Question about 2006 Ford Focus
The owners manual does tell you - but it is not obvious.
Unscrew the headlight unit - 1 screw
Push down the 2 retaining clips at the back of the unit to release them (long screwdriver needed
Remove the headlight unit so you can work on it - it will come out - try getting the end in the middle of the car out first rather than the wing side
The rest is easy as you have space to work.
It is easier to put the unit back than take it out apart from the clip on the wing side !
Posted on Feb 19, 2010
There is a rubber cap covering the bulb/socket. pull this off. reach inside and disconnect electrical connector. reach in and turn the locking ring counter clock wise. remove lock ring. grasp back of bulb and pull working up and down. may be a bit difficult because the o ring creates a very tight seal. Reverse directions to install the new one.
Posted on Jan 06, 2009
Hi im a machanic and im doin a bulb change in a ford focus cmax and you have to take the headlight out completely and to do so you will have to take the headlight out and do that you will have to take the bumper off to get to the headlight bults.
Posted on Jan 20, 2009
You have to have a small hand, and first remove the retaining ring that is attached to bulb, then pull out bulb, be careful not to let retainer ring fall off from bulb housing, then plug in bulb and try to screw retaing ring back on. It requires a small hand and delicate touch.
Posted on Feb 06, 2009
Very easy, 2 or 3 minutes.
Remove radiator grille. 2 plastic fittings on top, quarter turn and lift out grille.
Remove complete headlight. Simply lift out 2 L shape retaining pins. Disconnect lead. Ease out complete headlamp unit.
Remove back of headlamp unit to access bulbs. Disconnect lead from bulb while bulb still held by clip. Then release clip to remove bulb.
Reverse process to fit.
Posted on Feb 22, 2009
Try reprogramming it.
1. Turn the ignition from OFF to RUN 4 times within 6 seconds.
2. Turn the ignition OFF. The system will chime to confirm programming mode.
3. Within 20 seconds, press any button on first keyless remote.
The system will chime once to confirm programming.
4. Within 20 seconds, press any button on second keyless remote.
System will chime once to confirm programming.
5. Turn ignition to RUN to exit programming mode.
Posted on May 28, 2009
Most of this solution for changing a headlamp on a ford focus sedan is taken from solution 2's writeup, accept with a few more details that should help changing the bulb assembly for the novice. Pop the hood. At the front of the car, look to the back of the
headlight assembly. There will be a plastic cover on the back. On some
models, you need to unscrew the plastic cap; on others, it just pops or
Remove the plastic cover and then take note of the orientation of the three prong connector on the back of the bulb assembly. This is important because the replacement bulb assembly is going to have to be positioned in the same manner. By noting the orientation before taking out the old assembly, it will be easier to orient the replacement bulb assembly after removal.
There is a small retaining clip that surrounds and holds the bulb in place. Removing the clip can be tricky. On my 2003 Ford Focus sedan, there is a special place to push and release the clip that is above the bulb - perhaps further above than you might think. Push the release clip and it will release the retaining clip from the bulb assembly. Gently pull the retaining clip down and out of the way of the bulb assembly. Pull the original bulb straight out. Remove the three prong connector from the bulb assembly. Connect the three prong connector to the replacement bulb and then orient the three prong connector as the original and push bulb assembly straight back into place. Jiggle the assembly slightly to seat it into the correct position in the headlamp housing and replace the retaining clip to hold the bulb in place. Replace the plastic cover on the back of the headlamp and replacement is complete.
No tools. 10 minutes.
Posted on Jan 18, 2010
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Tips for a great answer:
Aug 26, 2010 | 2003 Ford Focus
Apr 07, 2010 | 2006 Ford Focus
brian_au no 1 solution is wrong.. globe is under a spring clip cover . remove cover, then unplug, then release retaining spring behind the globe. replacement is just process reversal
Sep 18, 2009 | 2005 Ford Focus
Jun 01, 2009 | 2006 Ford Focus
Apr 14, 2009 | 2006 Ford Focus
Mar 25, 2009 | 2006 Ford Focus
Jan 02, 2009 | 2001 Ford Focus
1,055 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: