Question about 2004 Mazda 6

2 Answers

Air conditioning controls

The air conditioning blower fan only works on speeds 3 and 4, but the compressor cuts off. the compressor works on 1 and 2, but the blower will not come on. any ideas ?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Hey I have the same problem can you confirm it was the bloe motor resistor or the fan control relay? Cheers

Posted on Jan 13, 2015

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 163 Answers

Sounds like a bad switch.

Posted on May 08, 2009

6 Suggested Answers

leetamara
  • 702 Answers

SOURCE: Fan speed switch only works on #5

Call your local GMC Dealer and see if they have the climate control panel in stock. What happens is the circuit board on the back of the panel shorts out. The panel comes as an assembly and is very easy to replace. Don't go with a wrecking yard piece. I made that mistake once and it didn't work either. I got one from the Chevy dealer and it worked perfectly.

Posted on Aug 21, 2008

  • 221 Answers

SOURCE: 2004 Ford F150 - AC/Heater blower speed 1 & 2 not working.

You might have a bad speed selector switch, or your blower motor resistor is faulty.

Posted on Mar 17, 2009

  • 31 Answers

SOURCE: air condition fan only works on high speed, no low speed

You have a bad blower motor resistor. This is located under the dash close to the blower motor itself

Posted on Apr 14, 2009

inhisname
  • 76 Answers

SOURCE: Heat/AC Blower fan speed only works on High

hello, this sounds like a bad blower motor resistor!! its cheap and easy to change..if you need more info on locations let me know,, good luck.....marty

Posted on May 27, 2009

  • 3 Answers

SOURCE: Hummer H3 air condition blower will not come on -

http://www.trademotion.com/partlocator/index.cfm?action=getJointLocator&siteid=213932&chapter=&Sectionids=0,51825&groupid=51834&subgroupid=2385&componentid=0&make=1000&model=Hummer H3&year=2006&graphicID=GS06068&callout=4&catalogid=2&displayCatalogid=0


Forgot the link!

Posted on Aug 03, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why would my air conditioning in my Mitsubishi eclipse cool on #1 setting but kick off on any other setting above #1?


When you say "kick off," do you mean that the fan shuts off, or that the compressor cuts off? (Unclear.)
If the fan is shutting off, check your fan control switch, blower resistor, and blower motor.
If the compressor is cutting off, check your refrigerant level, and the compressor cycling switch.

Jul 25, 2014 | Cars & Trucks

1 Answer

Air conditioning not blowing cold after I changed blower resister


if the fan is running inside and the environmental controll is set to cool the AC compressor under the hood a click is heard and the compressor should start, it should cylcle on and off periodicly , if this dos not happen Have your AC system checked.

Jun 10, 2012 | 2002 Isuzu Rodeo

2 Answers

04 Saturn vue compressor turns off when fan is set to 3 or 4


The problem is the blower motor speed control resistor, it is located near the blower motor in the housing. I exchanged mine and it works like a charm now.

May 31, 2012 | 2002 Saturn VUE

1 Answer

How to cut power to air condition blower


well you can disconnect the power lead to the compressor to disable the A/C but the fan still blowing isnt the A/C. its the fan speed switch

Mar 13, 2012 | 1998 Mazda B-Series

1 Answer

The blower motor for the air conditioning doesn't come on. The compressor comes on. I ohmed the blower motor and it was good. I jumped the blower motor and it turned freely. With the control set 1 2 3...


> With the control set 1 2 3 4 it does blow any air,
? does NOT?
A common problem with this control is the failure of a stepped resistor which causes only the highest speed to still function since this bypasses the resistor.
Tracing the leads from the fan speed switch may help locate it.

Sep 04, 2011 | 1997 Honda Accord

2 Answers

The AC on my 2002 chevy S 10 just suddenly stopped blowing cold air. The freon is full and the compressor is coming on. Any advice would be helpful in this Texas heat. Thanks


If the freon is full and the compressor clutch is working,is the blower working, need more details, if it is, you could have a blocked orifice filter. or a bad high pressure switch located at the rear of the compressor.if the high pressure switch loses voltage or goes out, your cool air will come to a dead halt. check the high pressure switch for voltage. good luck!

Aug 08, 2011 | 2002 Chevrolet TrailBlazer

1 Answer

Ac controls quit working blower fan is running on high all thetime. compressor is not working.


fan elays are under hood in black box by battery. 3 of them. 2 for high speed, 1 for low speed. Default is high speed when there is a probem.

Suspect maybe they shorted something out when fixing dent. Did they do any welding on the van? Connecting the cables to the body can sometimes send voltage where it's not wanted.

Nov 06, 2008 | 2000 Nissan Quest

2 Answers

Air conditioning Fan


Actually the relay is not the problem here. Your blower resistor has gone bad. The resistor reduces the amount of power going to the fan, thus allowing the slower speeds. I don't know the exact location, though it is typically in the blower housing.

Oct 09, 2008 | 2000 Nissan Frontier

1 Answer

AIR CONDITIONING


heater controls could be gone

Jun 26, 2008 | 1999 Volkswagen Jetta

Not finding what you are looking for?
2004 Mazda 6 Logo

Related Topics:

266 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

64286 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...