Question about 2002 Jaguar X-Type

2 Answers

Trouble code p1647

Car runs fine but mil lamp on

Posted by on

  • Brian Grady May 11, 2010

    P1647 Where is the banks? Which is which ...Left /right?

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Hi, i work as a mechanic and have just had this code (p1647)on an 02 2.5 ltr x type. got the definition for 02 banks as well. as there are 2 sensors on each bank i took a look at the live data and it showed a slugish response on sensor two(after the cat). unplugging the sensor in the front cat brought up another code for bank two sensor two so this is obviously the right sensor. changed sensor and sent the car out, hope this helps, jon.

Posted on Dec 31, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 334 Answers

P1647 Linear O2 Sensor Control Chip (Bank 2)
I would say its the oxygen sensor on bank 2 and you would probably have to know which side is bank two either the left or the right
God Bless Greg

Posted on Dec 12, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Do trouble codes show when service engine light is not flashing


You can have trouble codes without a MIL lamp
light on the dash

Need professional scan tool software to access
various modules to check for the codes

Sep 04, 2013 | Buick Cars & Trucks

1 Answer

What is service engine light code 12 mean



READING CODES USING MIL (CHECK ENGINE) LAMP

Be advised that the MIL or CHECK ENGINE light can only perform a limited number of functions and it is a good idea to have the system checked with a scan tool to double check the circuit function.

  1. Within a period of 5 seconds, cycle the ignition key ON - OFF - ON - OFF - ON .
  2. Count the number of times the MIL (check engine lamp) on the instrument panel flashes on and off.

The number of flashes represents the trouble code. There is a short pause between the flashes representing the 1st and 2nd digits of the code. Longer pauses are used to separate individual 2-digit trouble codes.
An example of a flashed DTC is as follows:


Lamp flashes 4 times, pauses, then flashes 6 more times. This denotes a DTC number 46. Lamp flashes 5 times, pauses, then flashes 5 more times. This indicates a DTC number 55. DTC 55 will always be the last code to be displayed.


0900c1528007935b.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: Diagnostic trouble code chart (1 of 2)-1995-97 engines


0900c1528007935c.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Diagnostic trouble code chart (2 of 2)-1995-97 2.0L engines

Jul 26, 2012 | 1995 Dodge Neon

1 Answer

2005 Hyundai Tuscon with the check engine light is on. The car is running fine. I had just put gas in it. The gas cap is securely fastened. I took it in for an oil change. The light still plagues me.


When a 'check engine light' (MIL=Malfunction Indicator Lamp) is turned on, there is a DTC (Diagnostic Trouble Code) set/stored in the ECM/PCM (Engine Control Module/Powertrain Control Module). This code identifies which engine management system component/function experienced a malfunction. Once you pull/read this code, you may begin diagnosis.

Sep 03, 2011 | 2005 Hyundai Tucson

1 Answer

Hi, I have a 2007 Dodge Sprinter & am getting an alert code P2015. It's apparently a sensor malfunction. Can you tell me which sensor is affected by this trouble code?


Code Description onepxblk.gif P2015 Fuel Rail Pressure Sensor Signal Too Low - With Automatic Transmission arrow_right_blacks.gif Printer Friendly P2015 Fuel Rail Pressure Sensor Signal Too Low - With Automatic Transmission Possible Causes Setting Conditions
  • Check for air in the Fuel system
  • Check the fuel pressure
  • Check for leaks in the Fuel Supply system components
  • Fuel pressure solenoid has failed
  • Fuel quantity solenoid has failed
  • Fuel pump has failed
  • Fuel supply is contaminated
Engine running; and the ECM determined that the fuel rail pressure was too low for a given engine speed and load.

This code sets in 1 Trip(s).
This code will turn on the MIL (Malfunction Indicator Lamp) onepxblk.gif Malfunction Indicator Lamp The Malfunction Indicator Lamp (MIL) alerts the driver that the Powertrain Control Module (PCM) has detected an OBD II emission-related component or system fault. When this type of malfunction occurs, an OBD II Diagnostic Trouble Code (DTC) will be set by the PCM. The MIL is located on the instrument cluster and is labeled CHECK ENGINE, SERVICE ENGINE SOON, or is identified with an ISO standard engine symbol (i.e., a picture of an engine).
Bulb Test
Each time the ignition switch is turned to the "on" position, the MIL indicator is illuminated for about 3 seconds (which is a function of the PCM).
MIL Lamp-On Message
Each time the PCM detects an Emissions related fault, the MIL is illuminated to inform the driver that the vehicle needs to be taken in for service.
onepxblk.gif COMPONENT MONITOR DRIVE CYCLE INSTRUCTIONS
  • Do not turn off the ignition switch during the test procedure.
  • All Onboard System Readiness codes are cleared if the battery is disconnected or when the Powertrain Control Module (PCM) is cleared with the scan tool.
  • This drive cycle can be used to determine if the Readiness code for this Monitor will run and complete, and if the Malfunction Indicator Lamp (MIL) will remain off after the vehicle is driven.
  • Operating Ranges: Whenever a range of values is provided, try to operate the vehicle in the middle of the range. For example, if the vehicle speed range is from 45-65 mph, operate the vehicle at as close as possible to 55 mph. If the Short Term fuel trim range is -20% to +20%; try to operate the vehicle near 0%.
  • Scan Tool Data: There are certain Parameter Identification (PID) values that must be within range before this Monitor will "run". It can be helpful to pull up those PID items on the scan tool so an assistant can view them during the test.
  • The Readiness code for this Monitor defaults to "continuous" or "monitoring" because this Monitor runs continuously when the engine is cranking or running.
  • This information is a representation of a Drive Cycle, and may vary due to software revisions to the PCM.
COMPONENT MONITOR PRETEST CONDITIONS
  • MIL is off.
  • Battery voltage between 11-16v.
  • Key on or engine running at idle or cruise speed.
TEST PROCEDURE
  1. Connect the scan tool to the data link connector (DLC).
  2. Start the engine and allow it to run at idle speed for 1-2 minutes.
  3. Accelerate at part-throttle to Cruise speed and maintain that speed for several minutes. Bring the vehicle to a stop, but do not turn off the ignition key.
  4. Check for any diagnostic trouble codes (DTC's) in memory. If any DTC's are set, refer to the appropriate trouble code chart to make the repair. If no DTC's are set, the test is finished. Return to the service bay and turn off the ignition key.

Jul 06, 2011 | 2007 Dodge Sprinter

1 Answer

Malfunction Indicator light stays on on my 2006 Jeep Liberty.\r\nCar runs fine but light has stayed on when operating. I have checked gas cap. How can I turn off dashboard indicator light?


Mil light is coming on because it's registering a dtc (diagnostic trouble code) may or may not be evap/fuel vapor discharge like a loose or faulty seal in your gas cap. Have codes checked at an auto parts store (for free) and they can tell you what code/codes are showing. List them here for solutions. You can also have them erase code and if mil lamp comes on again you know somethings to blame and you need to check it out.

Dec 10, 2010 | 2006 Jeep Liberty

1 Answer

This is an add on from a previous question... 2000 Kia Sportage with 93171K on it. The check engine light is NOT on. It does put out two codes on the OBDII reader. P0443 and P1693. I had been told by the...


Trouble Code: P1693 (2.0L L4 VIN 3 Auto)
MIL CIRCUIT MALFUNCTION Print this code dataprint_icon_codes.gif Number of Trips to Set Code: 2
OBD II Monitor Type: CCM Details
Indicators: MIL Details
Trouble Code Conditions:
KEY ON, AND THE PCM DETECTED AN UNEXPECTED VOLTAGE CONDITION ON THE TCM TO MIL CONTROL CIRCUIT DURING THE CCM TEST.
POSSIBLE CAUSES:
  • MIL CONTROL CIRCUIT IS OPEN
  • MIL CONTROL CIRCUIT IS SHORTED TO GROUND
  • MIL CONTROL CIRCUIT IS SHORTED TO SYSTEM POWER (B+)
  • MIL "BULB" IS OPEN OR MISSING
  • PCM HAS FAILED

Possible Causes: (n/a)
2000 Kia Sportage - G 2.0 DOHC - POWERTRAIN - P1693 Malfunction Indicator Lamp (MIL) Control Circuit

May 12, 2010 | 2000 Kia Sportage

2 Answers

Code p0700


code po700 malfunction indicator lamp circuit malfunction tcm conditions. mil contoll circuit is shorted to ground .check the tcm for any codes in memory that are responsible for the request to turn on the mil lamp.tcm or trouble code malfunction has failed.

Nov 18, 2009 | 2002 Saturn VUE

1 Answer

2005 Pontiac Vibe having trouble shifting 1st 2nd code P2716 MIL


This is most likely due to a bad solenoid pack in transmission. You could have tranny serviced and see if it helps. Poor fluid condition makes valves stick in those.

Aug 14, 2009 | 2005 Pontiac Vibe

2 Answers

What does code 1-p0650 mean?


P0650 Malfunction Indicator Lamp (MIL) Control Circuit Malfunction

Malfunction Indicator Lamp (MIL) is located on the instrument panel. When the ignition switch is turned ON without engine running, MIL will light up. This is a bulb check. When the engine is started, MIL should go off. If MIL remains on, the on board diagnostic system has detected an engine system malfunction.

Possible Causes:
  • Harness or connectors (MIL circuit is open or shorted.)
  • MIL bulb may be faulty
  • May 10, 2009 | Hyundai Accent Cars & Trucks

    1 Answer

    How to retrieve trouble codes on 91 loyale wagon


    mil is the malfunstion indicator lamp (check engine light) there is a connector either under the dash or under the hood near firewall that is normally not plugged in to anything. Use a paperclip to jumper this and the engine light will flash codes. i think the connector is green but check a repair manual to be sure. there are other connectors that you don't want to mess with by accident

    Oct 16, 2008 | 1991 Subaru Loyale

    Not finding what you are looking for?
    2002 Jaguar X-Type Logo

    4,234 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Jaguar Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21981 Answers

    Raygin
    Raygin

    Level 2 Expert

    322 Answers

    yadayada
    yadayada

    Level 3 Expert

    63291 Answers

    Are you a Jaguar Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...