Can't find button under dash to reset/reprogram keyless entry
1997 Subaru Legacy wagon, the button to hold down to reprogram the remote keyless entry is not under the dash at the driver's knee like it is supposed to be. I found the box labelled keyless entry but there's not a button on it to hold down to reprogram the fob.
Re: can't find button under dash to reset/reprogram...
My GPS in my legacy is not working . i have get tin it recalibrate it and it works for about 15 to 20 mints then it goes crazy again. at one point it showed the car driving in the water when i was on the 287 west. how do i fix this ?
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US. click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need. Goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
immobilizer control module under the dash.some vechicles if you replace key remote dealership has to reprogram remotes using diagnostic equipment.try this techinique to synchronize remote transmitter. stand within 5 feet from vechicle .press transmitter lock and unlock buttons simultaneously for 7 seconds . system will lock and unlock doors confirming synchronization. if this dont help dealership has to reprogram remotes.
have you tried to pull the fuse from the alarm. is the alarm a factory or after market. if it is a after market alarm look under the dash on the drivers side there will be the wires to the alarm just pull the fuse. the other thing to do is disconnect the battery every nite
Turn on the keys to 'Acc'. If your Legacy has a CD player, press down and hold on the 'disp' button for one seconds; if not, omit this step. Push down and hold the 'disp' and 'H' buttons; this helps you to adjust the hour entry. The hours will be incremented by one hour; leave the button when the desired hour entry is set. Push down and hold the 'disp' and 'M' buttons to adjust the minute entry. Hold down till the desired minutes entry is set and release it. Turn off the keys to save the set time.
Programming Electronic Door Lock Control System
NOTE: The electronic door lock control processor (14B001) erases all
previous keyless entry remote transmitter (15K601) from memory when the keyless
entry remote transmitters are programmed or reprogrammed. The electronic door
lock control processor can store up to four keyless entry remote transmitters in
To program (or reprogram) keyless entry remote transmitter into the
electronic door lock control processor, perform the following steps:
Turn ignition switch to the RUN position and momentarily short the two
terminals of the program connector taped to the wire assembly and located behind
the glove compartment. All doors should lock and then unlock. Remove shorting
Press any button on keyless entry remote transmitter. All doors should lock
and then unlock to verify the keyless entry remote transmitter has been
programmed. If door locks do not respond, press button again (up to three times
maximum with the same keyless entry remote transmitter).
Repeat the above step to program additional keyless entry remote transmitters
into the electronic door lock control processor (up to four keyless entry remote
Turn ignition switch OFF. All doors should lock and then unlock.
subaru have 2 security codes one for the key/ignition switch(magnetic code)and one for the remote(rolling electronic) the car is reccognising the key but not the remotes signal to the central locking.
try locking the car with the key then pressing and the holding the unlock button on the remote for 30 secs, see if the car unlocks.if not unlock the car etc....or... put key in door and hold over for 30 secs..etc
Under your dash by steering column,by your left knee, is a small 4" x4" box that has a small wire attached. On the end of the wire is a small button. Push the button with the ignition in the on position. It will reset the alarm system. That will stop your lights from flashing. Have a great day.