Question about 2003 Kia Sorento

Open Question

Glove box striker replacement

What do you have to remove to replace the glove box striker ?

Posted by on

5 Suggested Answers

  • 82 Answers

SOURCE: glove box latch broken

The latch is sold seperately. Call your local dealer with the last 9 of you vin number to get the right color. Most dealers sell at the same MSRP price as all the others in town. I know cause I sell these all the time at my Chrysler dealership.

Posted on Jan 08, 2009

  • 1 Answer

SOURCE: glove box latch is broken cant open it want to

Guess what? Volkwagen makes you buy the entire glove box assembly, including lock and door in gray, black or beige for around $145. No way to fix the latch because it is encased in sealedand glued plastic. Good luck! Mine just broke, also.

Posted on Jun 16, 2009

  • 30 Answers

SOURCE: replace cabin filter 2006 Jetta

as far as i am aware the pollen filter is below the glove box just remove the cover below glove box look up with a lighht and you should be able to see filter houseing

Posted on Aug 10, 2009

Molson02536
  • 3854 Answers

SOURCE: do you have to remove whole dashboard on 96 gmc

  1. Remove the front dash panel by turning the lower screws in a counter-clockwise direction, then unscrewing the single bolt on the lip of the instrument cluster and pulling the panel out. Remove the rear wiper switch and the 4x4 switches, if applicable. Lowering the tilt wheel will allow the panel to be totally removed.
  2. Remove the radio, headlight switch module and glove box by turning their screws in a counter-clockwise direction.
  3. Remove the main dashboard by unbolting it at the front, between the windshield and firewall. There are six to eight bolts holding it in, and, once they are removed, the dash can be pulled away from the firewall. Be careful not to pull too much, as the wiring harness could become damaged.
  4. Drain the coolant system by turning the drain plug on the lower left corner of the radiator and allowing the fluid to fall into the drain pan. Uncapping the radiator can reduce the internal pressure.
  5. Remove the heater core hoses, on the upper left of the engine bay, by pinching their hose clamps with a pair of pliers and pulling them off. Some models will have screw-type hose clamps; turning them counter-clockwise will loosen them. Age and heat may have stuck the hoses to the core nipples, and the hoses can be cut right at these nipples if necessary. Leave enough hose to reconnect the new core.
  6. Unbolt the heater core's mounts with a socket wrench in a counter-clockwise direction. Once the bolts are free, the heater core can be maneuvered toward the windshield and slid out. Some coolant may splash out, so have a towel handy.
  7. Replace the heater core with a new one by sliding it into place and securing the mounting bolts.
  8. Reconnect the heater core's hoses, turn the radiator's drain plug clockwise to close it, then refill the coolant system with a 50/50 percent mix of coolant and water.
  9. Reconnect the dashboard to the firewall, then replace the front dash panel and fasten its instrument cluster screw and bottom bolts.
  10. Crank up the truck and add coolant until the heater core is filled and blowing hot air.
  11. Replace the radiator cap.
The Jimmy uses a coolant-heated radiator core mounted in the dashboard to provide heated air into the passenger compartment. This heater core can become clogged and leak, as it is usually the lowest point in the coolant system and debris settles into it. Replacement of the heater core will take the average of about two hours to complete. Good luck

Posted on Nov 19, 2009

  • 258 Answers

SOURCE: Replace cabin air filter in 2003 Mitsubishi

u should be able to sqeeze the sides of the glove just far enough to get past the stops of the glove box. then u should see the access to the filter

Posted on Feb 10, 2010

Testimonial: "very correct on how to get the glove box off, sadly I still couldn't find the filter. I was told some 2003 Mitsubishi Eclipse's didn't have one(?)"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the computer box located in a 97 avallon


Instructions
    • 1

      Remove the battery cover to access the battery terminals. Disconnect the negative (-) battery cable with the pliers.

    • 2

      Open the glove box door and squeeze the outer part to remove the door. Locate the two screws behind the door to remove the glove box.

    • Sponsored Links

    • 3

      Access the ECU behind the glove box. Remove the electrical connectors by hand; remove the bolts mounting the ECU to the inner dash.

    • 4

      Install the new ECU in the same position. Replace the bolts and reconnect the electrical connectors.

    • 5

      Replace the glove box and the glove box door. Reconnect your battery.

Sponsored Links

Read more: How to Replace a Toyota Avalon ECU ' eHow.com http://www.ehow.com/how_6170111_replace-toyota-avalon-ecu.html#ixzz289jiGlka

Oct 02, 2012 | Toyota Avalon Cars & Trucks

1 Answer

How to replace the cabin microfilter


Hello, I'm sending you exploded view of the glove box and the in cabin micro filter cover illustration. Remove the two upper screws on the glove box and carefully pry metal clips loose.
Disconnect glove box lamp electrical connector. Do not let glove box assembly hang from glove box lamp harness.
Remove three lower screws and remove damper clip from glove box door. Separate glove box housing and passenger instrument lower panel.
Remove three screws and remove in cabin micro filter cover.
Remove in cabin micro filters from front heater and cooling unit assembly.
Note When installing two new in cabin micro filters ensure that the filters are facing in the direction indicated by the direction arrow for the airflow. Direction arrow is printed on side of in cabin micro filters.
Install in cabin micro filter cover. Reinstall glove box.12eb879.gif63a72f6.gif
Thanks

Jul 27, 2010 | 2005 Nissan Quest

1 Answer

Replace pollen filter in 2008 honda odyssey


The pollen filters are located in the HVAC box behind the glove box. While holding the glove box open, unclip the glove box damper (left side). Then remove the glove box stops on each side, flip the glove box down. Pull the pollen filter housing from the blower unit by releasing the clips on both sides. Replace the filter in the housing make sure the arrows printed on the new filter are pointing down. Reinstall all removed parts. -hope this helps.

Mar 02, 2010 | 2007 Honda Odyssey

1 Answer

How to replace heater core on 1995 eldoado


You first remove the bottom dash panel on the passenger side. Then remove the glove box (6 screws). remove the little panel on the back of the back of the glove box and disconnect the air bag connectors. Disconnect the connectors for the trunk, gas tank and the glove box light. Pull glove box out.

on the passenger side under the hood against the firewall, remove the two hoses connected to the heater core.

now back inside the car.... remove the connectors and airlines connected to the box, remove the lever on top of the black box. remove retaining screws and push out of way. two screws hold cor in. remove and replace. revers ord

Oct 14, 2009 | 1995 Cadillac Eldorado

1 Answer

I need to replace my Nissan Quest 2007 in cabin micro filter


I'm going to send you exploded view of the glove box and the in cabin micro filter cover illustration. Remove the two upper screws on the glove box and carefully pry metal clips loose.
Disconnect glove box lamp electrical connector. Do not let glove box assembly hang from glove box lamp harness.
Remove three lower screws and remove damper clip from glove box door. Separate glove box housing and passenger instrument lower panel.
Remove three screws and remove in cabin micro filter cover.
Remove in cabin micro filters from front heater and cooling unit assembly.
Note When installing two new in cabin micro filters ensure that the filters are facing in the direction indicated by the direction arrow for the airflow. Direction arrow is printed on side of in cabin micro filters.
Install in cabin micro filter cover. Reinstall glove box.12eb879.gif63a72f6.gif

Oct 10, 2009 | 2007 Nissan Quest 3.5 Minivan

1 Answer

Where behind glove box is the cabin air filter? I have it dropped down after releasing elastic cord.


remove the glove box. (dont take out the 4 striker screws) 2 screws at the top, and 2 at the bottom. after that you will see a panel maybe 1.5"" by 8" take that panel out (1 bolt) and slide the filters out. there are 2 because if it was 1 big one, you could not easily get it out.

Aug 30, 2009 | 2004 Nissan Titan

1 Answer

2006 Hyundai Sonata 3.3 engine - cabin filter replacement


It should be the same general procedure as the 02. Open Glove box and remove contents. Remove glove box stops and or glove box shock on side. With the glove box swung out of the way remove the panel that covers the air filter. Remove and replace filter. Reinstall cover, and glove box stops.

May 10, 2009 | 2006 Hyundai Sonata

1 Answer

Already have cabin filter, need to know how to install it.


Remove all of the contents in the glove box. Remove the glove box door support. Open the glove box. Squeeze the sides of the glove box inward, to drop the box door open further. The cabin air filter is in a small rectangular box, behind the glove box.

May 05, 2009 | 2004 Toyota Avalon

2 Answers

Blower motor location for 2000 Caravan


The motor is located just under the glove box on the passenger side. I remove the glove box then the panel below the glove box. I also go ahead and pull back the carpet and the padding under the motor. It is held in place by 3-4 bolts that take a 7-8 millimeter socket. I use a swivel extension for the back bolts. The motor with the fan blade attached is a tight fit, just keep wiggling and pulling it should come out. Try to remove the old moter without cracking the fan blade, because sometimes the replacement motor doesn't come with a blade

Sep 17, 2008 | 2000 Dodge Caravan

2 Answers

I have a 2005 Subaru Outback Legacy with a glove box that is stuck closed. The hasp for opening the glove box still moves, but does not seem to release the glove box itself. Any ideas as to how to get...


hello first thing to check is were the box mounts at the bottom of the door hinge assembly undo the screws you should be able to lift the door enough to release the lock inside goodluck

Sep 14, 2008 | Subaru Outback Cars & Trucks

Not finding what you are looking for?
2003 Kia Sorento Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

yadayada
yadayada

Level 3 Expert

64034 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...