Question about 1990 Acura Integra Hatchback

1 Answer

Timing marks Is the hole in the pulley the timing mark for the crankshaft and does that mark sit at 12 o`clock for top dead center?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Acura Master
  • 22,041 Answers

Not sure of what make or model this is ,but if i had car in front of me i would soon sort it ,yes a lot of vehicles use a 8mm hole which lines up with a hole behind for locking wheels in place when fitting the timing belt ,if not sure check keyway and it should point to top of engine,but whatever you do always turn engine 360 degrees by hand before trying to start engine when changing or touching timing belt.Watch a ford engine as they dont have keyways and if bolts not hammered up tight then gearwheels turn when you rev engine ,trust me one piston and 5 valves i broke on one .

Posted on Dec 14, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When setting valve timing at what degrees crankshaft pulley mark be?


Finding TOP DEAD CENTER (TDC) Casually

mgaguru.com/mgtech/engine/cs111a.htm
Other times it needs to be a bit more accurate, like setting the crankshaft straight ... assembled engine, and you can use the timing mark on the crankshaft pulley to ... are 360 degrees apart, or offset by one complete rotation of the crankshaft. With TDC on the compression stroke the intake and exhaust valves are both closed.

Finding top dead center on No.1 cylinder when timing marks ...

answers.edmunds.com > Edmunds Answers
Feb 21, 2010 - The crankshaft on a 4 cycle motor in never 180 degrees off between ... Because of this; the timing mark on the crankshaft pulley will be in exactly the same ... So it isn't necessary to know that distinction when setting ignition timing. ... If the exhaust valve spring is about to become fully relaxed, while the ...

Nov 14, 2015 | Cars & Trucks

1 Answer

How do i get a dead on center


Remove the spark plug of no one cylinder (nearest to the timing belt and alternator pulleys). Use a long screwdriver that fits into the hole so it just touches the top of the cylinder. Turn the crankshaft by hand untill you can feel that the cylinder has reached the highest position. Look at the crankshaft pulley for a mark that should be very near or exactly oposite a simmilar mark on the enjine block. Line up these marks for top dead center (TDC). Should degree markings found to be stamped on the enjine block, the crank pulley mark must be alined with the 0 degree mark.

Jan 11, 2012 | 1995 Toyota Avalon

1 Answer

Timing marks on toyota corolla 2004


#1 cylinder at TDC (top dead center) will put the crankshaft pulley keyway at 12 oclock. You can verify this by checking the notch on the crank pulley to the '0' mark on the plastic cover. Next : CAM sprocket has a letter "E" on it with a hole . This hole lines up with a detent on the head.

Aug 06, 2011 | 2004 Toyota Corolla

1 Answer

Trying to find timing marks for 1995 Toyota Corolla 7a-fe


the timing marks are on the timing cover just above the crankshaft pulley(harmonic balancer)and can be seen with a light either forward or rearward of the top of the pulley.the mark on the pulley is usually just a slot(groove) cut into the pulley that you line up with the marks on the timing cover showing the degrees of timing,note there is before top dead center and after top dead center timing marks shown and the marks that you use is before top dead center.

Apr 06, 2011 | 1996 Toyota Corolla

1 Answer

Como poner la banda de tienpo de un toyota camery


Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence.

Dec 23, 2010 | 1993 Toyota Camry V6

2 Answers

Timing belt alignment


A factory service manual would help, but I'm assuming that if you had one, you probably wouldn't be on this site.

To set the timing, you need to first perform the obvious: remove the accessory drive belts, cam pulley covers, and engine fan and hub. Next you'll need to rotate the engine by hand until the timing marks on the camshaft sprockets and crankshaft are aligned with their corresponding stationary marks. The 0 degree mark on the lower timing belt cover is the timing mark for the crankshaft pulley. There is a mark (small, vertical formed indentation) for the left camshaft pulley on the backing plate behind the pulley near the 1 o` clock position. The same mark exists for the right camshaft pulley only it is on the backing plate near the 8 o`clock position (making it difficult to see). With the crankshaft placed at the zero mark, you can observed where the timing discrepancy exists.

(TIP: Once the right camshaft timing is properly lined up, etch an additional mark on the pulley's face and the backing plate at the 12 o`clock position. This will make it easier to align the pulley for furture adjustments and repairs)

To set the timing correctly, move the crankshaft pulley to 12 deg. BTDC. Being careful to not disturb the position of the crankshaft once it has been moved to that position, remove the crankshaft pulley, lower timing belt cover, timing belt tensioner, and timing belt. Compress the timing belt tensioner and if the original ring pin isn't available to retain the tensioner a small allen wrench can be used to achieve the same results. Line up both camshaft marks and reinstall the timing belt and timing belt tensioner (do not remove the timing belt tensioner tool used to maintain the tensioner piston in a compressed position). When installing the timing belt, be sure to allow the least amount of slack to exisit between the left camshaft pulley and the crankshaft sprocket, but without moving the pulleys.

Next, remove the timing belt tensioner piston retention tool and mount the lower timing belt cover and crankshaft pulley (without fully installing them). Rotate the crankshaft pulley to the 0 deg. mark. If done correctly, moving the crankshaft pulley from 12 deg. BTDC to 0 deg. will remove all remaining slack from the timing belt assembly and the camshaft pulleys and crankshaft pulleys will be lined up with their corresponding marks. Once proper timing has been achieved, install all removed parts.

(Another TIP: I hope it's not necessary, but in case it is, I'll remind you that proper torque of all bolts are necessary as this is an all aluminum engine. Stripping out bolts holes due to over-tightening bolts occurs very easily and become very annoying to deal with [e.g. alternator belts not being able to be tightened completely and constantly squealing every few days, etc.])

Apr 26, 2009 | 1997 Isuzu Rodeo

2 Answers

Need instructions to replace 1993 Toyota Camry Timing Belt


Hi Kmcarroll77

TIMING BELT REPLACEMENT - 2.2L -1993 Toyota Camry

Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence. See Fig. 6 . On MR2, tighten engine
b7619be.jpg
92cabaf.jpg
Hope this helps, don't forget to rate.

Lazaruselite

Feb 25, 2009 | 1993 Toyota Camry V6

2 Answers

Need timing mark settings for 1995 Chevy Cavalier 4 cyl


there are two marks one on the cam gear and one on the crank gear. to line these gears up first no#1 cyclinder has to be on commpession stroke, and at top dead center . remove number one spark plug rotate mtr by bumping the starter with key. install commpession gauge hose in number one spark plug hole, when you bump the mtr and that cyclinder is on the compession stroke you will here the air escape from the hose. then rotate the mtr to top dead center by algining the the mark on crank pulley and pointer on the timing cover . cam mark is at 6 a clock postion and the crank mark is at 12 a clock postion. adjust as needed

Nov 25, 2008 | 1995 Chevrolet Cavalier

2 Answers

2001 kia optima 2.5L setting the timing


TDC stands for Top Dead Center, however it is only to set the cylinder number ! at TDC, if yu know where the timing marks are align the crank pulley mark to the "0" of the timing mark, usually this can be achieved by setting the crank shaft doel pin to twelve 0 clock position.

Oct 17, 2008 | 2002 Kia Optima

Not finding what you are looking for?
1990 Acura Integra Hatchback Logo

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...