Question about 2002 Ford SVT Focus

1 Answer

Replacement accelerater cable on focus 02 reg

How do I remove and replace the accelerater cable

Posted by on

  • yadayada
    yadayada May 11, 2010

    Have u looked? it is easy.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 4,369 Answers

You may have a badly carboned throttle body that needs cleaning with carb cleaner.

If cable:

Accelerator Cable —1.8L/2.0L Removal

  1. Disconnect the accelerator cable.
    1. Remove the accelerator retaining clip.
    1. Disconnect the accelerator cable.
  2. Detach the accelerator cable from the bracket.
    1. Rotate the cable to release.
    1. Detach the accelerator cable.
  3. Remove the footwell trim panel.
  4. Disconnect the accelerator cable from the pedal.
  5. Attach a draw cord to the accelerator cable to assist with installation.
  6. Remove the accelerator cable.

Posted on Jan 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My vw golf 1.6 16v 02 reg . starts ok but wont accelerat when pressing accelerator


run fault codes and look for MAF/MAP sensors and accelerator position sensor .

Dec 27, 2013 | 1994 Lexus LS 400

1 Answer

Replacing starter 2005 ford focus


starter is located behind the motor under the intake manifold, to replace remove the battery cable & air filter box and remove 2 15mm bolts that go through the bell housing into the starter then get under the car and remove 4 10mm nuts & bolts that attach a plate from intake to the block then remove 1 more 15mm bolt holding starter in and pull it back then nose first down then remove 10mm and 13mm nuts on starter solonoid removing cable and wiggle it out past the half shaft and vualla its out

Jul 08, 2010 | 2005 Ford Focus

1 Answer

MY BOOT KEEPS COMING OPEN ON MY FORD FOCUS X REG


Seems like either your lock needs replacement or some stuff obstructing its locking mechanism.
Try spraying some lubricant or WD-40 on the lock, and see what comes out.

Nov 13, 2009 | 2001 Ford Focus

2 Answers

Accelerater stays on when in gear even with foot of off the pedal,eventually coming down when out of gear.


First, open your hood and get somebody to work the gas pedal while you watch under the hood, and try and determine if it's catching on anything under there. Make sure it's not simply catching on the floor mat or something first. Spray the cable and mechanism with WD40 or any lubricant. If there is nothing obvious, and the lube doesn't help, the cable may be frayed. Inspect it closely. Let me know what you find out.

Nov 01, 2009 | 1997 Ford Escort

1 Answer

Have a 2000 ford focus I need to know how to replace the accelerator cable .It's a duel cam engine the 8th digit on the vin is a 3 if this helps at all.Is this a dealer part or do any auto parts carry


get part at discount from tascafordparts.com.
Please arte higly if this helps.

SECTION 310-02: Acceleration Control 2000 Focus Workshop Manual
REMOVAL AND INSTALLATION Accelerator Cable —2.0L Zetec-E Removal
  1. Disconnect the accelerator cable.
    1. Remove the accelerator retaining clip.
    1. Disconnect the accelerator cable.
  1. Detach the accelerator cable from the bracket.
    1. Rotate the cable to release.
    1. Detach the accelerator cable.
daf02d3.gif
  1. Remove the footwell trim panel.
  1. Disconnect the accelerator cable from the pedal.
11cc349.gif
  1. Attach a draw cord to the accelerator cable to assist with installation. (Important)
fcca753.gif
  1. Remove the accelerator cable.
Installation
  1. NOTE: The rubber grommets must be installed into the bulkhead and throttle body bracket before the accelerator cable is installed into the grommets.
    To install, reverse the removal procedure.

May 03, 2009 | 2000 Ford Focus

1 Answer

2003 ford focus fuel filter replacement


  1. Depressurize the fuel system. For additional information, refer to Section 310-00 .
  2. Disconnect the battery ground cable.
  3. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  4. Disconnect the evaporative emission pipe.
  5. Remove the fuel filter outlet pipe. For additional information, refer to Section 310-00 .
  6. Disconnect the fuel filter inlet pipe. For additional information, refer to Section 310-00 .
  7. Remove the fuel filter and bracket.
  8. Remove the fuel filter.
    1. Remove the bolt.
    1. Slide out the fuel filter.
you may need a special tool to release the qucik connects for the fuel lines from the filter.

Dec 31, 2008 | 2003 Ford Focus

1 Answer

Ford Focus Air Bags


you should go to a specialist for airbags they could be very dangerous to attempt at home. they will be able to check everything is ok.

Dec 10, 2008 | 2001 Ford Focus

1 Answer

Focus Air Bags


why are you replacing-had a accident...I would NOT attempt it on yourown-leave it to a body shop..really..kev-mn.

Dec 10, 2008 | 2001 Ford Focus

1 Answer

Ford focus heating problems


you might like to try replacing your thermostat on the engine!a way to test if it is working properly is to remove the thermostat and place it into boiling hot water ,this way you will be able to see how and if it is working or not,and how you tell is if the spring compresses closed and the valve opens its fine if not then you need to replace it,,hope that helps..goodluck.

Oct 28, 2008 | 2000 Ford Focus

1 Answer

1970 Karmann Ghia /accelerater cable replacement


Congrats on a find.....even if there is bellypan cancer. The replacement is time consuming but not tough for even a novice mechanic. And by belly pan you mean the tunnel bottem plate? Only if you decide to replace the housing for the cable as well. There are aftermarket kits that allow you to attach the proper end to the cable after you push/thread it through an intact housing.

Jul 28, 2008 | 1985 Volkswagen Cabriolet

Not finding what you are looking for?
2002 Ford SVT Focus Logo

Related Topics:

473 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63291 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...