- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
howdie ther is plastic cover over the engine take this off and then follow the fuel line to it and remove it And May Ask why you doin this Cause ther is no reason on Less you have over 340 km,s on the engine ok just sayin be lookin at the fuel pump pressure and fuel filter before doin this
It located on the cylinder head and connected to the air intake hose, small hose with black color with oneway valve inside from engine to the intake, just know that. ___________- Automobile ECU Sensor Simulation Tool
The fuel pump relay for this 2003 Kia Sorento is located insdie the engine compartment fuse box, open the hood locate fuse box and the relay is there, the fuse box cover should have listing of the location of the relay.
Cabin filters are usually behind the glove boxes or under the wiper under the hood on the passenger side. The glove box has a couple stops usually that just push out and several screws that will need removed depending on the vehicle. It's a little cramped to work on but anyone can do it themselves. You really can just rinse them out and dry them with a compressor and spray a tad of Lysol on them if they're not too bad. For the ones under the hood ...look for fasteners(push-pins) etc. and remove washer lines, weatherstripping(seal) and any other obstacles preventing you from accessing the front edge of the panel that is located under the wiper which you just lip up to get to the filter that is tucked under the panel. Be gentle tugging and pulling and it's an easy task.
The 2006 KIA Sorento is a smaller SUV
with a 3.5-liter V6 engine. This engine uses six spark plugs to run the
engine properly. There will be three spark plugs on each side of the
engine. All six spark plugs will need to be changed at the same time to
ensure that all six are working equally. The spark plugs are in plain
sight on the right and left side of the engine and have rubber wires
connected to the top of each one.
Insert the edge of the spark-plug gapping tool under the meal
arm in the center of the one of the new spark plugs and turn the gapper
until the number .038 is in the center of the metal arm. Repeat this
for all other new spark plugs.
Open the hood of the 2006 KIA
Sorento and remove a rubber wire from one of the spark plugs. Use the
ratchet and spark-plug socket to remove that spark plug from the engine.
Insert the new spark plug into the hole where the old plug
was. Hand-tighten the new spark plug until you are certain it is seated
properly, then tighten it further using the ratchet and spark-plug
socket. Replace the rubber wire to the top of the new spark plug.
Repeat for all other new spark plugs. Once you have replaced
all six spark plugs and replace the rubber wires to the tops of them,
close the hood.
Hi. The 2006 Kia sorento is not equipped wiht a cabin air filter. Only the 07 and 08 sorentos are equipped wiht this filter. With that said; If your vehicel had a filter, it would be located just behind the glove box. If you were to access it for replacment, you would Open the glove box and remove the side stops so the glove box can swing fully down and hang on its hinges. Once that is done, you will be able to access to the cabin air filter and the clips which hold it in place.
p0454 erratic evap pressure sensor signal
p0122 throttle position sensor circuit low
p0113 intake air temp signal low
p0305 cyl #5 missfire
i would look for a short or open wire somewere
i checked TSBs from kia and none pertain to you
clear codes and drive then check to see if they come back. then repost