Question about 2006 Ford Freestyle

2 Answers

Cannot get rear brake caliper piston to calapse how is it done

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

You need to buy an ABS brake caliper tool. Or try using molgrips or adjustable plyers becouse the piston needs to screw in to enable it to collapse.

Posted on Dec 13, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,982 Answers

I believe that the rear calipers on your vehicle also serve as part of the parking brake. If so, the piston must be turned and compressed at the same time. There is a neat little "multi-tool you can get from most parts houses to do this with, and... they are pretty inexpensive.

Posted on Dec 13, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to calapse the rear brake calipers


Use C clamp,I put over caliper and calapse.Back could not the same.

May 08, 2013 | 2004 Pontiac Grand Prix

2 Answers

If the brake caliper piston will not go back into the piston bore do it need to be replaced.


try to get it overhauled..because might be it has gone jammed due to dust clottings......else get it replaced due to severe risks of brakes jams

May 06, 2011 | Pontiac G6 Cars & Trucks

1 Answer

Have taken apart but cant get new or old pads back on now. not enough space and part that should move back to make space wont seems to be jammed or siezed. have tried letting out brake fluid but didnt...


  • To install: Front
  1. Compress the piston of the disc brake caliper.
  2. Install the brake pads and caliper assembly.
  3. Lubricate the guide pin. Tighten the guide pin to 16-23 ft. lbs. (22-31 Nm).
8267164.gif

REAR :
  1. Pull out the pad springs and then remove the pads and shims.

To install:

  1. Clean the piston end of the caliper body and the area around the pin holes. Be careful not to get oil on the rotor.
  2. Carefully turn the piston clockwise back into the caliper body (this can be done with a pair of needle nose pliers). Take care not to damage the piston boot.
  3. Coat the pad contact area on the mounting support with a silicone based grease.
A special tool is available to rotate the caliper piston

WARNING

Do not press the piston into the bore as performed on the front disc brakes. Due to the parking brake mechanism, the caliper piston must be turned into the bore.

WARNING

Do not press the piston into the bore as performed on the front disc brakes. Due to the parking brake mechanism, the caliper piston must be turned into the bore.
03ce352.gif

Sep 15, 2010 | 1996 Nissan Maxima

1 Answer

Anything special about changing front pads on audi a3? I've done honda, acura and toyota's.


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!! For front brake pads. For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow: 1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose! 2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper. 3. Now you must thoroughly clean the brake calipers (free of grease). 4. Remove outer brake pad from brake carrier. 5. Pull inner brake pad out of brake caliper piston. 6. Check up the brake fluid level on the reservor, and emptying if neccessary! 7. Push piston back into brake caliper housing. 8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward). 9. Install outer brake pad into brake carrier. 10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm. 11. Install both caps. 12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Aug 25, 2010 | 2007 Audi A3

1 Answer

Replacing rear rotor


YOU NEED A SPECIAL TOOL TO CALAPSE PISTON IN CALIPER OTHER THAN THAT ITS JUST REMOVE WHEEL AND CALIPER AND CALIPER BRACKETT

Jun 27, 2010 | 1995 Nissan Pathfinder

3 Answers

Compressing the rear disc brake caliper on 2008 grand caravan


The rear calipers on these models require a special tool that compresses and turns the piston in at the same time -- most parts stores carry this tool.

It is called a caliper piston press -- and it installs where the pads would go and acts like a c-clamp,when turning handle it will turn the caliper piston backinto the caliper as it compresses it.
Anytime the brake rotor or brake pads are being replaced, the rear caliper piston must be seated (bottomed) to compensate for the new brake rotor or lining. Because the Parking Brake self-adjuster mechanism is attached to the piston, a special seating method is required. The only acceptable method is by rotating the piston back into the bore using Retractor,MILLER Special Tool 8807, . Any other seating method will damage the self-adjuster mechanism.
Good luck and hope this helps.

Mar 07, 2010 | Dodge Caravan Cars & Trucks

1 Answer

How to compress calipers on rear of 93 mercury grand marquis


No a 93 model just presses in like the front.

Apr 03, 2009 | 2006 Ford Freestyle

2 Answers

CANT GET THE PISTON TO RETRACT ON THE CALIPER


With rear brakes the caliper piston must screwed in. It usually has a parking brake mechanism that has to screw out as the pad wears down. When you install a new fat pad, the piston won't retract with normal pressure of a clamp but must be screwed back in on the parking brake screw. This can be done with a long nose pliers but tools are made just for the purpose. I hope this helps.

Feb 04, 2009 | 2006 Ford Five Hundred

1 Answer

REAR BRAKE REPLACEMENT


ase mechanic:

those calipers in the rear have slots on the piston right. that means you have to turn the pistons in clockwise. sometimes a pair of needle nose pliers put in the slots and turn will work, otherwise there is a rear caliper brake tool to turn those pistons in.

Jan 29, 2009 | 1996 Pontiac Grand Prix

1 Answer

Cant get caliper to calapse


Open Bleeder screw. If talking about rear caliper, piston must be turned clockwise, with brake "Cube" to retract.

Aug 08, 2008 | 1996 Cadillac Eldorado

Not finding what you are looking for?
2006 Ford Freestyle Logo

Related Topics:

263 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...