Question about 2002 Jeep Liberty

1 Answer

2wd/4wd dash light indicating oppsite 02 Liberty

I took a apart the center console to clean it really well. Now the dash indicator is displaying wrong. When in 2H it says "Part Time" when in 4H the light goes out ( like it is in 2H). I did not disassemble any electrical, I just took off the console cover.

Any idea of what to do?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

Obviously something got crossed up while it was apart! Either leave it alone and get used to it (I once had a 59Chevy impala that when left turn signal was on, entire dash flashed on and off with signal. I just laughed and left it alone) if it is still functioning properly. OR: take it apart again and look to see what got messed up!
Have fun (stop being such a neat freak!!!! a little dirt is good for the soul !!)

Posted on Dec 17, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 kia sportage light indicates its in 4wd when its in 2wd and tries to go in to 4wd and 2wd off and on


The actuator on the transfer case has a ground short. This is why the light is on. And it will try to shift back and forth, if you have the switch at 2wd.

Oct 03, 2014 | 2000 Kia Sportage

1 Answer

Can't get it out of 4wheel drive


I recently had the same problem and I took the switch out of the dash and took apart the switch and found that the 2wd part had broken .I took the plastic cover for the switch and cleaned the buttons with A Qtip and left the broken plastic piece out .put it back together and instantly I had control of my 4wd.Good luck

Jan 09, 2013 | 1996 Chevrolet Blazer

1 Answer

1992 Pajero 4wd system attempts to engage randomly, 4wd indicator lights blink


Whenever this warning light or any other stays on in the dash it is indicating that the systems control module (or the system sensor in the case of lights like low oil pressure, door open indicators etc.) has detected a fault, it then disables the system (this applies to ABS,TCS, TCM, SRS, TPMS and BCM faults and others) as long as the light is on. You must now have the dealer hook up a special electronic diagnostic tool and "scan" the system for the fault code that is stored for the problem(s)

Legend of Abbreviations. ABS Anti-lock brake system. TCS Traction control system, TCM Transmission control module, SRS Supplemental restraint system, BCM Body control module. TPMS Tire Pressure Monitor System

Oct 31, 2012 | Cars & Trucks

1 Answer

4wd does not work iv changed the 4wd switch but still does work and on the 4wd switch none of the lights come on to tell you if you are in 2wd or 4wd hi or low


the switch is probably from a newer modle truck, although they work the indicator lights don't always work, and check the 4x4 fuse in the fuse panel on the left side of the dash by the drivers door

Nov 07, 2010 | 1999 GMC Sierra

1 Answer

1999 siverado 4wd problem..started having problems coming out of 4wd, pushed 2wd dash indicator said 2wd but not in any gear. put in park, got grinding gear sound shut off engine restarted 2wd active now....


sounds like it might be an encoder moter, but the best thing you can do is take it to a good transmission shop so they can hook up their reader and find out for sure

Feb 06, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

I have an '02 gmc yukon, stuck in 4 low.


Check for a blown fuse. use your manual to find fuse location. you can remove the shift motor and engage it manually, you need to remove front driveshaft.

Dec 31, 2009 | 2003 GMC Yukon

1 Answer

Service 4wd light is coming on but 4wd works fine


i had the same problem in my 99,i replaced the switch assembly on the dash and all is well,hope this helps

Sep 01, 2009 | 1999 GMC Sierra

2 Answers

2005 Jeep Liberty stuck in Part Time 4wd


I questioned the dealer about my 2005 because mine was disengaging what I thought to be rough compared to what I was used to. They told me that I should shift the vehicle into Neutral before shifting the selector. I have also found that shifting between Reverse and Drive a couple of times while stopped has helped as well. By doing these couple of things, I have had no trouble since. I hope this helps as it might at least be something to try.

Jun 17, 2009 | 2005 Jeep Liberty

1 Answer

My 01 Trooper had problems with the TOD starting last winter. When the switch on the dash is engaged the TOD indicator flashes continually at 4hz but the check lite does not come on. I have vacuum at the...


We have a 1998 Trooper that had the same problem. The fix was an electronic switch for the 4WD - a vacuum sensor - on the front axle that just plugs in. You can see it - if you look under the car from the front, it's mounted in the middle of the front axle. It cost $175 from the dealer. We had somebody install it for $50. Don't know where you live, but they are exposed and can corrode. That's what happened to ours. Good luck - hope it's the same problem. This was an easy fix, and we were pleased.

Jul 20, 2008 | 1998 Isuzu Trooper

Not finding what you are looking for?
2002 Jeep Liberty Logo

Related Topics:

204 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

61292 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...