Question about 2004 Hyundai Elantra

1 Answer

Can't figure out how to remove the battery from the terminals on my 2004 hyundai elantra. THe posotive port has a weird screw coming out, can't get the cap to budge, looks like terminal may start to leak if I try to move it anymore.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 2,039 Answers

Normally when you loosen the nut on top it supposed to come off the corrosion hold it in place loosend the nut tap it with hammer it should com e off thanks pierre

Posted on Dec 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hyundai Tucson battery cable remove refitting chekenginelight coming how to solve it


How To Replace Battery Terminals - YouTube

? 6:50
https://www.youtube.com/watch?v=KU74feDrnAc
Sep 29, 2013 - Uploaded by TheDIYGuyDOTnet
A video on how to replace the battery terminals or cable ends on your car ... to do so and have before for a sub/amp install on my 04 Tiburon and ..... Battery Cable and Terminal Ends: Checking and Replacing - Duration: 4:19.

How to replace the battery on a Hyundai - YouTube

? 6:13
https://www.youtube.com/watch?v=DWlHE6ShvMI
Feb 6, 2014 - Uploaded by jimthecarguy
How To Replace The Battery On A 2008 Hyundai Santa fe. ... How to Install Replace Change Battery 2001-06 Hyundai Elantra - Duration: 4:01.Missing: refitting

2007 Tucson: How do I re-attach battery cable - CarGurus




Jan 16, 2016 | Hyundai Cars & Trucks

1 Answer

How to replace ignition switch on a hyundai tiburon


Removal & Installation

Specific to:
Hyundai Entourage 2007-2008
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative (-) battery terminal.
  3. Remove the crash pad lower panel (A).

    0996b43f80e41e86.jpg
    enlarge_icon.gifenlarge_tooltip.gif
    Fig. Remove the crash pad lower panel (A)
  4. Remove the 2 screws (A) and the trip switch connector.
  5. Remove the crash fascia panel (B).

    0996b43f80e41e87.jpg
    enlarge_icon.gifenlarge_tooltip.gif
    Fig. Remove the crash fascia panel (B)
  6. Remove the screw with the ignition in the ON position (IG ON) and disconnect the 6P connector.
  7. Remove the ignition switch (A).
  8. Installation is the reverse of removal procedure.

    0996b43f80e41e88.jpg
    enlarge_icon.gifenlarge_tooltip.gif
    Fig. Remove the ignition switch (A)
Specific to:
Hyundai Accent 2006-2008
Hyundai Azera 2006-2008
Hyundai Elantra 2006-2008
Hyundai Sonata 2006-2008
Hyundai Tiburon 2006-2008
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    The negative battery terminalThe crash pad lower panelThe ignition switch after loosening the screw with IG ON and disconnecting the 6P connector
  3. Installation is the reverse of the removal procedure.hope this helps it is off autozone website

Aug 02, 2014 | 2006 Hyundai Tiburon

1 Answer

I put a new battery in my 04' elantra and now it won't start but the horn keeps going off


Pl. make the battery terminals firmly tight.Hope this might help.

Oct 20, 2011 | 2004 Hyundai Elantra

1 Answer

HOW TO REMOVE THE POSTIVE TERMINAL FROM THE BATTERY ON A 2002 HYUNDAI ELANTRA


there is a 10mm bolt on the top of the terminal. or its on the side of the terminal. unscrew it and you should be able to pull the terminal off the battery post.

May 04, 2010 | Hyundai Motor 2002 Elantra

1 Answer

Can you please describe how to install a cd player in a 96 Hyundai Elantra?


Disconnect the negative battery terminal to prevent
an accidental short circuit. Pop out the dimmer
switch panel and remove (1) Phillips screw
exposed. Unsnap the gear shifter trim plate and
remove (1) Phillips screw exposed at the base of
the dash trim bezel. Reach under the driver's
side dash, locate the temperature control cable
and remove the cable from the white plastic
bracket. Position the gear shifter in low, pull the
dash panel away and disconnect all wiring harnesses.
Remove the trim bezel (the temperature
controlcable will be attached). Remove (4)
Phillips screws securing the factory head unit
and disconnect the wiring.

Feb 07, 2010 | Hyundai Motor 1996 Elantra

1 Answer

How to replace 2004 Hyundai Elantra starter


First, disconnect the battery. Then the only part that needs to be removed to access the starter is the rubber air plenum boot between the throttle body and the air filter housing. This allows enough room to get an arm in there to access the 14mm bolts that attach the starter to the transmission. After removing the bolts, the starter can be removed from underneath the car. lower it down as much as possible, and unbolt the power cable. You may have to twist and turn it a bit to get around the support between the engine block and intake manifold, but it will come out.

Feb 05, 2010 | 2004 Hyundai Elantra

1 Answer

Hi there, im trying to figure out where my starter is in my 2004 hyundai elantra


The starter motor is located below and back towards the firewall of the thermostat housing, remove airbox to see it. Easiest way to find it would be to follow the large gauge black (negative) wire leading from your battery, down towards the engine. This will connect directly to the starter.

Jan 24, 2010 | 2004 Hyundai Elantra

1 Answer

Fog lamp replacement on 2008 elantra


1. Disconnect the negative (-) battery terminal. 2. Remove the front side cover screw. 3. Remove the front fog lamp assembly connector (A).

38eda8f.gif 4. Remove the front fog lamp bulb (A).

20279ba.gif

Jun 20, 2009 | 2008 Hyundai Elantra

1 Answer

How to remove brake drum rear wheel 2004 Hyundai Elantra


Jack up rear of car till tire is off the ground.
Remove lug nuts & remove wheel.
Remove phillips screw(s) from drum.
Using a hammer, strike the drum to loosen it from the hub.
Remove drum by simutaneously turning it and pulling it outward away from the vehicle.

Mar 17, 2009 | 2004 Hyundai Elantra

1 Answer

Replacing battery


You need to remove the plastice shield, (3 plastic screws into core support, 1 screw to air filter housing). Under that you will see the battery hold down. Remove the one 12mm bolt and replace battery.

Jun 28, 2008 | 2005 Hyundai Elantra

Not finding what you are looking for?
2004 Hyundai Elantra Logo

Related Topics:

210 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...