and rear engine gussets (if equipped), and rear cover plate (A/T models).
16. Install front exhaust tube.
17. Install upper right engine bracket and mount.
18. Install coolant reservoir tank.
19. Install alternator, power steering and A/C compressor drive belts.
20. Install engine compartment splash guards.
21. Install vacuum hoses, electrical harnesses and connectors.
22. Install spark plug wires.
23. Refill with coolant. Refer to the "MA" section ("Changing engine coolant, Engine Maintenance") of the Service Manual.
24. Refill with engine oil. Refer to the "MA" section ("Changing engine oil, Engine Maintenance") of the Service Manual.

Jan 15, 2011 | 1997 Nissan 200SX

3 Answers

Timing belt diagram for a 1999 ford escort 2.0


Hope this helps you, you also might want to replace the water pump, due to it's timing belt driven.

29c5183.gif

Sep 24, 2010 | Ford Escort Cars & Trucks

1 Answer

How to change a timming belt on honda civic


Timing Belt and Tensioner REMOVAL & INSTALLATION 1984–87 Engines
  1. Turn the crankshaft pulley until it is at Top Dead Center.
  2. Remove the pulley belt, water pump pulley, crankshaft pulley, and timing gear cover. Mark the direction of timing belt rotation.
  3. Loosen, but do not remove, the tensioner adjusting bolt and pivot bolt.
  4. Slide the timing belt off of the camshaft timing gear and the crankshaft pulley gear and remove it from the engine.
  5. To remove the camshaft timing gear pulley, first remove the center bolt and then remove the pulley with a pulley remover or a brass hammer. This can be accomplished by simply removing the timing belt upper cover, loosening the tensioner bolts, and sliding the timing belt off of the gear to expose the gear for removal. NOTE: If you remove the timing gear with the timing belt cover in place, be sure not to let the woodruff key fall inside the timing cover when removing the gear from the camshaft. Inspect the timing belt. Replace if over 90,000 miles old, if oil soaked (find source of oil leak also), or if worn on leading edges of belt teeth. Fig. 1: Timing belt and front cover assembly — 1984–87 engines 86833161.gif
    Fig. 2: Positioning the crankshaft and camshaft pulleys before installing the timing belt — 1984–87 engines 86833162.gif
    Fig. 3: Timing belt tension adjustment — 1984–87 engines 86833163.gif
    To install:
  6. Be sure to install the crankshaft pulley and the camshaft timing gear pulley in the top dead center position. Align the marks on the camshaft timing gear so they are parallel with the top of the cylinder head and the woodruff key is facing up. NOTE: When installing the timing belt, do not allow oil to come in contact with the belt. Oil will cause the rubber to swell. Be careful not to twist the belt unnecessarily or bend in a 90°angle, since it is made with fiberglass; nor should you use tools having sharp edges when installing or removing the belt. Be sure to install the belt with the arrow facing in the same direction it was facing during removal.
  7. After installing the belt, adjust the belt tension by first rotating the crankshaft counterclockwise 1/4 turn. Then, re-tighten the adjusting bolt and finally the tensioner pivot bolt.
  8. Replace the other components removed for belt access.
  9. Start the car, check timing and adjust if necessary WARNING
    Do not remove the adjusting or pivot bolts, only loosen them. When adjusting, do not use any force other than the adjuster spring. If the belt is too tight, it will result in a shortened belt life.

Aug 31, 2010 | 1986 Honda Civic

1 Answer

Timing belt broke,engine out of time,need to timing and install new belt how do i set timing.98 escort zx2 2.0 L


2.0L Engine SOHC ENGINE
  1. Remove the drive belt and timing cover.
  2. Raise the car and support it with safety stands.
  3. Remove the right-hand splash shield and the crankshaft pulley. Fig. 11: The timing marks on both the camshaft and crankshaft pulleys must be aligned like this before removing or installing the timing belt — 2.0L SOHC engines 90983g66.gif

  4. Align the timing marks as illustrated in the accompanying illustration.
  5. Refer to the accompanying illustration and remove the timing belt as follows:
    1. Loosen the timing belt tensioner bolt (1).
    2. Use an 8mm Allen wrench, and turn the tensioner (2) counterclockwise 1⁄4 turn.
    3. Insert a 1⁄8 inch drill bit in the hole (3) to lock the belt tensioner in place.
    4. Remove the timing belt (4). Fig. 12: Remove the timing belt by following these 4 numbered steps (refer to the text for an explanation) — 2.0L SOHC engine 90983g67.gif

    5. Inspect the belt for damage and signs of oil leakage. To install: NOTE: Install the timing belt over the sprocket in a counterclockwise direction starting at the crankshaft. Keep the belt span between the crankshaft and camshaft tight when installing the belt over the camshaft.
  6. Install the timing belt and remove the drill bit.
  7. Tighten the tensioner bolt to 15–22 ft. lbs. (20–30 Nm).
  8. Rotate the engine two complete revolutions and make sure the timing marks are aligned.
  9. Install the timing belt cover and crankshaft pulley.
  10. Install the right-hand splash shield and the drive belt.
  11. Start the car and check for proper operation.
DOHC ENGINE NOTE: A camshaft alignment timing tool (No. T94P-6256-CH or equivalent) and a crankshaft Top Dead Center (TDC) timing peg tool (No. T97P-6000-A or equivalent) are required for this procedure. NOTE: Make sure the correct notch in the pulley is indexed to the lower cylinder block. Refer to the accompanying illustration. Fig. 13: A camshaft alignment timing tool . . . 90983g68.gif
Fig. 14: . . . and a crankshaft TDC timing peg tool are required when removing and installing the timing belt 90983g69.gif
  1. Remove the spark plugs.
  2. Rotate the crankshaft to TDC.
  3. Locate and remove the plug bolt by the Crankshaft Position (CKP) sensor (refer to the illustration) and install the TDC timing peg. Fig. 15: Remove the plug bolt by the Crankshaft Position (CKP) sensor and install the TDC timing peg 90983g70.gif

  4. Raise the car and support it with safety stands.
  5. Unfasten the splash shields bolts and remove the shield.
  6. Lower the car and remove the water pump pulley.
  7. Remove the valve cover and the timing belt covers.
  8. Align the camshafts and install the camshaft alignment tool on the back of the camshafts as illustrated. Fig. 16: Align the camshafts and install the alignment tool 90983g76.gif
    WARNING
    If the camshaft belt is being reused, mark the direction of the camshaft belt to the rotation of the camshaft prior to removal, or premature wear and belt failure could occur.
  9. Loosen the tensioner pulley bolt and relieve the tension on the belt by disconnecting the tensioner tab from the timing cover back plate.
  10. Slide the belt off the sprockets.
  11. Inspect the belt for wear and replace as necessary. Fig. 17: Timing belt routing — 2.0L DOHC engine 90983g71.gif
    To install:
  12. If, for any reason, the engine was disturbed, the camshafts moved or the sprockets replaced, perform the following procedure: NOTE: Make sure the correct notch in the pulley is indexed to the lower cylinder block.
    1. Position the crankshaft just prior to Top Dead Center (TDC).
    2. If not already done, locate and remove the plug bolt by the Crankshaft Position (CKP) sensor (refer to the illustration) and install the TDC timing peg.
    3. Rotate the crankshaft clockwise against the TDC peg. NOTE: Installation of the alignment tool into the exhaust camshaft may require the camshafts to be rotated clockwise.
    4. Install the camshaft alignment tool on the back of the camshafts.
    5. Install the timing belt and engage the timing belt tensioner tab into the upper timing cover backplate. NOTE: A 3⁄8 inch drive, 10mm, 2 inch torque adapter offset is required to tighten the tensioner bolt.
    6. Using a 6mm Allen wrench, adjust the tensioner until the index marks are aligned and tighten the bolt to 17–20 ft. lbs. (22–28 Nm).
    7. Rotate the crankshaft clockwise against the TDC alignment peg, then remove the camshaft alignment tool.
    8. Remove the TDC peg tool and install the plug bolt.
    9. Install the timing and valve covers.
    10. Install the water pump pulley and the splash shield.
    11. Install the spark plugs. If the engine or the camshaft were not disturbed in any way, or the sprockets were not removed, perform the following procedure:
  13. Install the timing belt and engage the timing belt tensioner tab into the upper timing cover backplate. Fig. 18: Engage the timing belt tensioner tab into the upper timing cover backplate . . . 90983g72.gif
    Fig. 19: . . . then use a 6mm Allen wrench to adjust the tensioner until the index marks are aligned 90983g73.gif
    Fig. 20: A 3⁄8 inch drive, 10mm, 2 inch torque adapter offset is required to tighten the tensioner bolt (arrow) — 2.0L DOHC engine 90983g75.gif
    NOTE: A 3⁄8 inch drive, 10mm, 2 inch torque adapter offset is required to tighten the tensioner bolt.
  14. Using a 6mm Allen wrench, adjust the tensioner until the index marks are aligned and tighten the bolt to 17–20 ft. lbs. (22–28 Nm).
  15. Rotate the crankshaft clockwise against the TDC alignment peg, then remove the camshaft alignment tool. Fig. 21: Rotate the crankshaft clockwise against the TDC alignment peg 90983g74.gif

  16. Remove the TDC peg tool and install the plug bolt.
  17. Install the timing and valve covers.
  18. Install the water pump pulley and the splash shield.
  19. Install the spark plugs.
prev.gif next.gif

Aug 26, 2010 | Ford E-Series Cars & Trucks

2 Answers

The Timing belt


Recommended by kia is 100,000 km.

Timing Belt: Service and Repair
TIMING BELT
COMPONENT
REMOVAL
1. Disconnect negative battery cable.
2. Loosen power steering lock bolts and nuts accordingly and remove tension from Power Steering (P/S) and/or Air Conditioning (A/C) compressor
drive belt.
3. Remove P/S and/or A/C drive belt.
4. Loosen generator mounting bolts and adjusting bolt.
5. Remove generator bolts.
6. Remove water pump pulley.
7. Remove crankshaft pulley and timing belt guide plate.
8. Remove upper and lower timing belt covers.
9. Turn crankshaft so that timing mark on timing belt pulley is aligned with timing mark on engine.
10. Check that "I" mark on intake camshaft pulley is aligned with mark on cylinder head cover and "E" mark on exhaust camshaft pulley is aligned
with mark on cylinder head cover.
NOTE: Do not move camshaft or crankshaft once timing marks have been correctly positioned.
11. Loosen tensioner pulley lock bolt.
12. Protect timing belt with a rag.
13. Remove tensioner pulley.
14. Remove timing belt.
NOTE: Mark the direction of timing belt rotation (on the timing belt) for proper reinstallation.
INSPECTION
NOTE: Never forcefully twist, turn inside out or bend timing belt. Do not allow oil or grease to come in contact with timing belt.
1. Replace timing belt if it is contaminated with oil or grease.
2. Check timing belt for uneven wear, fraying, peeling, cracking and hardening. Replace timing belt as necessary.
3. Bend timing belt into a "U" shape as shown in figure. Distance "A" must be at least 1.0 inch (25 mm).
4. Inspect both idler pulley and tensioner pulley for uneven wear and smooth bearing operation.
5. Inspect camshaft pulleys and timing belt pulley for broken teeth or damage.
NOTE: Replace any component that shows damage, excessive wear, or that appears prone to a possible failure.
INSTALLATION
1. Install tensioner pulley.
NOTE: Replace tensioner spring whenever timing belt is replaced.
2. Pull tensioner pulley to its furthest point and tighten lock bolt.
3. Check that timing mark on timing belt pulley is aligned with timing mark on engine.
4. Check that "I" mark on intake camshaft pulley is aligned with mark on cylinder head cover and "E" mark on exhaust camshaft pulley is aligned
with mark on cylinder head cover.
NOTE: If existing timing belt is being reused, install belt in proper rotation direction marked prior to removal.
5. Install timing belt onto timing belt pulley first, then idler pulley, exhaust camshaft pulley, intake camshaft pulley, and tensioner pulley in that
order.
6. Check that there is no looseness in belt between idler pulley and exhaust camshaft pulley or between intake and exhaust camshaft pulleys.
7. Loosen tensioner pulley lock bolt and allow tensioner spring to apply tension to timing belt.
NOTE: Do not add additional tension.

8. Tighten tensioner pulley lock bolt to specified torque.
Tightening torque: 28 - 38 ft. lbs. (38 - 51 Nm, 3.9 - 5.2 kg-m)
9. Rotate crankshaft two full revolutions (clockwise only) and align timing mark on timing belt pulley with timing mark on engine block.
10. Check that "I" mark on intake camshaft pulley and "E" mark on exhaust camshaft pulley are aligned with marks on cylinder head cover.
11. If they are not aligned, remove timing belt and start process from tensioner installation.
12. Measure timing belt deflection by applying moderate pressure midway between camshaft pulleys. If deflection is not correct, repeat from
tensioner installation.
Deflection pressure: 22 lb. (98 N, 10 kg)
Deflection: 0.39 - 0.50 inch (11 - 13 mm)
13. Install lower and upper timing belt covers in that order.
Tightening torque: 5.8 - 8.0 ft. lbs. (7.9 - 10.7 Nm, 0.8 - 1.1 kg-m)
14. Install timing belt guide plate and crankshaft pulley.
Tightening torque: 9.0 - 12.6 ft. lbs. (12.3 - 17.2 Nm, 1.3 - 1.8 kg-m)
15. Install water pump pulley.
Tightening torque: 9.0 - 12.6 ft. lbs. (12.3 - 17.2 Nm, 1.3 - 1.8 kg-m)
16. install generator belt and adjust the tension.
17. Install P/S and/or A/C drive belt and adjust the tension.
18. Connect negative battery cable.

Sep 17, 2009 | 2003 Kia Rio

2 Answers

2000 isuzu trooper 3.2 v-6 dohc camshaft timing marks pulled camshafts to do valve job and need to align marks on drive gear and cams


It's more to it than aligning the marks since the cam pulleys turn about three times or more to one turn of the camshaft on this engine. You need to find someone that is experienced on this vehicle.

May 12, 2009 | 2000 Isuzu Trooper

Not finding what you are looking for?
1998 Subaru Forester Logo

896 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...