Question about 2001 Ford Mustang

1 Answer

I need to adjust the beam of light on my headlight.

We took the whole headlight off and are looking for the particular spot to adjust the beam of light.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 229 Answers

Look into the assy with a high powered flashlight you will see phillips head screws or torx head that will allow you to ajust up down sideways.

Posted on Dec 14, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Adjust headlights 1995 GMC


Here are directions....
  1. Park the vehicle on a level surface, with the fuel tank about 1 / 2 full and with the vehicle empty of all extra cargo (unless normally carried). The vehicle should be facing a wall which is no less than 6 feet (1.8m) high and 12 feet (3.7m) wide. The front of the vehicle should be about 25 feet from the wall.



0996b43f8022cced.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 5: Location of the aiming screws on most vehicles with sealed beam headlights


0996b43f8022ccee.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 6: Dual headlight adjustment screw locations-one side shown here (other side should be mirror image)


0996b43f8022ccef.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 7: Example of headlight adjustment screw location for composite headlamps

  1. If aiming is to be performed outdoors, it is advisable to wait until dusk in order to properly see the headlight beams on the wall. If done in a garage, darken the area around the wall as much as possible by closing shades or hanging cloth over the windows.
  2. Turn the headlights ON and mark the wall at the center of each light's low beam, then switch on the brights and mark the center of each light's high beam. A short length of masking tape which is visible from the front of the vehicle may be used. Although marking all four positions is advisable, marking one position from each light should be sufficient.



0996b43f8022ccf0.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 8: Low-beam headlight pattern alignment


0996b43f8022ccf1.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 9: High-beam headlight pattern alignment

  1. If neither beam on one side is working, and if another like-sized vehicle is available, park the second one in the exact spot where the vehicle was and mark the beams using the same-side light. Then switch the vehicles so the one to be aimed is back in the original spot. It must be parked no closer to or farther away from the wall than the second vehicle.
  2. Perform any necessary repairs, but make sure the vehicle is not moved, or is returned to the exact spot from which the lights were marked. Turn the headlights ON and adjust the beams to match the marks on the wall.
  3. Have the headlight adjustment checked as soon as possible by a reputable repair shop.

Jan 26, 2014 | 1993 GMC Sierra K1500

1 Answer

How to align headlights


Are your headlights beams too high? too low? Then bear with me and maybe I can help
Horizontal headlight adjustment is easy. See the screw on the inside top of each light? turn the screw left and your headlight beam goes outward; turn the screw right and the beam goes inward, (toward the center.)
Okay now Vertical adjustment is a little more involved. Start by removing the corner lens; take out the screw on top of the headlight and pull the corner lens forward. This will allow you to access two 10mm bolts holding the headlights in on the sides.
Remove those, along with one 10mm nut on the backside of the headlight assembly (near where your bulbs plug in). Remove your headlight bulbs carefully - I usually put a paper towel around them to protect them from dirt and oil. Now the only thing holding your light housings on are the horizontal adjustment
screws. Just slide the screws out from the lens, and then remove the headlight from the car.
If you look at your headlights now, there is another screw that looks just like the horizontal adjustment screw.
In order to adjust this, you need to remove the 10mm bolt labeled "A".
Now slide the plastic headlight base off of that bolt. The whole plastic base will now be free to swivel on the adjustment screw. What you need to do now is to turn the plastic base around the screw; if you turn it clockwise or right, it will lower your headlight beam when reinstalled. If you turn it left, it will raise the beams.
I ended up only turning each side lower by one revolution. You shouldn't need more than one or two turns. It also becomes hard to slide the housing back over the "A" bolt after two turns. If
in doubt about whether the beams will be raised or lowered, on the final pic you can see the clean area of the bolt on the left side. if you lengthen this side, it causes the beam to go down.
Its really easier to understand as you are doing it, if this does not seem clear. Just use some common sense and you'll see what I mean.
Installation is the reverse of removal.

Dec 22, 2013 | 1993 Mazda MX-6

2 Answers

My lights are not see properly if i dip my lights i can only see in a distance of 5mitres but if i beam mylights i can see a distance of 9 to 10 mitres its a toyota corolla ae91 please help me


Your headlights need aiming correctly. There are screws next to the headlight the achieve this . Park the car on level ground about 2 meters (6feet) from a solid wall and turn the lights on to high beam. You will see the centre of the beam measure the height from the floor to the center of the headlight and mark this on the wall directly in front of the vehicle. The center of the beam has to be adjusted to to this point.Don't worry about low as the beam for low is set by the bulb and is correctly positioned in relation to high at all times

Feb 07, 2013 | 1990 Toyota Corolla

1 Answer

How do i adjust the head lights on a 1997 grand marquis


AIMING THE HEADLIGHTS

On 1989-91 vehicles, the headlights can be aimed using the adjusting screws located above and to the side of the headlight bulbs. A rough adjustment can be made while shining the headlights on a wall or on the rear of another vehicle, but headlight adjustment should really be made using proper headlight aiming equipment.
On 1992-98 vehicles, the aerodynamically styled headlights necessitate the use of headlight aiming kit 107-00003 or equivalent. The adjustable aimer adapters provided in the kit must be used to aim the headlights. Adjustment aimer adapter positions are moulded into the bottom edge of the headlight lens. Set and lock the adjustable adapters, attach each adapter to its mechanical aimer and aim the headlights according to the instructions in the kit.
Headlight aim adjustment should be made with the fuel tank approximately half full, the vehicle unloaded and the trunk empty, except for the spare tire and jacking equipment. Make sure all tires are inflated to the proper pressure.
The headlights must be properly aimed to provide the best, safest road illumination. The lights should be checked for proper aim and adjusted as necessary. Certain state and local authorities have requirements for headlight aiming; these should be checked before adjustment is made.

CAUTION About once a year, when the headlights are replaced or any time front end work is performed on your vehicle, the headlight should be accurately aimed by a reputable repair shop using the proper equipment. Headlights not properly aimed can make it virtually impossible to see and may blind other drivers on the road, possibly causing an accident. Note that the following procedure is a temporary fix, until you can take your vehicle to a repair shop for a proper adjustment.
Headlight adjustment may be temporarily made using a wall, as described below, or on the rear of another vehicle. When adjusted, the lights should not glare in oncoming car or truck windshields, nor should they illuminate the passenger compartment of vehicles driving in front of you. These adjustments are rough and should always be fine-tuned by a repair shop which is equipped with headlight aiming tools. Improper adjustments may be both dangerous and illegal.
For most of the vehicles covered by this guide, horizontal and vertical aiming of each sealed beam unit is provided by two adjusting screws which move the retaining ring and adjusting plate against the tension of a coil spring. There is no adjustment for focus; this is done during headlight manufacturing.
Because the composite headlight assembly is bolted into position, no adjustment should be necessary or possible. Some applications, however, may be bolted to an adjuster plate or may be retained by adjusting screws. If so, follow this procedure when adjusting the lights, BUT always have the adjustment checked by a reputable shop.
Before removing the headlight bulb or disturbing the headlamp in any way, note the current settings in order to ease headlight adjustment upon reassembly. If the high or low beam setting of the old lamp still works, this can be done using the wall of a garage or a building:
  1. Park the vehicle on a level surface, with the fuel tank about 1 / 2 full and with the vehicle empty of all extra cargo (unless normally carried). The vehicle should be facing a wall which is no less than 6 feet (1.8m) high and 12 feet (3.7m) wide. The front of the vehicle should be about 25 feet from the wall.

See Figure 6


1ad3b8e.jpg
Fig. 6: Example of headlight adjustment screw location for composite headlamps
  1. If aiming is to be performed outdoors, it is advisable to wait until dusk in order to properly see the headlight beams on the wall. If done in a garage, darken the area around the wall as much as possible by closing shades or hanging cloth over the windows.
  2. Turn the headlights ON and mark the wall at the center of each light's low beam, then switch on the brights and mark the center of each light's high beam. A short length of masking tape which is visible from the front of the vehicle may be used. Although marking all four positions is advisable, marking one position from each light should be sufficient.

See Figures 7 and 8


9018da5.jpg
Fig. 7: Low-beam headlight pattern alignment


fa6b141.jpg
Fig. 8: High-beam headlight pattern alignment
  1. If neither beam on one side is working, and if another like-sized vehicle is available, park the second one in the exact spot where the vehicle was and mark the beams using the same-side light. Then switch the vehicles so the one to be aimed is back in the original spot. It must be parked no closer to or farther away from the wall than the second vehicle.
  2. Perform any necessary repairs, but make sure the vehicle is not moved, or is returned to the exact spot from which the lights were marked. Turn the headlights ON and adjust the beams to match the marks on the wall.
  3. Have the headlight adjustment checked as soon as possible by a reputable repair shop.

Hope thats helped (remember rated this) Good luck.

Jan 24, 2010 | 1997 Mercury Grand Marquis

5 Answers

How do i adjust my headlingt on a 2001 suzuki xl7


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Nov 14, 2009 | 2001 Suzuki Xl 7

1 Answer

How do you align or focus headlights beams that are to


AIMING THE HEADLIGHTS

The headlights must be properly aimed to provide the best, safest road illumination. The lights should be checked for proper aim and adjusted as necessary. Certain state and local authorities have requirements for headlight aiming; these should be checked before adjustment is made.

CAUTION About once a year, when the headlights are replaced or any time front end work is performed on your vehicle, the headlight should be accurately aimed by a reputable repair shop using the proper equipment. Headlights not properly aimed can make it virtually impossible to see and may blind other drivers on the road, possibly causing an accident. Note that the following procedure is a temporary fix, until you can take your vehicle to a repair shop for a proper adjustment.
Headlight adjustment may be temporarily made using a wall, as described below, or on the rear of another vehicle. When adjusted, the lights should not glare in oncoming car or truck windshields, nor should they illuminate the passenger compartment of vehicles driving in front of you. These adjustments are rough and should always be fine-tuned by a repair shop which is equipped with headlight aiming tools. Improper adjustments may be both dangerous and illegal.
For most of the vehicles covered by this guide, horizontal and vertical aiming of each sealed beam unit is provided by two adjusting screws which move the retaining ring and adjusting plate against the tension of a coil spring. There is no adjustment for focus; this is done during headlight manufacturing.
Because the composite headlight assembly is bolted into position, no adjustment should be necessary or possible. Some applications, however, may be bolted to an adjuster plate or may be retained by adjusting screws. If so, follow this procedure when adjusting the lights, BUT always have the adjustment checked by a reputable shop.
Before removing the headlight bulb or disturbing the headlamp in any way, note the current settings in order to ease headlight adjustment upon reassembly. If the high or low beam setting of the old lamp still works, this can be done using the wall of a garage or a building:
  1. Park the vehicle on a level surface, with the fuel tank about 1 / 2 full and with the vehicle empty of all extra cargo (unless normally carried). The vehicle should be facing a wall which is no less than 6 feet (1.8m) high and 12 feet (3.7m) wide. The front of the vehicle should be about 25 feet from the wall.

fbcb5a7.jpg

Fig. : Location of the aiming screws on most vehicles with sealed beam headlights


97dee4f.jpg

Fig. : Dual headlight adjustment screw locations-one side shown here (other side should be mirror image)

9a545e8.jpg

Fig. : Example of headlight adjustment screw location for composite headlamps
  1. If aiming is to be performed outdoors, it is advisable to wait until dusk in order to properly see the headlight beams on the wall. If done in a garage, darken the area around the wall as much as possible by closing shades or hanging cloth over the windows.
  2. Turn the headlights ON and mark the wall at the center of each light's low beam, then switch on the brights and mark the center of each light's high beam. A short length of masking tape which is visible from the front of the vehicle may be used. Although marking all four positions is advisable, marking one position from each light should be sufficient.

031bc2f.jpg

Fig. : Low-beam headlight pattern alignment

758eed8.jpg

Fig. : High-beam headlight pattern alignment

  1. If neither beam on one side is working, and if another like-sized vehicle is available, park the second one in the exact spot where the vehicle was and mark the beams using the same-side light. Then switch the vehicles so the one to be aimed is back in the original spot. It must be parked no closer to or farther away from the wall than the second vehicle.
  2. Perform any necessary repairs, but make sure the vehicle is not moved, or is returned to the exact spot from which the lights were marked. Turn the headlights ON and adjust the beams to match the marks on the wall.
  3. Have the headlight adjustment checked as soon as possible by a reputable repair shop.

Hope helped with this information. Good luck (remember rated this help).

Nov 10, 2009 | 1996 Toyota Camry

1 Answer

How do you adjust the headlights on a 1998 ford F250 pickup


AIMING THE HEADLIGHTS
The headlights must be properly aimed to provide the best, safest road illumination. The lights should be checked for proper aim and adjusted as necessary. Certain state and local authorities have requirements for headlight aiming; these should be checked before adjustment is made.

CAUTION About once a year, when the headlights are replaced or any time front end work is performed on your vehicle, the headlight should be accurately aimed by a reputable repair shop using the proper equipment. Headlights not properly aimed can make it virtually impossible to see and may blind other drivers on the road, possibly causing an accident. Note that the following procedure is a temporary fix, until you can take your vehicle to a repair shop for a proper adjustment.
Headlight adjustment may be temporarily made using a wall, as described below, or on the rear of another vehicle. When adjusted, the lights should not glare in oncoming car or truck windshields, nor should they illuminate the passenger compartment of vehicles driving in front of you. These adjustments are rough and should always be fine-tuned by a repair shop which is equipped with headlight aiming tools. Improper adjustments may be both dangerous and illegal.

For most of the vehicles covered by this guide, horizontal and vertical aiming of each sealed beam unit is provided by two adjusting screws which move the retaining ring and adjusting plate against the tension of a coil spring. There is no adjustment for focus; this is done during headlight manufacturing.


Because the composite headlight assembly is bolted into position, no adjustment should be necessary or possible. Some applications, however, may be bolted to an adjuster plate or may be retained by adjusting screws. If so, follow this procedure when adjusting the lights, BUT always have the adjustment checked by a reputable shop.
Before removing the headlight bulb or disturbing the headlamp in any way, note the current settings in order to ease headlight adjustment upon reassembly. If the high or low beam setting of the old lamp still works, this can be done using the wall of a garage or a building:

Park the vehicle on a level surface, with the fuel tank about 1 / 2 full and with the vehicle empty of all extra cargo (unless normally carried). The vehicle should be facing a wall which is no less than 6 feet (1.8m) high and 12 feet (3.7m) wide. The front of the vehicle should be about 25 feet from the wall. 5374ba7.jpg

Fig. Example of headlight adjustment screw location for composite headlamps


If aiming is to be performed outdoors, it is advisable to wait until dusk in order to properly see the headlight beams on the wall. If done in a garage, darken the area around the wall as much as possible by closing shades or hanging cloth over the windows. Turn the headlights ON and mark the wall at the center of each light's low beam, then switch on the brights and mark the center of each light's high beam. A short length of masking tape which is visible from the front of the vehicle may be used. Although marking all four positions is advisable, marking one position from each light should be sufficient. 30c25df.jpg

Fig. Low-beam headlight pattern alignment


683f51e.jpg

Fig. High-beam headlight pattern alignment

If neither beam on one side is working, and if another like-sized vehicle is available, park the second one in the exact spot where the vehicle was and mark the beams using the same-side light. Then switch the vehicles so the one to be aimed is back in the original spot. It must be parked no closer to or farther away from the wall than the second vehicle. Perform any necessary repairs, but make sure the vehicle is not moved, or is returned to the exact spot from which the lights were marked. Turn the headlights ON and adjust the beams to match the marks on the wall. Have the headlight adjustment checked as soon as possible by a reputable repair shop.
Hope helped with this (remember rated this help) Good luck.

Oct 30, 2009 | 1997 Ford Explorer AWD

2 Answers

2003 volvo s60, how do i adjust headlights


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Jun 18, 2009 | 2004 Volvo S60

2 Answers

Headlight beam adjustment on Chevy Astrovan 4.3L 2001.


with your hood poped look on the framing above the head lights. there are about 2, 1 inch wholes above each headlight. If you look down in them you will see torx shaped studs. One turns up and down the other turns from side to side.

Nov 17, 2008 | 2001 Chevrolet Astro

1 Answer

How to adjust headlight of Honda 2005


open the hood by the lights u will see a hole wth a light symbl near it put a long screwdriver in and turn the click wheel thing that will raise/lower the whole headlight assembly. ADJUST THE LOW BEAMS BECAUSE THE WHOLE ASSEMBLY MOVES HIGHBEAMS ARE NOT AS IMPORTANT

Jun 15, 2008 | 2005 Honda Civic

Not finding what you are looking for?
2001 Ford Mustang Logo

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...