Question about 2002 Daewoo Nubira

4 Answers

Crankshaft position sensor, Nubira

Were is he crankshaft position sensor located on a 2002 Daewoo Nubira

Posted by on

4 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,183 Answers

HI,

I've looked into my refererences and its listed not having one -however it has a camshaft position sensor located on top right side of engine Thanks proton

Posted on Dec 12, 2008

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,806 Answers

Hello Bert
The cam position sensor wire comes from the bundle of wires that go to the fuel rail. It plugs into the socket on the cam position sensor under the cover for the spark plug wires right behind the timing belt between the two cam shaft pullys. The crank shaft position sensor wire comes from the right side of the motor (if you face the belts). It ie the long wire that runs up over the timing belt cover/valve cover. It plugs into a socket under the fuel rail box just above the alternator. You may have to pop the fuel rail out again to get at it

regards

Posted on Dec 12, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 734 Answers

The sensor is located behind your drive belt that is connected to your alternator. In the interior area of this belt you'll see a couple of bolts which cover this sensor. You have to loosen these and I believe there is a belt cover which you must unclip in the area above the sensor cover. At this point you will not be able to get to the sensor. You must unbolt the two bolts on this that hold your engine. Don't worry the weight of the engine will keep itself in place. Now place a hydraulic jack under the engine, with a piece of wood on the part that is to make contact with the engine. Jack the engine up so that the tension is released in the area where you are to remove the sensor. You'll need a pair of needle nosed pliers to remove it, and don't forget which way it will go back in

Posted on Dec 12, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 479 Answers

Under the timming belt cover, sensor runs of tooth wheel on timming belt crank.

Posted on Dec 12, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What. Is. The. Position of. No 1piston. When. Setting. The. Timing. On. Daewoo. Nubira. Cdx. 2 l


after you remove the timing belt covers on the crankshaft gear have a noch face down to alaing tho the oil pump cover on the camshafts have two marks a the top of timing cover

Sep 09, 2014 | 2002 Daewoo Nubira

1 Answer

02 ford taurus crankshaft position sensor location


Its located in the front of the engine mounted to the timing cover near the crankshaft pulley.

Oct 29, 2012 | 2002 Ford Taurus

1 Answer

Where is the camshaft position sensor located on a 2002 daewoo nubira?


  • Right on the front of the cylender head. Remove the connector and the mounting bolt and remove and replace.


ironfist109_439.jpg


  • Hope this helps.

Oct 28, 2011 | 2002 Daewoo Nubira

1 Answer

WHAT IS CORRECT TIMING MARKS FOR TIMING BELT INSTALLATION. 2000 NUBIRA 2.0 DOHC AND CRNKSHAFT MARKS. Thanks Joe


TIMING BELT
Removal
Disconnect negative battery cable. Disconnect intake air temperature sensor connector from intake air duct. Disconnect the air intake tube from the throttle body. Disconnect the breather tube from the valve cover. Remove resonator from throttle body. Remove air filter housing.
Raise and support the vehicle. Remove right front wheel. Remove right front splash shield from wheelwell. Remove serpentine accessory drive belt.
Remove crankshaft pulley bolts. It is NOT necessary to remove crankshaft sprocket center bolt. Remove crankshaft pulley. Lower vehicle.
Support engine assembly from above with Support Fixture (J-28467-B). Remove engine mount bracket from timing belt end of engine.Remove power steering hose clamp bolt, and position hose away from timing belt cover. Remove front timing belt cover. Using crankshaft center bolt, rotate crankshaft one full turn clockwise (as viewed from timing belt end of engine).
Align mark on crankshaft sprocket with notch at bottom of rear timing belt cover. See Fig. 4 . Align camshaft sprocket timing marks with notches on valve cover. See Fig. 5 .
CAUTION: Engine damage could result if camshaft sprockets are not properly aligned with notches on valve cover.
Loosen the automatic tensioner bolt. Use an Allen wrench to rotate tensioner and relieve tension on timing belt. Remove timing belt.
Fig. 4: Aligning Crankshaft Sprocket Timing Mark
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim_4.jpg
Fig. 5: Aligning Camshaft Sprocket Timing Marks
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim2_3.jpg
Installation
Ensure crankshaft and camshaft timing marks are still aligned. Install the timing belt. See Fig. 7 . Turn the timing belt tensioner counterclockwise to tension the timing belt. Turn tensioner until the pointer aligns with the notch on the rear timing belt cover. Tighten automatic tensioner bolt to specification. See TORQUE SPECIFICATIONS .
Using crankshaft center bolt, turn crankshaft clockwise (as viewed from timing belt end of engine) 2 full revolutions. Ensure timing belt tensioner pointer is still aligned with notch.
If timing belt tensioner is correctly aligned, install timing belt cover. See Fig. 3 . Install the engine mount bracket on the timing belt end of engine. Position power steering hose in place, and install clamp bolt. Install crankshaft pulley. Install serpentine accessory drive belt.
Install right front splash shield. Install right front wheel. Install air filter housing and resonator. Connect air intake temperature sensor connector. Connect negative battery cable.
Fig. 7: Identifying Timing Belt Routing
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim3_1.jpg
here

http://www.2carpros.com/questions/daewoo-leganza-2000-daewoo-leganza-timing-marks

Feb 17, 2011 | 2000 Daewoo Nubira

2 Answers

Location of Crankshaft Position Sensor 2002


in the rear of the engine on the drivers side at the top of the transmission bell housing

Jul 08, 2010 | 2002 Nissan Frontier Crew Cab

1 Answer

Jsut want to know where crankshaft position sensor


Hi!!

here are illustrations of the CKP (crankshaft position) sensor in 2.3L and 3.0L.

Note: In the bottom of the 2.3L drawing says Trottle Position (TP) Sensor, this is wrong, It should say CKP Sensor.


2.3L Engine


The Crankshaft Position (CKP) sensor is located to the left of the crankshaft pulley.

0996b43f80202990.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-2.3L engine


3.0L Engine


The Crankshaft Position (CKP) sensor is located just behind the crankshaft pulley on engine block.

0996b43f8020299e.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-3.0L engine

The cost of the sensor is $23 bucks at AutoZone.

If helpful, click below

Apr 15, 2010 | 2002 Ford Escape

2 Answers

2000 Daewoo Nubira camshaft position sensor


on the front under timing belt cover ,back cam ,if its not their then back of head about 3inches along from the gear wheel end

Sep 11, 2009 | 2002 Daewoo Nubira

1 Answer

Crankshaft position sensor


Here is a Pic of the location The arrow points to the CKP (crank position sensor) It is next to the pulse wheel.
008e032.png

Dec 14, 2008 | 2002 Daewoo Nubira

1 Answer

Daewoo nubira 2002


hi there, im guessing your crankshaft sensor has been damaged. its located under the crankshaft pulley.

Aug 25, 2008 | 1999 Daewoo Nubira

2 Answers

CrankShaft Sensor


tha crankshaft sensor is behind the powersterring pump behind the aluminum base

Jul 08, 2008 | 1999 Daewoo Nubira

Not finding what you are looking for?
2002 Daewoo Nubira Logo

Related Topics:

210 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...