Question about 1998 Ford F150 Regular Cab

1 Answer

No lights while working on my trailer lights to make sure they were working I lost my brake lights, turn signals and hazard lights. Head lights work and tail lights work when head lights are on, other than that I have nothing. I checked the fuses to turn signals and trailer lights and all were ok.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

Some where you lost the ground for the lights take your time and check things over again and you will find it

Posted on Jan 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Brake lights went out so I changed a blown fuse,now the brake lights wont shut off,so I replaced the brake switch at the pedal and still have the same issue,lights wont go off.


Which fuse did you replace ? The one in the under hood fuse box or one of the two in the I/P fuse box . Do the CHMSL - center high mount stop lamps work correctly ? Here is a description how they work .
Stop Lamps
The STOP LP 25 A fuse in the underhood fuse block supplies battery positive voltage to the normally open stop lamp switch. When the driver presses the brake pedal, the switch contacts close and battery positive voltage is supplied to both the STOP 15 A fuse and the CHMSL 10 A fuse in the I/P fuse block, and to the turn signal/hazard module. The turn signal/hazard module then supplies voltage to both of the trailer rear turn/stop lamp supply voltage circuits. The voltage from the CHMSL 10 A fuse is to the center high mounted stop lamp (CHMSL) and the trailer jumper harness. The voltage from the STOP 15 A fuse is to the stop lamps, throttle actuator control (TAC) module, and the cruise control.
Does yours have trailer light hook up ? If so check trailer wiring connector for corrosion . Also check the turn signal / hazard module .
Does

Aug 23, 2015 | 2003 Cadillac Escalade

1 Answer

I have a 96 chevy blazer and my hazard switch broke and then my turn signals quit working also. so we replaced the turn signal indicator switch (not sure if thats what its called) and hazard switch and...


if you have trailer wiring check it it might be a problem,, or you may have crossed something you have replaced, go through the switch and hazard, use test light / ohm meter

Oct 03, 2013 | 1996 Chevrolet Blazer

1 Answer

Running lights work turn lights and brake lights do not on 2004 navigator-everything works fine on my sons 98 suburban trailer brand new


does the 3rd brake light in the back window work? check fuses if fuses are OK and the hazard lights work, then the turn signal switch may be bad. I dont know what your sons suburban (trailer?)has to do with your navigator?

Aug 30, 2011 | 2004 Lincoln Navigator

2 Answers

1999 ford crown vic dash light running light problem.


Check all the bulbs at tail end for parking and brakes, test grounds and harness for trailer. Check fuses. clean batery terminals, Re instal head light swich properly and make sure all wires conect.
Vitally

Sep 09, 2009 | 2000 Ford Crown Victoria

7 Answers

1996 Chev Silverado K3500 dually, no brake lights


Check at the light socket in the rear, where your lights don't work. You need a test light or a voltage meter, and check to see that you have a groun there, power for your parking light, and power to the brake light. You should have power for the parking lights seeing that it works, and a ground. Just verify that your power for the brakes is getting to the bulb, or not. Just a good place to start.
And you are correct that if the third brake light works (top) your brake light switch is fine.

Aug 19, 2009 | 1996 Chevrolet C3500

1 Answer

Chevy trailer brake problem


Check under hood fuse box make sure L. trailer light fuse isnt blown.

Aug 05, 2009 | 2005 Chevrolet Silverado

1 Answer

98 Jeep Cherokee Classic No Hazards or Signals


Did you use a wiring adapter? this plugs into the stock system to properly power the trailer lights. the other thing is you could have a short to ground in the trailer wiring, especially where it comes out under the jeep.

Jun 13, 2009 | 1998 Jeep Cherokee

1 Answer

1993 Dodge Dakota tail lights dead


dose it have a trailer package? If so check the plugs that go to the trailer plug that was the problem for my truck to goog luck.

Dec 20, 2008 | 1995 Dodge Dakota

1 Answer

2003 Sienna tail lights don't work when headlights are on


Look under the dashboard, next to/above the park brake pedal, for the interior fuse box. It has a black plastic cover. Remove the TAIL fuse, and see if it is blown. This should get you fixed up. Hope this helps, and Thanks for choosing FixYa.

Nov 11, 2008 | 2008 Toyota Sienna

1 Answer

Rear brake lights


they are seperate fuses and also has trailer light relay for tow package models , look for trailer light relay fuse , with key on check them all while your there , if fuse is good , swap with another relay , if that will not work , check bulb housing for melted terminals , lastly have body control module ckecked

Jul 02, 2008 | 2005 Chevrolet Silverado

Not finding what you are looking for?
1998 Ford F150 Regular Cab Logo

218 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...