Question about 2004 Mercury Mountaineer

1 Answer

How to remove the fan from an 04 mountaineer

I need to remove the fan to change the water pump...cannot figure it out. Can you help? Thanks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 124 Answers

This has a thread on fan clutch that you will need a spanner wrench for.

Posted on Dec 13, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove water pump on 2002 mercury mountaineer


You have to start with removing battery neg cable then start pulling fan shroud and fan clutch and then most of the time the radiator has to come out and anything else in front of the water pump. Dont forget to drain radiator into something big enough to hold all the fluid. The thermostat should be replace at the same time

Dec 04, 2015 | Mercury Cars & Trucks

1 Answer

Remove fan from water pump


You need to loosen the fan shroud and then remove the blade from the fan clutch.

Mar 29, 2014 | 2003 Mercury Mountaineer

1 Answer

Take the fan off the water pump


remove the 4 bolts holding the fan to the water pump it will come off

Sep 02, 2012 | 1997 Mercury Mountaineer

1 Answer

How to replace water pump on 97 mountaineer


For water pump replacement i suggest you to check the help link provided below.

click the link below :----

Water pump replacing procedure for all vehicles?

http://technoanswers.blogspot.com/2011/11/water-pump-replacing-procedure-for-all.html
---------

HOW TO REPLACE A WATER PUMP

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-water-pump.html

------------------
How to route Water Pump Belt for 1992 Oldsmobile ?

http://carbeltrouting.blogspot.com/2011/12/how-to-route-water-pump-belt-for-1992.html

---------
How to replace Water Pump on Car ?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-water-pump-on-acura-car.html

---------
How to Remove Water Pump?

http://technoanswers.blogspot.com/2011/12/how-to-remove-water-pump-on-toyota.html

-------
Where is Water Pump located ?

http://technoanswers.blogspot.com/2011/12/where-is-water-pump-located-on-toyota.html

-----------
This will help. Thanks

Feb 12, 2012 | 1997 Mercury Mountaineer

1 Answer

2003 ford explorer is stuck in park, the brake lights are on so i dont think it is something to do with the brake


adobe.gif Printable View (109 KB) TSB
04-22-12
  • GEAR SELECTOR LEVER - INCREASED EFFORT TO SHIFT FROM DRIVE TO PARK
Publication Date: November 1, 2004
FORD: 2002-2005 Explorer, Mountaineer ISSUE: Some 2002-2005 Explorer 4dr/Mountaineer vehicles, may require a greater effort to move the gear selector lever (shift lever) from drive to park. This may be due to a time delay with the brake shift interlock (BSI) pin retraction.
ACTION: To service, replace the BSI switch. Refer to the following Service Procedure.
SERVICE PROCEDURE
  1. Remove the two (2) fasteners supporting the instrument panel knee bolster from below the steering column and remove the cover (Figure 1).

    tb7934b.gif
    Figure 1 - Article 04-22-12

  2. Remove the three (3) fasteners supporting the steering column lower shroud and remove the cover (Figure 2).

    tb7935b.gif
    Figure 2 - Article 04-22-12

  3. Remove the three (3) wiring bundle carrier fasteners from the bottom of the steering column to allow movement while removing the BSI switch. It may be necessary to release the connectors from the multifunction switch (Figure 3).

    tb7936b.gif
    Figure 3 - Article 04-22-12

  4. Remove the BSI fasteners (T-30 on the side and T-20 on the bottom) (Figure 4).

    tb7938a.gif
    Figure 4 - Article 04-22-12

  5. Pull the BSI tab on the bottom of the column downward to help free the BSI from the column housing.
  6. Break the two (2) side tabs off the BSI by the white wiring connector (Figure 5).

    tb7940a.gif
    Figure 5 - Article 04-22-12

  7. Push the locking tab on the white connector towards the wiring to release the connector from the BSI. Be careful not to damage the connector or wiring. If the connector does not free easily, a very small flat screwdriver may be used to help lift the locking tab (Figure 6).

    tb7941a.gif
    Figure 6 - Article 04-22-12

  8. Connect the wiring to the new BSI. Ensure all clips are fully engaged to prevent the connector from pulling free.
  9. Reinstall the BSI onto the steering column and reinstall fasteners (Figure 7).

    tb7942a.gif
    Figure 7 - Article 04-22-12

  10. Check BSI function. With the key in the accessories or run position, press the brake pedal. The BSI pin should retract on brake application, and spring up one (1) second after releasing the brake pedal. Repeat several times.
  11. Reinstall fasteners to connect wiring bundle carrier to the steering column. Make sure all connections to the multifunction switch unit are secured properly.
  12. Reassemble steering column in reverse order. Ensure rubber gap hider around shift lever is properly seated on the shroud.
  13. Cycle the shift lever from park to drive and drive back to park several times to verify improved shift effort.

PART NUMBER PART NAME 1L2Z-3Z719-DA BSI Switch

Feb 15, 2011 | Ford Explorer Cars & Trucks

1 Answer

Changing a waterpump. how do you get the radiator fan blade off?


You need to "hold the fan" (with gloves on) while loosening the four bolts behind the fan blades...the blade and pulley will then pull off exposing the water pump bolts...:)

Dec 08, 2010 | 1999 Mercury Mountaineer

1 Answer

Can someone help me? am traying to change tha wather pump but want some instructions like what to do first,where the pump is located, and so... thanks!!


5.2L and 5.9L Engines
See Figure 6
  1. Disconnect the negative battery cable.
  2. Open the radiator valve and drain the cooling system.
  3. Remove the cooling fan and shroud as an assembly.
  4. Remove the accessory drive belt.
  5. Remove the water pump pulley from the hub.
  6. Disconnect the hoses from the water pump.
  7. Loosen the heater hose coolant return tube mounting bolt and nut and remove the tube. Discard the O-ring.

3833dec.jpg

Fig. Fig. 6: Water pump mounting bolt locations
  1. Remove the water pump mounting bolts.
  2. Loosen the clamp at the water pump end of the bypass hose. Slip the bypass hose from the water pump while removing the pump from the engine. Discard the gasket.

To install:
  1. Clean all gasket mating surfaces.
  2. Guide the water pump and new gasket into position while connecting the bypass hose to the pump. Tighten the water pump bolts to 30 ft. lbs. (40 Nm).
  3. Install the bypass hose clamp.
  4. Spin the water pump to ensure the pump impeller does not rub against the timing chain cover.
  5. Coat a new O-ring with coolant and install it to the heater hose coolant return tube.
  6. Install the coolant return tube to the engine. Ensure the slot in the tube bracket is bottomed to the mounting bolt. This will properly position the return tube.
  7. Connect the radiator hose to the water pump.
  8. Connect the heater hose and clamp to the return tube.
  9. Install the water pump pulley and tighten the bolts to 20 ft. lbs. (27 Nm).
  10. Install the accessory drive belt.
  11. Install the cooling fan and shroud.
  12. Fill the cooling system.
  13. Connect the negative battery cable.
  14. Start the engine and check for leaks.


Hope helps.

Aug 19, 2010 | 1994 Jeep Grand Cherokee

2 Answers

How do you remove the fan from 1998 f150 4.2 liter


how do you remove the fan and fan clutch from 1998 f150 4.2 liter engine. i am trying to replace the water pump but i cannot get the fan to break loose . i cannot figure how to stop pump from turning while trying to loosen the bolt or nut that holds the fan clutch on the water pump shaft . is there a special tool to help me with this

Jul 15, 2010 | 1998 Ford F150 Regular Cab

1 Answer

How to get fan off water pump


go to auto store and rent a speacial tool for removing the large nut on the back side of the fan. the threads are lefty-tighty and righty-loosey. leave belt on to help hold fan.

Dec 27, 2009 | 1997 Mercury Mountaineer

1 Answer

Is it necessary to remove the thermostat housing in order to replace a water pump bypass hose? Mechanic advises that my 2000 Mountaineer's small by-pass hose is leaking. In order to replace it, either the...


in the upper radiator hose to the engine side of an elbow with 2 screws in there is the thermostat and water pump need to remove the fan belt clucht with the fan off the bottom hose that goes from the radiator to the pump to remove the screws remove the pump the pump clean the surface and install the new pump

Aug 07, 2009 | 2000 Mercury Mountaineer

Not finding what you are looking for?
2004 Mercury Mountaineer Logo

Related Topics:

375 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...