Question about 1995 Cadillac Eldorado

1 Answer

Tach on my 1995 eldorado is not correct

The tach on my 1995 eldorado does not read properly. Usually it reads zero but when I got to high rpms the tach needle will move up to about 1000 to 2000 rpm. It seems like it works but the calibration is off.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

I have a complete dash for a 95 which should fix it. They are kind of a pain to replace, and the one I have has 91,000 on the odometer.

Dan Lemke
danl@mvn.net

Posted on Jan 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1995 Subaru Legacy (high miles, over 200,000) lurches forward and back when I try to accelerate from ~65 mph to a higher speed. This appears to coincide with going above 3,000 rpm. The tach also goes up...


You will need a computer to accurately read the signals you are getting from the sensors in the engine bay, but my guess is that the MAF sensor may be acting up.

Sep 22, 2013 | Subaru Legacy Cars & Trucks

2 Answers

I have a 1990 chevy camaro and my rpms r high win the car Is not started and win I start the car thay go even higher


Hi, You could have a vacuum leak. Check all hoses that are connected on or near the intake manifold and throttle body. Good luck.

Aug 14, 2011 | Chevrolet Camaro Cars & Trucks

2 Answers

Gas gauge and tach do not read proper readings! What will cause this? The gas guage will peg past full when there is only quarter tank and tach reads 4500 RPM at idle


The gas tank sounds like a bad ground usually located under the car at the gas tank. I do not know but maybe they both tach and fuel gague get their ground from the same place.

Dec 26, 2010 | 2004 Chevrolet Monte Carlo

1 Answer

Tach jumps all over the place driving and idle. works correct sometimes. how to repair?


crank sensor is tied in with the tach. you have problem with crank sensor or electrical problem. the tach reads rpms, if the sensor is bad it throws the rpms way off. this is why you get the jumping in gauge.

May 28, 2010 | 1993 Nissan Pathfinder

1 Answer

My 1995 Jetta GL 2.0L has Intermittent tach problems. Sometimes tach will work normally and then it falls to zero and stays there.Then it might bounce back and forth. Also, how is the tach hooked up?


The most likely problem is that you need a new voltage regulator put in the alternator,the tach runs off of it and when the tach quits i think you will find that the car also stops charging,the brushes for the alternator are in the regulator and a new one usually fixes the problem.

Apr 07, 2010 | 1995 Volkswagen Jetta

1 Answer

Tach jumps around when stepping on gas with little exceleration


can be the cluster unit or ignition module that is at fault. clusters are exchanged units at any cadillac dealer. the ignition module sends the signal for the reading on the tach gauge

Feb 14, 2010 | 1995 Cadillac Eldorado

1 Answer

I've had new plugs and wires installed but my car is still idling high. The RPM is at 10 instead of zero when sitting at a light. Midas says my serpentine belt is cracked. Is the serpentine belt the same...


The serpentine belt is not the same as the timing belt! Not sure how your tach reads but at idle it will never be zero unless the car is not running. The tach tells the engine speed and if it is running you have to get some kind of reading. The idle may need adjusted or a vacuum line could be off but a zero reading at idle at a light is not correct.

Nov 29, 2009 | 1999 Chrysler Sebring

1 Answer

Astroflex 2100 autostart won't start all the time


you need to reprogram the tach as it may be a little stronger or weeker in your current van

Oct 10, 2009 | 2009 Chrysler Town and Country

1 Answer

Defective tachometer and speedometer


Do the following:1)key in the ON position:remove the 7.5 gauge fuse.Tach needle should read "0:". 2)put it back,go on the engine and unplug the green plug on the igniter -the big one,with 5 or 6 wires on it.The needle on tach reading should be zero.If not you have a short circuit on the black wire between that plug and the plug on the conbination meter.3) If the reading is zero with the plug disconnected,the black wire for the tach is short-circuited inside the igniter. I have one available.email daddykouki@gmail.com

May 30, 2009 | 1989 Toyota Corolla 2 Door

3 Answers

Tach and speedometer gauges intermittently stay at zero


Sounds like a problem in the cluster. These years of VW the clusters could be repared but by someone who knows what they are doing seeing it's printed boards.

Oct 29, 2008 | 1995 Volkswagen Jetta

Not finding what you are looking for?
1995 Cadillac Eldorado Logo

Related Topics:

117 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6876 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...