Question about 2003 Toyota Corolla

1 Answer

2007 Corolla Evap problem after overheating

Cooling system fan did not engage due to dirty contacts on Hi-Low relay.
wife let the car overheat to red then shut it off. I repaired the relay and took it to the dealer (who said nothing is wrong) and wanted to charge 95 to check out the check engine light. Codes are related to Evap system.

I reset the computer a couple of days ago and the light came back on today. The car only has 15k and is under warantee.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 93 Answers

Then take it to the dealer since it is under warantee. EVAP codes are serious enviormental. Manufactors normally dont want those getting out.

Posted on Dec 13, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 07 Saturn Relay shows ac off for engine protection but the gauge shows cold. The hoses feel normal. What is happening?


A/C Off For Engine Protection
Refer to Cooling System Description and Operation

DTC P1258: Engine Coolant Overtemperature - Protection Mode Active.
This is something you need to take to a qualified repair shop .
The engine cooling fan system consists of 2 electrical cooling fans and 3 fan relays. The relays are arranged in a series/parallel configuration that allows the powertrain control module (PCM) or engine control module (ECM) to operate both fans together at low or high speeds. The cooling fans and fan relays receive battery positive voltage from the underhood junction block. The ground path is provided at G100.
During low speed operation, the PCM/ECM supplies the ground path for the low speed fan relay through the low speed cooling fan relay control circuit. This energizes the cooling fan 1 relay coil, closes the relay contacts, and supplies battery positive voltage from the cool fan 1 maxifuse® through the cooling fan motor supply voltage circuit to the left cooling fan. The ground path for the left cooling fan is through the cooling fan relay and the right cooling fan. The result is a series circuit with both fans running at low speed.
During high speed operation, the PCM/ECM supplies the ground path for the cooling fan 1 relay through the low speed cooling fan relay control circuit. After a 3 second delay, the PCM/ECM supplies a ground path for the cooling fan 2 relay and the cooling fan relay through the high speed cooling fan relay control circuit. This energizes the cooling fan relay coil, closes the relay contacts, and provides a ground path for the left cooling fan. At the same time the cooling fan 2 relay coil is energized closing the relay contacts and provides battery positive voltage from the cool fan 2 maxifuse® on the cooling fan motor supply voltage circuit to the right cooling fan. During high speed fan operation, both engine cooling fans have there own ground path. The result is a parallel circuit with both fans running at high speed.

Nov 20, 2016 | 2007 Saturn Relay

2 Answers

I have 2007 Suzuki XL7. I replaced radiator and fan assembly. Fans do not work. Is there a relay? If so, where is it?


Most fan and Ac relays are located in the under hood fuse and relay box. Adequately marked in owners manual or on plastic cover

Sep 03, 2016 | Suzuki XL7 Cars & Trucks

1 Answer

Cooling fans not coming on in 2007 chevy equinox


The cooling fans are computer controlled, the engine temperature at which they are turned on is about 225-230F, the signal comes from the ECT sensor. The fans are controlled through a relay in the underhood fuse and relay power distribution box, the location of the fan relay is shown on a sticker on the bottom of the lid over the power distribution box. The fan system is tested by the computer when you run a fault code test with a code reader or a scanner. Do this and see if a fault code comes up. DO NOT OVERHEAT THIS ENGINE OR YOU WILL DO SERIOUS DAMAGE TO THE CYLINDER HEAD GASKETS RESULTING IN A HUGELY BIG REPAIR BILL. Get this repaired ASAP.

Jul 19, 2016 | 2007 Chevrolet Chevrolet Equinox LT

2 Answers

FANS WONT COME ON ,,ALL FUSES,RELAYS AND ELECTRIC FAN MOTORS ARE NEW,,THERMOSTAT IS GOOD,,WHERE IS ELECTRIC FAN TEMP SENSOR LOCATION


op
why not post symptoms first and not a barrage of parts.
must we decode that to a symptom,. kinda hard right.

I will not guess. what is wrong, nor what is not working on your car. now what fans you are talking about, up to 4 fans on cars.

cab blower fan (wild guess blower is ok) and so is HVAC, ?
radiator fans
Condenser fan.

my wild guess to , engine over heats?????????
if yes, the scan it first. no not last FIRST.
it dont work like you think its not a 1988 Samurai.
sorry,
on modern cars, they got smarter, the engine goes
gee the PCM knows water temp why have a fan temp regulator.
hark , now it dont. (saves cash on useless parts)
but has a relay , (well until you have my car and the relay is now 100% electronic, called a huge transistor)
we've used this tech in industry for years, but car makers just learning how still.
i digress. but evolution and history helps diagnosis.
what is there?

Ill look for you, ive posted this 100s of times
the book is 4 bucks to see online. the real deal
lets look now.
XL-7 (the dash matters big time)
answering for , overheats engine, and fans on RAD dead.
(some are staged, PCM brains... now. and also chain ops based on if A/C is on or not) facts.
first I see 2 fans... ok.
the next page shows nice block diagram of the fan system
yup, NOT Simple.

ill post those words for you.
"The engine cooling fan system consists of 2 electrical cooling fans and 3 fan relays. The relays are arranged in a series/parallel configuration that allows the engine control module (ECM) to operate both fans together at low or high speeds. The cooling fans receive positive voltage from the cooling fan relays which receive battery positive voltage from the underhood fuse block.
During low speed operation, the ECM supplies the ground path for the low speed cooling fan relay which is fan 1 relay through the low speed cooling fan relay control circuit. This energizes the low speed fan relay coil, closes the relay contacts, and supplies battery positive voltage from the fan 1 fuse through the cooling fan motor supply voltage circuit to the left cooling fan. The ground path for the left cooling fan is through the series/parallel relay which is fan 2 relay, and the right cooling fan. The result is a series circuit with both fans running at low speed.
During high speed operation the ECM supplies the ground path for the low speed fan relay through the low speed cooling fan relay control circuit. The ECM grounds the high speed fan relay, which is fan 3 relay, and the series/parallel relay, which is fan 2 relay through the high speed cooling fan relay control circuit. This energizes the series/parallel relay coil, closes the relay contacts, and provides a ground path for the left cooling fan. At the same time the high speed fan relay coil is energized closing the relay contacts and provides battery positive voltage from the fan 2 fuse 1 on the cooling fan motor supply voltage circuit to the right cooling fan. During high speed fan operation, both engine cooling fans have their own ground path. The result is a parallel circuit with both fans running at high speed.
When the request for fan activation is withdrawn, the fan may not turn OFF until the ignition switch is moved to the OFF position or the vehicle speed exceeds approximately 16 km/h (10 mph). This is to prevent a fan from cycling ON and OFF excessively at idle.
end quote.

i bet you didnt scan it , like 99.9 % of all posters here dont.
DTC Descriptors
DTC P0480: Cooling Fan Relay 1 Control Circuit
DTC P0481: Cooling Fan Relay 2 Control Circuit
DTC P0691: Cooling Fan Relay 1 Control Circuit Low Voltage
DTC P0692: Cooling Fan Relay 1 Control Circuit High Voltage
DTC P0693: Cooling Fan Relay 2 Control Circuit Low Voltage
DTC P0694: Cooling Fan Relay 2 Control Circuit High Voltage
Diagnostic Fault Information

is the ECT showing overheat, yes no?
if yes, it must operate a fan or 2.
the book even covers all tests for fans dead, in a large truth table.
both the FSM and alldata.com have that, its no secret ,its published in 4 major places.

lets back up
if the engine coolant is low (no that side tank the engine and rad)
the ECT will lie. if that happens the fans may not come one
that is because the ECT is useless measuring air, for water.
that water must touch ECT for ECT to work.
this is FIRST
then scan the ECT does it show overheating, IT must if it IS overheating. fix that next if it lies to you,(IR gun in hand)

The system has staged fans.
i cant find the trip points in my crappyy online pages.
but is like 225f then 250f trips. is my guess...
about. if the engine over heats, check fuses first then scan it.
it will simply tell you why its bad.
eg, fan1 output dead.
or if you hot wire a fan and its dead, then it is.
(only on cars with non modulated fans,,hot wire them,else not.)

now the link to the 4 buck real book.
the non dash XL7 (my guess) you this pick yourself... cant see car.
https://suzukipitstopplus.com/Products/10182-2007-xl7-service-manual.aspx

this is how it really works
the ECU has software that decide trip points for fans.
hard coded, this is. based on how hot it is and if A/C is on not.
its way smarter than 1988 and better.
the DTC errors can see an open line, shorted to ground or stuck 12v.(runs all time error)
(tells you relay is good or not)

25839272-0kjd5huq4lpr130nt243wle5-3-0.jpg no scanner no joy , sorry, tis a fact.....

25839272-0kjd5huq4lpr130nt243wle5-3-2.jpg

Aug 27, 2015 | 2007 Suzuki XL-7

2 Answers

2004 Chevy Monte Carlo 3.4 the a/c stopped blowing,then it started overheating to the red within a couple miles,replaced the thermostat,the relay switch some days it overheats sometimes it runs fine


Are the cooling fans coming on ? What relay switch did you replace ?
The BCM will request low speed cooling fan operation from the PCM under the following conditions:
?€¢
Engine coolant temperature exceeds approximately 103?°C (217?°F).


?€¢
When A/C is requested and the ambient temperature is more than 10?°C (50?°F).


?€¢
A/C refrigerant pressure exceeds 1310 kPa (190 psi).


?€¢
After the vehicle is shut off if the engine coolant temperature at key-off is more than 117?°C (243?°F) and system voltage is more than 12 volts. The fans will stay on for approximately 3 minutes.


The engine cooling fan system consists of 2 electrical cooling fans and 3 fan relays. The relays are arranged in a series/parallel configuration that allows the PCM to operate both fans together at low or high speeds. The cooling fans and fan relays receive battery positive voltage from the engine wiring harness junction block. The ground path is provided at G101.
During low speed operation, the PCM supplies the ground path for the low speed fan relay through the low speed cooling fan relay control circuit. This energizes the FAN CONT #1 relay coil, closes the relay contacts, and supplies battery positive voltage from the FAN CONT #1 fuse through the cooling fan motor supply voltage circuit to the right cooling fan. The ground path for the right cooling fan is through the FAN CONT #2 relay and the left cooling fan. The result is a series circuit with both fans running at low speed.
During high speed operation the PCM supplies the ground path for the FAN CONT #1 relay through the low speed cooling fan relay control circuit. After a 3-second delay, the PCM supplies a ground path for the FAN CONT #2 relay and the FAN CONT #3 relay through the high speed cooling fan relay control circuit. This energizes the FAN CONT #2 relay coil, closes the relay contacts, and provides a ground path for the right cooling fan. At the same time the FAN CONT #3 relay coil is energized closing the relay contacts and provides battery positive voltage from the FAN CONT #2 fuse on the cooling fan motor supply voltage circuit to the left cooling fan. During high speed fan operation, both engine cooling fans have there own ground path. The result is a parallel circuit with both fans running at high speed.
Is your vehicles check engine light lit ?
Is the

Jul 10, 2015 | Cars & Trucks

1 Answer

Overheating


Stuck Relay for electric cooling fan. Dirty connections from Fan relay to cooling fan.

Feb 27, 2014 | 1997 Ford Windstar

1 Answer

Cooling system overheating


The simple answer is that your cooling system needs to be dignosed. There are MANY things that can cause an engine to overheat. It could be simply low on coolant due to lack of proper maintenance. It could be low due to cooling system leaks. It could be a thermostat that is stuck in the closed position (Not very likely, but possible), it could be a broken or badly corroded water pump impeller, It could be a blown head gasket, it could be a malfunctioning engine cooling fan motor or fan clutch.

The only thing that anyone online can do without proper diagnosis, is GUESS which of these things are causing your problem.

Jun 02, 2012 | 1999 Isuzu Rodeo

1 Answer

Overheating my car continuously overheat


CHECK FOR LOW COOLANT LEVEL AND REPLACE THERMOSTAT AND THE RADIATOR PRESSURE CAP.IF CAR OVERHEATING AND COOLING FAN NOT WORKING.CHECK COOLANT FAN FUSE AND RELAY.IF BOTH OKAY,HOT WIRE COOLANT FAN,IF FAN WORKS, PROBLEM COULD BE FAULTY COOLANT TEMPERATURE SENSOR,OR FAULTY PCM, IF COOLING FAN DONT WORK WHEN YOU HOT WIRE FAN.THE COOLING FAN ASSEMBLY NEED REPLACING.

Apr 22, 2011 | 1993 Lexus Es 300

2 Answers

Overheating no water in oil


Check coolant level. If no loss check thermostat. Also check the the thermostatic relay that runs the electric cooling fan for your cooling system to draw air through the radiator. If the will fan will not engage it will overheat in minutes.

Dec 23, 2010 | 1999 Ford Taurus

2 Answers

Overheating ?


check to see if electric fans turn on in front of radiator

Jul 13, 2008 | 1996 Ford Contour

Not finding what you are looking for?
2003 Toyota Corolla Logo

275 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

64286 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...