Question about 1994 Chevrolet S-10 Blazer

2 Answers

Would not start, i checked the coil for spark, nothing, put on new coil, not fireing, took ecm to parts store, cheks out good, put old coil on, new dis cap&button in , starts,drove about 7 miles,now won't start.

Posted by on

  • 1 more comment 
  • ernest_mcnai Dec 13, 2008

    i don't have a dignostic

  • yadayada
    yadayada May 11, 2010

    U are going to have to test it for trouble codes our u are just guessing.

  • yadayada
    yadayada May 11, 2010

    what trouble codes do u have?

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Check the coil module. If it malfunctions it can send signal that keeps the rotor firing and will burn it and the distributor cap up.

Posted on Feb 24, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Make sure you have power to to coil

Posted on Feb 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

1995 ford ranger onlu sparking to 3 cylinders


The coils are fired by the ECM, check all the wires to the ECM from the coils and make sure the signal is getting through and you don't have a wiring issue at the engine firewall connector on the driver side firewall.

Jun 05, 2016 | 1995 Ford Ranger Supercab

1 Answer

Car cranks but wont start? No spark. Changed ecm relay no help. Ignition harness is good. No fault codes. Battery is good. changed ignition relay, no help. I think its the ECM but need more info to spend...


Yes, the ECM is the last thing to replace after all other possibilities. No spark could be bad ignition coil, bad Ignition Control Module (controls the coil circuits for spark), bad plug wires, the crank and cam sensors (for ECM to determine spark timing).

Check the ICM -it can be tested at a parts store. If good, check the crank sensor.

Mar 16, 2015 | Cars & Trucks

1 Answer

87 oldsmobile toronado not getting any spark


ECM requires both crank sensor signal and cam sensor signal to fire the coils. Check for spark at the plugs first. Check the plug wires, then the coils. Only if you have no spark at any coil would I suspect the ignition module, and even then only if you have a good crank and cam signal. Do you have any codes stored in the ECM? They could help pinpoint the problem.

May 10, 2014 | 1987 Oldsmobile Toronado

1 Answer

I have a '03 Toyota Celica GT-S with a annoying mis-fire. Started small by replacing all spark plugs - nothing. Replaced the MAF sensor - nothing. Took it to a authorized toyota shop & checked...


Replaced the MAF sensor - nothing. Took it to a authorized toyota shop & checked compression which check out good and put the computer on. Computer read mis-fire on cylinder 1, and then multiple misfire (like it would jump around). We went ahead and replaced the fuel injector on cylnder 1 - did not solve problem as when we hook the computer up, misfire seemed tp stay at idle and seem better when running high RMP, but check engine light is on as it never went away. Went ahead and replaced the coil pack to cylinder 1 - nothing. what am i missing?

Feb 06, 2011 | 2003 Toyota Celica

1 Answer

My car will turn over but will not fire and I have an 1996 ss impala lt1


Sorry about you luck. but here goes how to check it. Pour a little gas in the air inlet ( take the hose off the thriolle body.) crank it and you got fire up briefly then you know you got spart but no fuel. If it runs the fuel pump and the amount of gas in the tank are to be checked. Fuel pump fuses and relays, amount of gas in the tank. Let's say it didn't do nothing but crank, Maybe it doesn't have spark. Take a plug wire off the easies plug you can get to put an old plug or a screwdirver in the end of the wire lay it on metal and crnk it and watch for spark. ( don't hold it in your hand as if it is working it's shock you bad enough to kill you, In the worst case) You see spark and it still won't flash start with extra fuel added. Then you'll have to take a plug out to see whats going on in there. With the plug out it could be soaked with gas, antifrezze, oil, or anything else under the sun. But it could be dry and normal looking too. Test this plug in the end of the wire laying on the exhaust maniflod. If no spark your back to that or it sparks your back to gas. But let's say you still can't get it to pop off any. Maybe it over heated and the engine has little or no compression. ( with the plug wire and the plug out of the way put your finger over the hole the plug came out of and crank the motor if it blows your finger out hard its good but if you can hold it it's bad) ( blown engine ) Your not done yet ,! Put a little motor oil in the plug hole and crank it again if the pressure picks up lot it might start if you do the same to all the cyclinders and then with it all put back together start it. (It'll smoke like crazy so be ready for that) But it still might nor start. The timing chain could have skipped and the timings off enough that it won't start. Most likly it doesn't have sprk and the dist. cap is behind the water pump and it's hard to check as you need to remove the water pump to get to it. The coil wire can be removed first though and check for spark at it. No spark and the dist is turning the crank senser and or the ingition module could have failed. Take the module off and that it to the auto parts store and they can test it and sell you a new one if its bad. If you find no spark first then get the module tested before you do anything else. If the crank senser is bad you can unplug it and cross the wires the are in the plug with a paper clip on off on off and the coil should fire with a good module and the key on. If it does change the senser and you have spark and it'll run if you put everthing back together right. The cap and rotor are bad about failing on this car and they're expensive. The coil wire will fire even with a bad cap and rotor so don't jump to this till you getr good spark at the coil and not at the spark plug. Coil wire can fail too. The cars old enough that all the parts are in question till their proven good.

Jul 03, 2010 | 1996 Chevrolet Impala SS

1 Answer

Not firing right on no.4


First check plug and make sure the right plug for this vehicle,make sure that the heat rating for this plug is correct. Your problem could be a wrong heat rating plug been installed. Also make sure that the misfire is due to a bad plug and NOT a bad injector or injector wiring or uneven compression or even bad coil. Check injector wiring and make sure it not shorting or broken. To check injector pulse use a NOID light can be bought at almost any auto parts store like Auto-zone etc. Also compression can be checked with compression guage. A rule of thumb to go by is if any cylinder has more than 10 PSI in difference in compression there is a problem like a burnt valv etc. Here is a n example cyl# 1 170psi cyl#2 176 psi cyl#172psi cyl# 4 150 psi, there is a problem with cylinder # 4 and will cause a miss from cylinder #4. Good luck and thank for using FIX YA

Mar 26, 2009 | 2000 Mercury Grand Marquis

1 Answer

Car will not start has spark and fule


try removing the coil pack and see if its cracked ,it might not be throwing out enough power to spark under compression .

Feb 16, 2009 | 2004 Mazda 3

2 Answers

1988 buick lesabre won't start


they can test your ECM (under the coil pack) at your local parts store

Nov 28, 2008 | 1988 Buick LeSabre

Not finding what you are looking for?
1994 Chevrolet S-10 Blazer Logo

Related Topics:

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...