Question about Ford Explorer

1 Answer

Wash fluid pump not working do you know fusebox position

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 651 Answers

Usually under dash by brake peddle, or in glove compartment on left.

Posted on Dec 15, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

In my 2007 Saturn Vue there is what I think is an air pump which is cracked that one port is not connected to anything.


There is a electric motor that pumps washer fluid . Located in the bottom of the washer fluid tank .
Wash Operation (Front and Rear Wipers)
The front and rear washer systems use the same windshield washer fluid pump. When either the front or rear wiper is in the washer position voltage will be supplied to one side of the windshield washer fluid pump (depending on whether it is front or rear), while the other side of the pump is grounded.
At this point, the windshield washer fluid pump sprays solvent onto the windshield. When the front or rear washer is activated, the BCM receives an input from the switch that is activated. The BCM will control the wipers while in the WASH mode. The BCM will control either the front wiper relay or the rear wiper relay to turn on the wipers. The windshield wipers operate at low speed for 3 swipes and returns to the park position.

When turning on the washers do you hear the motor run ? Have some one try it while you listen at the washer fluid tank ! These pump motors do go bad .
turn OFF the ignition.
Disconnect the harness electrical connector of the windshield washer fluid pump.
Connect a test lamp from the windshield washer pump control circuit to a good ground .
Turn ON the ignition, with the engine OFF.
Press the front washer switch.
Does the test lamp illuminate?
YES or NO !

Nov 18, 2016 | Saturn Cars & Trucks

2 Answers

2006 Hyundai Sonata. Windshield washer not working. Thought fluid was low. Can see fluid in fill tube. 105000 miles. Just bought it. Is this a difficult and costly repair?


Possibly the washer pump isn't working or the switch for it isn't working. It should be possible to unplug and straight wire the pump just to test it to see if it will operate is it gets power. A test light a the washer pump will tell you if it is getting power when the washer button is pressed.

Mar 08, 2015 | Hyundai Cars & Trucks

1 Answer

I need a diagram for a 2001 VW Cabrio relay. I thought number 6 was for the blinkers/hazards but it's not and its empty. 413 is in there and blinkers and hazards just stopped one day. I don't know if I...


A2Resource
a great vw resource site
25345733-zc0klvszlbpkidh1d23fhked-5-0_0.gif
Relays:
Num.Relay Arrangement and Pinout (with control number stamped on relay)
1A/C Relay (13 or 140)
1A/C Switch
2Radiator Cooling Fan
3Fan Switch High Speed
4Battery, Fuse 23
5A/C Clutch (via pressure and temperature switches)
6Main Fusebox Battery Power, Fuse 19
7Main Fusebox Ground
8Fresh Air Fan
2Rear Wiper Relay (72)
1Main Fusebox Ground
2Main Fusebox Run Power, Fuse 4
3Rear Wiper Motor
4Wipe/Wash Signal from Switch
3Digifant Control Unit (30 or 32), Motronic OBD1 Control Unit (109)
1Main Fusebox Ground
2Tachometer
3Main Fusebox Start/Run Power
4Main Fusebox Battery Power
5To ECU (relay ) (1990 G60, ABA/VR6 OBD1 only)
6To ECU and Engine Electronics
4Load Reduction Relay (18)
1From Ignition Switch Run Power
2To Main Fuse Box Run Power
3Main Fusebox Battery Power
4Main Fusebox Ground
5Low Coolant Level Control Unit (43)
1Main Fusebox Start/Run Power
2Low Coolant Level Sensor
3Coolant Temperature Sensor, Gauge
4Main Fusebox Ground
6Flashers (21)
1Main Fusebox Ground
2Flasher Output
3Flasher Input/Power
4X/6 (Trailer Light)
7Headlight Washer (33)
1Main Fusebox Ground (B/4 to C/3 to Ground)
2Headlight Washer Pump
3Headlight Switch Pin 56 (headlights) (B3 to D4 to light power)
4Main Fusebox Battery Power (B/5 to Y/2)
5Windshield Washer Pump (B/1 to B/2 to washer pump power)
8Wash/Wipe/Intermittent Relay (19 for standard relay, 99 for variable intermittent module)
1Main Fusebox Ground
2Intermittent Switch
3Main Fusebox Run Power, Fuse 5
4Park/Low Signal (ground when parked, positive when on low speed)
5Wiper Motor Low Speed Output
6Wash Switch (positive for front wash)
9Seat Belt Warning Control Unit (4 or 29)
1Main Fusebox Ground
2Seat Belt Switch
3Door Switch
4Seatbelt Light
5"Key In" Power from Ignition Switch
6Main Fusebox Start/Run Power
7Automatic Shoulder Belt Controller
9Radio/Lights Buzzer (36)
1Main Fusebox Ground (not used)
2A1/4 (Left Parking Lights)
3Vehicle Speed Sensor
4Seatbelt Light (not used)
5"Key In" Power from Ignition Switch
6Main Fusebox Start/Run Power (not used)
7A2/2 (Right Parking Lights)
10Fog Light Relay (110 for fog lights with low beam headlights only, 53 for parking light/high beam fog lights)
1Parking Light Power
2Headlight Switch Headlight Power (Low/High)
3Fog Light Switch Power, Fuse 10
4Main Fusebox Battery Power
5Main Fusebox Ground
6Low Beam Headlight Power
11Horn (53)
1Main Fusebox Start/Run Power
2To Horns
3Main Fusebox Ground
4From Horn Button
12Fuel Pump Relay (80, 67 or 167)
1Main Fusebox Starter Power (not used)
2Main Fusebox Start/Run Power
3To ECU (Fuel Pump )
4To Fuse 18, Fuel Pump, Oxygen Sensor Heater
5G2/6 (not used)
6Main Fusebox Battery Power From 30B
7G2/7, T1 (not used)
8Main Fusebox Ground (not used)
9M/4, U1/8, G2/5 (not used)
12Glow Plug Relay (102 or 104)
1Main Fusebox Starter Power
2Main Fusebox Start/Run Power
3Engine Temp Sender (preheat)
4Glow Plugs (Z1)To Fuse 18 (not used)
5G2/6 (not used)
6Main Fusebox Battery Power From 30B
7G2/7, T1 (not used)
8Main Fusebox Ground
9Water Separator, Glow Plug Light

remember to check out the website below for more help
http://www.xjamiex.com/mk2resource/electrical/CE2.html

Dec 30, 2014 | Cars & Trucks

1 Answer

Windshield washer will not squirt fluid


Make sure it is above 2 degrees centigrade and not frozen.
Check and fill up fluid reservoir with wash solution.
If there is any evidence of mould growth in the bottle - it needs removing and the bottle and pump washing out.
Check operation of pump by supplying 12V to connectors.
Test pump connectors in car for 12V supply (clip on test lamp)
Check fuse in fusebox.

The problem should be easily found by checking these points.

Dec 25, 2010 | 2005 Chevrolet Malibu

3 Answers

Just bought a 1987 Iroc Z. Need to know why my


look at waser bottle and there is a pump . replace the pump very easy to do

Nov 12, 2009 | 1987 Chevrolet Camaro

1 Answer

Windshield washers not working


hi
you will need to check if you can hear the pump runing when you turn the washerfluid button. if you don't hear the pump
check the fuse in the fusebox
if the fuse ok then the pump might be broken or disconnected
if you have a voltmeter check at the connector if you have 12V when you turn the washerfluid button if you do the pump is broken so replace it
if you don't have 12V at the connector terminals then the pump wire is cutted somewhere
Hope this will help you
Good luck

Jun 19, 2009 | 1997 Ford Explorer AWD

1 Answer

Jaguar x type washer failure


it is more likely the wiper switch has bad contacts or the washer pump is defective, go to the pump and have someone hold wash and check for a 12 volt sigal at the washer fluid pump, if no siganl replace the wiper/washer switch, and if u do have the signal at the pump then the pump is defective.

Apr 01, 2009 | 2005 Jaguar X-Type

1 Answer

Windshild liquid is not working, the tank is full


If you are in an area that has been experiencing extreme cold, then the fluid may be frozen in the line. To remedy this, take the vehicle to a carwash and spray the lines with the hot water until the car wash stops (1 quarter's worth). Then try the washer again.

The pump could be malfunctioning. With the key in the accessory position, have someone under the hood listen for the pump running. If the pump runs, you're in warmer climate and no fluid is being sprayed, then your pump may be defective.

Jan 28, 2009 | 2002 Toyota 4Runner

2 Answers

Washer fluid pump not working


just pull out fuses one at a time and see if any are blown, if so just replace.

Dec 15, 2008 | 1999 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

66302 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Fordexpert

Level 3 Expert

5363 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...