Question about 1990 Mazda 929

1 Answer

Where is mazda 929 diagnosis connector located?

I want to pull error codes but I cant find the diagnosis connector. I looked everywhere in the engine compartment but could not find it, so any help to locating it is highly appreciated.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 10 Answers

Your ecu check connector is located just near the air cleaner (green 6-pin)
you got also near it the idle speed conector (green 1-pin)
and finally the fuel pump connector (yellow 2-pin)
they are all around one an other

good luck
have a great day

Denis

Posted on Dec 13, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the timing belt on a 1994 mazda 929 3.0 dohc 24 valve engine


Choose:

1994 Mazda MPV timing belt replacement, 6 cylinder DOHC ...

? 3:46
https://www.youtube.com/watch?v=sD2G-NzycvU
Aug 11, 2011 - Uploaded by rsarp
1994 Mazda MPV timing belt replacement, 6 cylinder DOHC 3.0... engine so the valves would not be bent ...

How to replace the timing belt on a 1994 mazda 929 3.0 ...

www.fixya.com/.../t25991928-replace_timing_belt_1994_mazda_929_3...
4 hours ago - how to replace the timing belt on a 1994 mazda 929 3.0 dohc 24 valve... I have a 2000 Mazda 626 4cyl 2.0 liter DOHC engine replacing the timing belt, what ... 2004 6s, 3l. where is the canister purge valve solenoid located?

Where are the timing marks on a 1994 mazda 929 3.0l - Fixya

www.fixya.com/cars/t25991952-timing_marks_1994_mazda_929_3_0l
4 hours ago - where are the timing marks on a 1994 mazda 929 3.0l - Mazda Cars ...1994 Mazda E2000 Cam Timing Mark Positions to Replace Timing Belt ... on a 1994mazda v6 dohc 24 valve engine How to align the timing mark on the ...

Mazda Timing Belt Replacement



Dec 03, 2015 | Mazda Cars & Trucks

1 Answer

Replacing thermostat


First drain radiator fluid, then follow the lower radiator hose from the radiator to the engine. At the end of the hose it will lead to a metal thermostat housing. It's held on by 3 bolts. Remove these 3 bolts and pull away thermostat housing with hose. Take notice of the way the thermostat is positioned before removing. Its best to do all this while laying down, looking up.

Aug 26, 2013 | 1993 Mazda 929

2 Answers

Where is diagnostic port on a 1991 mazda 929


It hasnt got a OBDII but i seem to remember a special plug under the bonnet ,then i gave up and changed a vacumn pipe to a sensor and it run like a dream

Dec 19, 2012 | Mazda Cars & Trucks

1 Answer

How to change the stoplight switch


http://www.autozone.com/autozone/parts/Duralast-Stoplight-Switch/1991-Mazda-929/_/N-itja5Z9cias?itemIdentifier=190051_0_0_Go to brake pedal,remove electrical connector from swtich,look ans see how far the screw is screwed in so you do the same with the new one and adjustment will be minunum.remove screw and install new one and connect electrical connector and push brake pedal in with hand so you can see switch engage,if not engaging right,adjust screw in or out.

Jul 22, 2012 | 1991 Mazda 929

1 Answer

Where is the thermastat located on a 1990 mazda 929


We dont have a diagram, but on 1990 Mazda 929 3.0L FI 6cyl the Thermostat is located under hood, driver side, upper engine area, engine end of upper radiator hose, mounted in coolant outlet housing.

Hope this helps; just keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Have a nice day and thanks for using FixYa.

Jose.

Oct 19, 2011 | 1990 Mazda 929

1 Answer

It wont go into reverse but it will drive even in nuetral


sounds like a motor mount ;let go and the engine/trans. are pulling away from the shift cable.
look under the hood and locate the shift cable and make sure it is in good order.
You may need to loosen the bolt holding it down and adjust the cable .

Sep 19, 2011 | 1991 Mazda 929

2 Answers

Is starter on 1988 mazda 929 hard to replace?


It is a tight fit and may require that you take the motor mounts loose and raise the engine to access the starter. It is definately a job.

Mar 19, 2011 | 1988 Mazda 929

1 Answer

Where is the starter located on my 1992 mazda 929?


its on the back side of your engine, the front side is on the distribuition side (where ur distribuition belt or chain is) right between the backside of ur engine and the front side of ur transmission
hope u can find it it looks like this:
http://www.car-stuff.com/images/part_image/mp-starter.jpg
and the main cable going to it comes out directly from the battery on the positive side.
hope this helps
have fun looking for it

Nov 19, 2009 | 1992 Mazda 929

1 Answer

I'm trying to find out where the module is located on a 1993 Mazda 929


TRANNY AND ENGINE COMPUTERS ARE BEHIND RIGHT KICK PANEL.

Feb 17, 2009 | 1993 Mazda 929

1 Answer

Where is mazda 929 ecu located?


If you mean Engine Control Computer, look up behind glove box on passenger side.

Dec 13, 2008 | 1990 Mazda 929

Not finding what you are looking for?
1990 Mazda 929 Logo

Related Topics:

277 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...