Question about 1998 Chevrolet S-10 Pickup

1 Answer

Transmission filter install 1998 chevy s10

Is there a clip or something to hold the filter up

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 124 Answers

No there is no clip there is a seal in the hole were the tube goes sometimes it comes out somtimes it does not. There should be a new one in the filter kit. You do not have to replace it if it does not come out. But back to your question, the filter just pulls out and the new one just pushes in. It can not fall out because the pan holds it in.

Posted on Dec 15, 2008

  • mikehumble Dec 19, 2008

    Please rate and give me feed back on how it worked ou for you thanks.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have an 1998 chevy s10 automatic.this morning I noticed transmission fluid on the ground I checked and it comes out from a hose on top of the transmission but I don't see where it hook up?


From what I have read elsewhere: There is an overflow hose on top of transmission behind engine which actually is from the transfer case. Fluid will drip down onto exhaust and eventually catch on fire. Check transfer case for being overfull by taking the top fill plug out. If transmission fluid runs out, I believe the transfer case input shaft seal is shot and needs replaced. Mine caught on fire. I was lucky to get fire out before truck burnt to the ground. If you continue to drive vehicle at have something to put out a fire!!!!

Nov 13, 2011 | Cars & Trucks

1 Answer

I have a 98 chevy s10 4x4 that when in drive the gear indicator "D" flashes. Does this mean anything? Thanks Mike


The flashing D is a trouble code from the electronic transmission controller. The flash pattern can be used to diagnose what the problem is. Something is not right with your transmission. Take it to the dealer or a mechanic and have it tested. Hope this helps, James Booth. PLEASE RATE THIS!!!

May 21, 2011 | 1998 Chevrolet S-10 Pickup

2 Answers

My chevy s10 slips going into over drive. I was


This is a common issue in this trans and is terminal. An overhaul will be necessary

Nov 14, 2009 | 1998 Chevrolet S-10 Pickup

1 Answer

Having problems with chevy s10 replaced fuel pump


Check the cable that goes from your battery to the fuse box the relay that is clicking is on. Check for lose bolts or corrosion of the contacts or something like that. If the relay is clicking it sounds to me like it is a voltage issue going to the relay.

Oct 05, 2009 | 1998 Chevrolet S-10 Pickup

1 Answer

Installing a blower motor in a 98 Chevy Blazer


96 chevy S10 p/u truck 4cyl 2.2 liter
shift solenoid electrical problem

Oct 01, 2009 | 1998 Chevrolet Blazer

2 Answers

Standard transmission fluid type, 1998


auto is dextron III-MANUAL-borg wagner is dextronIII.-new venture nv3500 is GM2345349 synchromesh trans.lub.and nv1500 is GM9985648 sync.trans.lub.and12380672 friction modifier.

May 01, 2009 | 1998 Chevrolet S-10 Pickup

2 Answers

Chevy S10 Pickup Starter. Removed the two bolts


Just changed a starter in a 94 S10 4x4. The only way to remove the starter was to take the passenger side exhaust manifold off and bring the starter out that way. Installation the same in reverse. Hope this helps. Don

Mar 14, 2009 | 1998 Chevrolet S-10 Pickup

4 Answers

1998 Chevy S10 pickup backup lights don't work


Yes it screws in on right side of tramission and you will need a 7/8 inch deep socket to remove it. You may be able to clean the old one once it is removed. There is a little ball thatgets dirty and may you can get by with cleaning it. Good Luck. Ed

Sep 06, 2008 | 1991 Chevrolet S-10 Blazer

Not finding what you are looking for?
1998 Chevrolet S-10 Pickup Logo

330 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

63990 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...