Question about 2005 Chrysler PT Cruiser

1 Answer

Where is the crank sensor located on 2005 chrysler pt cruiser?

Posted by on

  • 9 more comments 
  • Anonymous Jan 02, 2009

    my 2005 pt cruiser will start just fine and then next time it will not!! I've been taking off the top to that little black box under the hood that the fuses are in the pushing down on all of the fuses, even replaced the one that was listed for the ignition and still it will not start sometimes?? we can't find the problem is there anyone else that has this problem? and if so what fixed it?

  • Anonymous Mar 12, 2014

    pt cruiser knock sensor location

  • Anonymous Mar 13, 2014

    where is the transmission control solenoid located on a 2002 pt cruiser

  • Anonymous Mar 16, 2014

    2004 crankshaft sensor pt cruiser

  • Anonymous Mar 20, 2014

    my 2004 pt cruiser has a bad oil leak when i turn my car on. do i need a new oil sensor

  • Anonymous Mar 20, 2014

    oil sensor location

  • Anonymous Mar 27, 2014

    where are located the oxygen sensors on 2008 chrysler sebring?

  • Anonymous Mar 27, 2014

    Pt cruiser alarm box location 2007

  • Anonymous Mar 27, 2014

    Pt cruiser alarm box location 2007

  • Anonymous Mar 29, 2014

    Connecting a radiator cooling fan to the wire harness in a 2004 Chrysler PT Cruiser

  • Anonymous Mar 30, 2014

    my 2001 PT Cruiser stopped running going down the road and will not start back. will crank but there is no fire to it. I believe it is the crankshaft sensor. where is the crankshaft sensor located on the engine?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,011 Answers

The crank sensor is located on back right side of engine by were the trans. bolts up.is the no start when could or hot?

Posted on Jan 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you troubleshoot a crank sensor on a 2005 pt cruiser


no idea what the code refers to but having to pump the accelerator could mean you have a fuel filter or pump problem .

Nov 24, 2015 | 2005 Chrysler PT Cruiser

1 Answer

2005 PT Cruiser no crank


sounds like the crank position sensor. check continuity and 5volts reference at sensor. you can have it checked by someone with a Good scanner(SNAP-ON). If it happens to start up,drive the car till it wont start up again; unplug the crank position sensor and count to 5 then plug it back in. If it starts then its the crank sensor.(just a quick way to test it and get you home or to a shop)

Jan 01, 2014 | 2005 Chrysler PT Cruiser

2 Answers

Where is crank sensor on 2005 PT Cruiser? It absolutely is not above the oil filter as on 01-03 PT's.


REMOVAL - 2.0, 2.4, 2.4L TURBO
The Crankshaft Position Sensor is in the front of the engine block just under the starter motor (CRANKSHAFT POSITION SENSOR LOCATION).

Disconnect the negative battery cable.
Raise vehicle and support.
On 2.4L SRT-4 remove the lower inner cooler hose from the metal tube.
Remove the Structural Collar (Structural Collar and Bending Strut-(Automatic Transaxle Equipped) ), refer to the Engine, Structural Collar Removal and Installation section.
Unlock and disconnect the electrical connector to the crankshaft position sensor.
Remove the crankshaft position sensor bolt.
Remove the sensor. Arrow points to sensor in picture.


emissionwiz_108.gif

Aug 22, 2011 | 2005 Chrysler PT Cruiser

1 Answer

Were i the crankshaft position sensor located o a 2005 pt cruiser


near the oil filter.. above it...under exhaust manifold one small bolt holds it on. If the is a no start condition look for frayed wiring near crank sensor..... it has a harness that hangs too low on some of those. & rubs on cv shaft

Sep 14, 2010 | 2005 Chrysler PT Cruiser

1 Answer

Timing belt wont tutn on my 2005 pt cruiser 2.4l


Try turning the crank with a socket and a bar. is the tensioner making enough tention

Apr 18, 2010 | 2005 Chrysler PT Cruiser

1 Answer

I have a 2001 pt cruiser need to find where the crank sensor is located 4cyl


It is located next to crankshaft. Just follow spark plug wires to coil pack and module. Then follow from there and they lead directly to crank sensor.

Nov 19, 2009 | 2001 Chrysler PT Cruiser

Not finding what you are looking for?
2005 Chrysler PT Cruiser Logo

Related Topics:

2,947 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...