Question about 2004 Mazda 6

1 Answer

Engine of 2005 mazda6 vibrated - 2004 Mazda 6

Posted by on

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 24 Answers

A cracked/broken motor mount can cause engine vibration.

Posted on Feb 25, 2009

2 Suggested Answers

  • 1 Answer

SOURCE: i have mazda6 2005 car , service engine lamp glow

the problem is solved partly, the lamp indication of engime service in front panel is gone OFF , what i do is : i take off the battery head for five minutes and the return it then the lamp goes OFF, but till i feel that the engine not work correctly because of vibration in engine ( not continuoes), i check nozels and fire ignitions they are correct in work , till i want help to solve the engine vibration. thanks

Posted on Dec 12, 2008

greg_margo
  • 1959 Answers

SOURCE: i NEED 2005 mazda6 Serpentine Belt Routing

There are 2 engines for your Mazda 6, a 2.3 and a 3.0. Below are both diagrams:
2.3
e557cdf.jpg

3.0
c9ae9a7.jpg

Posted on Sep 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Had new motor mounts put on dodge neon sxt 2005, now the steering wheel vibrates when ideling, what is this caused by?


if solid mounts where installed then it is engine vibration.
the vibration is from the engine !

Apr 18, 2013 | 2005 Dodge Neon

1 Answer

Mazda6 2005 run on high rpm and engine light


TPS maybe...
or it could be the MAP sensor is bad.

take it to AutoZone and have them do a free diagnostic to be sure.

Sep 19, 2011 | 2005 Mazda 6

1 Answer

I have a 2005 mazda 6. it was 2 qts low on oil, i added oil, the car ran fine but had a slight rattle. 2 days later, i was sitting at a stoplight and the car died. my mechanic says the engine seized. no...


Hi . Unfortunately it's a common problem with mazda6 engine.When they run low on oil the crank shaft tend to get damaged.And some times people tend to top up oil rather than changing oil between 6000 &10000kms .Yep the engine is seized cost less replacing the engine than repairing it.good luck....

Jan 05, 2011 | 2005 Mazda 6

1 Answer

Firing order for 2005 mazda6


This model used 2 engines, a 6 cylinder and a 4 cylinder, here are both.
4 cylinder firing order is 1-3-4-2
Here is the diagram:

emissionwiz_21.gif


Here is the 6 cylinder firing order 1-4-2-5-3-6
Here is the diagram:





emissionwiz_22.gif

Jan 04, 2011 | Mazda MAZDA6 Cars & Trucks

2 Answers

Spark plug wire diagram for 2005 mazda 6


2.3L 4 cylinder? After removing the plastic engine cover, look at the top of the ignition coil.

changesparkplugs003.jpg
It should be numbered 1 through 4.

This is plug number 1 on the engine:

changesparkplugs004.jpg
Just wire them 1, 2, 3 and 4 to the corresponding numbers on the ignition coil.

best wishes

Jan 01, 2011 | Mazda MAZDA6 Cars & Trucks

2 Answers

I NEED 2005 mazda6 Serpentine Belt Routing


There are 2 engines for your Mazda 6, a 2.3 and a 3.0. Below are both diagrams:
2.3
e557cdf.jpg

3.0
c9ae9a7.jpg

Sep 08, 2009 | 2004 Mazda 6

1 Answer

Lookin for Mazda6 3.0L V6 Year 2005 Automatic Workshop Manual on DVD. H.Karlsson hk@heimsnet.is


My Mazda is a 3.0L V6 Year 2005 Grand Touring not 2003.
What I was looking for is if I could buy a Worskhop Manual, printed or on DVD.
The car is in good shape even for 128000 miles because I take good care of it.
The Workshop Manual is meant for future maintenance.
Best Regards
H. Karlsson
hk@heimsnet.is

May 11, 2009 | 2003 Mazda Mazda6

1 Answer

Loud acceleration noise in my 2003 Mazda 6 2.0 auto


one thing to check is rear engine mounting i have had a stone wedged in one and it causes a nasty noise when accelerating

Apr 12, 2009 | 2003 Mazda Mazda6

1 Answer

I have mazda6 2005 car , service engine lamp glow


the problem is solved partly, the lamp indication of engime service in front panel is gone OFF , what i do is : i take off the battery head for five minutes and the return it then the lamp goes OFF, but till i feel that the engine not work correctly because of vibration in engine ( not continuoes), i check nozels and fire ignitions they are correct in work , till i want help to solve the engine vibration. thanks

Dec 11, 2008 | 2004 Mazda 6

Not finding what you are looking for?
2004 Mazda 6 Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...