Question about 2006 Ford F 350 Super Duty

1 Answer

2006 F350 Diesel, need to wire up 12v source for camper fridge.

Where do I pick up the 12 V. safely? Should I install an inline fuse?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 196 Answers

Go to the trailer light plug on the truck turn the key on and check for 12 volts at 1 of the terminals some of them are allready wired

Posted on Jan 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Installing a temporary horn button


IF this is really just temporary, locate the wire going to the horn(s)
Find where you`re going to get the +12V feed, direct from the battery, cigarette lighter, spare hot terminal at fuseblock. any place that`s hot with the key switch off.
Connect one wire of the inline fuse holder to the +12V source you have selected.
If you don`t know for sure that the horn(s) are OK run a wire from the other side of the fuse holder to the horn feed, and connect temporarily, it should honk.
If all is well there run that fused wire to one side of your switch and the other side to the horns.
That`s it.

Dec 04, 2013 | Cars & Trucks

1 Answer

Where are the charging inline fuse links located for 2006 f350 diesel 6.0


They should be coming off the back of the alternator,or on the starter(large positive cable),,or follow the positive cable from the battery to a junction,they will be there.

Oct 04, 2013 | 2005 Ford F 350 Super Duty

1 Answer

I hava a ford tape deck i want to install it in my car but i dont want to blow it cause i don t know which wire is hot


Red is usually hot in 12 volt. Black in 110 volt. !2 volt tester is only about a buck at the dollar store. Turn ignition key to ON and test wire. The colors you test from present tape/radio should match the unit you are installing. If you still have doubts, buy a couple of 12v inline fuses and attach them to any wires you are playing with. They are cheap. Black is usually ground in 12v. Other colors usually relate to speakers.

Nov 23, 2010 | 2002 Ford Explorer

1 Answer

I need a switched source of 12 volts.


go to the fuse panel find the fuse that is powered by the ingtion source take a test light turn key on to see which one has power then use that fuse slot the make fuses with a wire connceter on it ofr your power source

Apr 04, 2010 | 2000 Ford F350 Super Duty Super Cab

1 Answer

Need to find fuse for cig and 12v accesory 2004


This fuse is located the cavity 12 for 20AMP / Cigar lighter and OBDII; check your 2004 Ford F350 Owners Manual (page 197).

Hope that helps (remember rated this) Good luck.

Jan 22, 2010 | 2004 Ford F350

1 Answer

2004 2500HD ext cab short box 6.0 L no 12V power


No there is not a inline fues. Have you hooked up the wiring to stud 1? It doesn't come from the factory hooked up.

Nov 25, 2009 | 2005 Chevrolet Silverado

2 Answers

Trailer harness - Red wire has no power


Hi: under the hood in the power distribution box there is a 40 Amp fuse that has to be installed to power up the trailer package. When standing looking from the front left fender it should be at the front right corner, refer to the power distribution diagram on the cover. As well under the box by the spare tire is a plug in type module mounted on the frame. There should be 2 wire harnesses located there, make sure the correct plug in is connected. Hope this helps... please rate suggestion .... ty

Apr 28, 2009 | 2005 Chevrolet Silverado 2500HD 2WD

1 Answer

I bought a camper and am installing an electric brake control in the expedition. The brake controller itself installed easily, since the truck was wired at the factory for this. But at the tail of the...


The other is a 12v supply to charge the TT battery. I had to run off the battery w/inline fuse. Did you install a relay? my battery keeps gettin drained from my prodigy brake controller.

Mar 22, 2009 | 2004 Ford Expedition

1 Answer

12V outlet


Good Day,

There is no "easy" way to do that. However you can pull the factory wires from behind the outlet and re-wire it directly to the battery or constant hot source. If you do this be sure to add a 15 or 20 amp inline fuse to the circuit.

Hope this help.

Sep 11, 2008 | 2006 Hyundai Tucson

Not finding what you are looking for?
Cars & Trucks Logo

196 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...