Question about 1994 Eagle Talon

1 Answer

1994 rear brake job talon 1.8 front wheel drive

How do u get the piston back in the caliper ? c clamp will not work
also how do u get the rotors off rear? and does anyone know what it means when one side of car brakes r much thinner than other ?
also do u know what size the center rear hub nut is? thanks for any help

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 93 Answers

I can only help with the piston issue. The piston has to be screwed back in. If you go to your local auto parts store they should have a Piston turn in tool.

Posted on Dec 13, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing pads and rotor


Front and back rotors are different. For front rotors, after you remove the wheel you need to remove the bolts holding the caliper to the mounting spindle. The bolt can be a standard 6 face head, a recessed hex, or even a torx or star head recessed bolt.

With bolts removed, the caliper can be worked away from the anti-rattle clips the caliper slides on. These clips are called "hardware" and should be replaced.

The caliper pistons need to be pressed back into position because the new pads are thicker than what you removed. The calipers should be tied and suspended and not allowed to hang by their brake lines while you work with the rotors. Use a "c" clamp and an old brake pad to press the pistons back in. Sometimes it is good to remove the cap on the Master cylinder to allow for brake fluid to travel back to the Master.

Either replace or turn the old rotors and then put the brake hardware in place. Lube the caliper slides. then as a unit position the pads into the caliper and hang the caliper over the rotor. The caliper will hang and pivot into place. Replace and tighten the mounting bolts.

The rear brakes are more of a problem due to a second set of Emergency brakes in rear assemblies. So you have 2 sets of rear brakes, the Emergencies requiring clearance to remove the rear rotors. Some car models require readjustment of the Emergency cables before reassembly.

In all, I would suggest that you be an observer for your first brake job. At least get a Video of the process at a number of autoparts stores. You can wind up with a car you can not drive or reassemble without help.

Nov 11, 2013 | 2008 Mercury Milan

1 Answer

Replace rear brake discs and pads


Depending on vehicle. Find level ground and park there. Put chocks in front and behind wheels not being lifted. Loosen lugs, jack up vehicle, set jack stands, lower vehicle on jack stands, remove lugs and wheel. Open hood remove brake fluid cap. Remove two bolts holding caliper, pull caliper off rotor disc and bracket, remove pads, place a used pad in front of caliper piston, use a c clamp to push caliper piston in caliper, remove c clamp and old pad, hang caliper up, remove 2 bolts holding caliper bracket, remove bracket, remove rotor, install new rotor, install caliper bracket, install new pads, install caliper, repeat this on other side, put cap back on brake fluid tank, remove bleeder fittings and keep pressing brake pedal until an even flow of brake fluid sprays out. Install bleeder fitting. Make sure brake fluid doesnt get on paint and is contained and disposed of correctly, top off fluid install wheels and raise car up remove jack stands, lower car and break in new pads

Nov 06, 2013 | Cars & Trucks

1 Answer

How can I change the rotors and brakes on a 2006 Cadillac?


Front brake
Step 1: Identify Front Disc Brake Components
brake_pads_rotor.jpg
Front Wheel Drive Brake Assembly
Most front disc brake components include: brake rotor, brake pads, brake caliper, caliper mount and brake flex hose. Brake service usual occurs between 20,000 and 40,000 miles depending on driver habits, road conditions and brake pad/ rotor materials used.
Step 2: Remove Brake Caliper to Replace Pads
brake_pad_set.jpg
Removing Brake Caliper Mounting Bolts
Locate primary caliper mounting bolts; apply wrench pressure counter-clockwise (When looking at the head of the bolt) to remove the bolts, upper and lower. Make sure the bolt threads are in good shape and replace if necessary.
Step 3: Remove Front Brake Caliper
remove_brake_caliper.jpg
Remove Front Brake Caliper
After removing the primary caliper mounting bolts lift the brake caliper off of the rotor and then tie or secure to the side, being careful not to bend or kink the brake caliper flex hose. Thoroughly inspect brake caliper and brake hoses for leakage, cracks or chaffing and replace as needed. Next remove the brake pads (If not mounted in the caliper) and secondary caliper mounting bolts. Notice how great protective gloves work, most technicians use them on the job today.
Step 4: Remove Brake Pads
remove_brake_pads.jpg
Remove Front Brake Pads
Once the brake pads have been removed, make sure if there is anti rattle hardware to transfer to the new brake pads. Some brake pad manufacturers will include the proper lube (Caliper slides) and anti-rattle hardware to ensure proper performance of their product.
Step 5: Remove Caliper Mount
remove_brake_pads_holder.jpg
Remove Caliper Mount Bracket
Finish removing secondary caliper mount bolts and remove caliper mount. Note: clean and lube caliper slides and pad friction surfaces of all foreign material or build-up.
Step 6: Remove Brake Rotor
brake_rotor.jpg
Remove Brake Rotor
With the caliper mount out of the way you can now remove the brake rotor. Sometimes it can get stuck so you may need to tap it with a hammer or use penetrating oil to free it up. Some manufacturers use small screws to hold the rotor on as well. Clean and inspect wheel studs, replace if any are damaged. Also clean bearing hub rotor mount surface to ensure the proper mounting of the new brake rotor. Inspect the ABS sensor wheel for cracks or damage and replace as needed.
Step 7: Depressing the Brake Caliper
compress_caliper.jpg
Resetting Brake Caliper
To install the new brake pads you must retract the brake caliper piston. Remove the master cylinder lid or open the brake caliper bleeder screw to allow excess brake fluid to be released if necessary. Install C clamp tool and gently tighten clamp until caliper piston is fully depressed. Note: use old brake pad to protect the caliper piston. Close the bleeders once the piston is retracted completely
Step 8: Installing New Brake Rotor
new_brake_rotor.jpg
Install Brake Rotor
Install new brake rotor, the new rotor is manufactured with a protective film over the rotor to keep it from rusting, remove protective film with brake cleaner before installing; also after the brake job is complete you may experience a small amount of smoke from the rotor when first used. This is normal and will go away after the first couple of uses.
Step 9: Installing New Front Brake Pads
new_brake_pads.jpg
Installing New Brake Pads
Reinstall the front brake caliper mount, and then install front brake pads. Make sure the pads are seated properly in the caliper mount; it must be a close fit to work properly..
Step 10: Reinstall Front Brake Caliper
front_brake_rotor_pads.jpg
Re-Install front Bake Caliper
Reinstall front brake caliper and reinstall caliper-mounting bolts, recheck all mounts and mounting bolts. Check the caliper slides to be sure there is no bind and that the caliper moves freely back and forth on the caliper slides. Bleed brake system per manufacturer's specifications to relieve any air trapped in the system. Before driving the vehicle, push the brake pedal down and let it up slowly, repeat until normal brake pedal operation resumes, this operation is forcing the brake pads to travel to the brake rotors.

Dec 18, 2010 | 2006 Cadillac STS

1 Answer

General directions on how to change the front brakes on a Toyota Supra, 1987.


Buy brake pads.
loosen lugs
Jack car, place on jack stand
turn wheel so front of tire is pointing out.
remove tire
remove caliper (two bolts on back side of caliper
slide caliper off rotor.
(if rotor is damaged, see about having it turned or replaced)
take pads off caliper
open hood and remove cap to mater cylinder reservoir
using special tool (or C-clamp and something to protect piston) push the piston back into the caliper fully.
place new brake pads on caliper.
fit caliper on the rotor
Secure caliper to wheel with bolts
replace wheel
remove jack stand
remove jack
tighten lugs on wheel
replace hubcap
start engine (do not drive yet!!!!!)
pump brake pedal until it tightens up
observe reservoir on master cylinder (fill if needed)
replace cap
pump brakes again
take out for a test drive.

good luck and don't forget to vote!!!

Oct 11, 2010 | 1987 Toyota Supra

2 Answers

How to compress front brske caliper


YOU NEED TO REMOVE 2/3 BRAKE FLUID FROM MASTER CYLINDER.THEN YOU WILL NEED A LARGE C -CLAMP.OPEN C - CLAMP PLACE C - CLAMP OVER TOP BRAKE CALIPER AND AGAINST THE BACK OF THE OUTBOARD BRAKE PAD. THEN TIGHTEN THE C -CLAMP UNTIL THE CALIPER PISTON IS PUSHED INTO THE CALIPER BORE JUST ENOUGH TO SLIDE CALIPER OFF THE ROTOR.WARNING WHEN FINISHING BRAKE JOB.PLACE COVER BACK ON MASTER CYLINDER.TAKE FOOT PUMP BRAKE PEDAL UNTIL YOU GET SOLID BRAKES.THIS SEATS BRAKE SHOES AGAINST THE ROTOR.THEN RECHECK BRAKE FLUID LEVEL IN MASTER CYLINDER.

Jun 16, 2010 | 2005 Chevrolet Uplander

1 Answer

All new brake shoes on 97 jeep front callibers still sticking


The problem lays with the Caliper itself and/or the brake hose connected to the Caliper.
However if you replaced the pads, did you also replace the Rotors or have them Turned? The old pads wear the rotor. New pads on old rotors that have not been replaced or turned may end with rubbing or stuck brakes.
A simple way to test whether it's one and/or the other:
1. Remove the Caliper from the rotor, remove the pads. Keep for now the caliper attached to the brake hose.
2. Very slowly push on the brake, exposing more of the piston out of the bore. Not all the way. Usually until the rubber dust seal/boot is fully extended.
3. Check the seal/boot for cracks and tears, and if clean or not. Bad seals may prevent the piston from re-seating.
4. Using a c-clamp and pushing straight in: Try repushing the Caliper Piston back into the Caliper Bore (the cup back into the hole). It should go back in realitively easy.
5. If it doesn't go back in easy: Again slowly pump the brake and re-push the pistons back out to full extended seal/boot (but not the piston out of the bore).
6. Detached the brake hose from the caliper.
7. Again using a c-clamp and pushing straight in: Try again to repush the caliper piston back into the bore without the hose attached. If it goes back-in relatively easy - the caliper is okay...it is the brake hose.
8. If the caliper piston does not go back in easily - Replace the caliper.
9. When Installing the new (reman) caliper, remember to bleed the brakes.
TRY EITHER OR #10 OR #11 BELOW:
After the new Caliper is reattached to hose and has been bled:
10. Again push on the brake petal to fully extend the caliper piston fully (rubber seal/boot fully extended) Again do not push the piston out of the bore! Try pushing the piston back into the bore. If it does not re-seat relatively easy: Replace the brake hose.
11. Another method: After replacing the new caliper back on the rotor: Assumng the entire front end (2WD front wheel drive) or entire vehicle (2WD rear wheel drive) or (4WD all the time) is jacked up off the ground
a. Put the lug nuts back on the rotor.
b. Have helper Start the vehicle and place in Drive. Don't step on gas!
c. Have then let off the brake and then engage the brake.
d. When they let off the brake watch to see if the Rotor is turning or not, if rubbing or not. Or if still sticking.
e. With a new caliper, turned or new rotors, and still a problem? It is the brake hose!
12. Replace the brake hose and try again.

Another method but more expensive:
OR Replace the calipers, brake hoses; bleed and test!

If this helped or not; or if you need additional help or have addtional questions let me know on fixya.com!

Nov 28, 2009 | 1997 Jeep Grand Cherokee

1 Answer

Brake pad replacement


Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Front wheels
  3. Place a C-clamp over the caliper as illustrated, place a screw drive head against the outboard pad and hook against the rear of the caliper. Slowly tighten the screw drive and retract the caliper pistons into their bores and breaking the outboard brake pad from the caliper fingers.
  4. Once the pad is free, slide the caliper in on the guides to provide clearance between the rotor and inboard pad.
  5. Place an appropriate prytool through the center opening in the top of the caliper behind the inboard pad between the pistons using care not to contact the piston boots. Pry the pad to free it from the pistons.
  6. Remove the two caliper guide pin bolts and position the caliper aside. Remove the brake pads.
ff17c9d.gif
Place a C-clamp over the caliper as illustrated

b802acb.gif
View of the caliper guide pins and boots (1), anti-rattle clips (2), brake rotor (3), outboard pad (4), caliper adapter (5) and inboard pad (6)

To install:
  1. Completely compress the caliper pistons
  2. Install or connect the following:
    • Brake pads with anti-rattle clips onto the adapter
    • Caliper and align the guide pin bolt holes with the guide pins. Install the pin bolts and tighten to 32 ft. lbs. (43 Nm).
    • Banjo bolt with new washers on each side of the hose fitting and tighten to 35 ft. lbs. (47 Nm)
    • Wheels
    • Negative battery cable
  3. Check and adjust the brake system fluid level and road test the vehicle.

Nov 01, 2009 | 2005 Chrysler Pacifica

3 Answers

Need instructions on how to change the front brake pads on a 1994 mazda protege...and i"m a girl so dont assume i know ANYTHING =O)


Ok simple
Place the car in park set the hand brake chock the rear wheels with a brick or a rock so the car does not move.

Now loosen both front tires and lift the car up to a good comfortable working height. Next remove the wheels and set them aside its pretty simple if your just going to replace the brake pads only, You will see something called the caliper it looks like a clamp it will be held on by two screws they can be special screws or simple bolts you remove both of them. now the caliper (clamp) is off there will be a piston that will be pushed very far out you must use brake spreader or very large pliers or a C clamp to push that piston all the way back in. You do this to both sides than once your done with that you will get your new set of brake pads and match them to your old one's make sure there the same and than you install them right where the old one's are with the caliper off. You put it back on over the brake pads clean up the entire area with some brakleen brake parts cleaner. than attatch the caliper with its two bolts and tighten them tight and place the wheels back on the vehicle set it down and remove the jack stands pump up the brakes till there hard BEFORE attempting to drive and that's it your done go for a test drive check over your work 2 times before you set the car down.

Sep 24, 2009 | 1995 Mazda Protege

1 Answer

Need to replace front rotors and brake pads


All you have to do is take off your calipers and the rotor will slide right off. Use a C clamp to push the piston of the caliper back in so you can put your new brakes on.

May 08, 2009 | 1994 Jeep Wrangler

1 Answer

Rear brake to remove replace disk and service due binding


Preliminaries Do 1 wheel at a time Use a jackstand on the wheel you are working on (safety First) Remove the tire on the selected wheel
The Brake caliper is usually held on by 2 bolts. Some of the bolts are Allen wrench type, usually about ¼ inch or 5/16 inch. Remove and the complete brake caliper can be lifted off the rotor. The pads can now be removed. Before installing the new pads you must first return the pad piston to their original position in the caliper. Open the hood of the engine compartment and remove the cover on the master cylinder. This allow the brake fluid to be returned to the master cylinder. To return the pad piston to the original position you will need a C clamp and a flat piece of metal like a small flat file. Put the flat piece of metal on the piston and use the C clamp to put pressure on the piston. Tighten the C clamp slowly and you will see the piston slowly retract into the caliper body. Now you can insert the new pads into the caliper. Mount the caliper over the rotor and reinstall the 2 bolts.

Loringh Hope this helps Good Luck PS Please leave a rating if Appropriate Thanks

Nov 23, 2008 | 2001 Mazda 626

Not finding what you are looking for?
1994 Eagle Talon Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Eagle Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Stewart Dibbs

Level 2 Expert

267 Answers

Are you an Eagle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...