Question about 1991 Chrysler Imperial

1 Answer

Install headlamp switch

Headlights come on without tail & dash lights.... taillights come on with dash but no headlights... its either 1 or the other... is there a certain way to install the knob into the switch?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Just replace the headlight switch.....I had the exact same problem.....fixed it......

Michael Mauck

Posted on Apr 30, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have no headlights, taillights, cluster lights and speedometer has stop working?


Have you checked applicable fuses for everything except head lamps? The headlamps themselves don't use a fuse. Check the battery junction block under the hood, one of your positive battery cables should go to junction block. If several fusible links check them. My info shows red wire carries battery voltage to head lamp switch for headlamps. The headlamp switch has two voltage circuits, mainly, one for the head lamps, for the other lamps that the switch controls, those smaller lamps are fuse protected.

Dec 02, 2015 | GMC Sierra 1500 Cars & Trucks

2 Answers

1999 dodge intrepid. Dash cluster went out as well as the tail lights. But if i pull and HOLD the highbeam switch dash and taillights work . why?


Hello Mike, I suspect you have a bad multi-function switch that operates your headlights, tail lights, turn signals, wipers and washers.

Oct 13, 2015 | Dodge Cars & Trucks

1 Answer

Need to know if anyone has had a problem with dash lights and tail lights not working


Fault tracing needed;
Test for power
1-To headlamp switch
2-Out headlamp switch w/park and/or headlamps requested on...

Mar 02, 2015 | 1995 Chevrolet Blazer

1 Answer

My 1998 dodge Dakotas headlights went out so I changed the switch and now the headlights work but the taillights don't work. Every other light works except the running lights. Also the light that show


The black wire with yellow tracer is voltage for tail lamps. With the headlamp switch on, any voltage on that wire? Use a test light to check. Also check fuse 14--15amp.

Dec 11, 2014 | 1998 Dodge Dakota

1 Answer

Headlight switch relays


Headlight switch probably the problem. One circuit is shutting off when the other turns on. If it was a fuse or relay, it would just turn off...

May 14, 2014 | 1993 Mazda 929

1 Answer

Fuse keeps blowing dash lights and tail lights dont work jeep cherokee sport 1999


There are several fuses involved. I need to know which one(s). As for the taillights, the primary power source is 20A fuse 17 in the power distribution center. The tan/blk wire connects to the headlamp switch which, in park position, applies +12 volts through 10A fuse 7 in the junction block to the left tail light. The headlamp switch, in park position, also apples +12 volts through 10A fuse 23 in the junction block to the right tail light.

I need to know which fuse is blowing the instrument lights so you will have to follow up

Sep 07, 2012 | 1999 Jeep Cherokee

1 Answer

Taillights will not work


Unplug the connector going to your tail lights. Check for voltage and ground to the connector. If you do not have voltage, check the fuse (locations can be found in your owners manual). If the fuse blown, check to make sure the wiring harness is not rubbing through a the hinge on your trunk ( a common problem). If the fuse is good, suspect a faulty headlamp switch. The headlamp switch supplies seperate system voltages to the headlamps, front marker lights, and tail lamps. One system can fail without affecting the others if the headlamp switch is bad.

Aug 15, 2012 | 1997 Mazda Millenia

1 Answer

Dash lights do not work 2000 ford exploier


All go out at once, first check fuses,then dimmer switch for dash lights, finally headlight switch. To check dimmer switch, pull connection off back, on harness with test light and headlight switch activated, 1 of the leads should have power, if so, use ohm meter on dimmer to make sure it has reading between 0 and some value, if no value, open, dimmer is bad, if there wasn't power then check headlight switch, there should be heavier gauge wire that powers switch and 1 for output to hi/lo switch, smaller gauge wires for tail lamps, dash lights, license plate lamps, parking lights. The color wires from dimmer would correspond to the same colored wires on headlamp switch, probe that connection on headlamp switch with switch engaged and see if you have power, if not replace switch, if so, check wire from switch to dimmer.Now if the lights slowly went from bright one day, to less bright some other day, to not working, then the bulbs are bad... good luck...

May 14, 2012 | Cars & Trucks

Not finding what you are looking for?
1991 Chrysler Imperial Logo

Related Topics:

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...