Question about 1995 Pontiac Sunfire

1 Answer

No turn signals, cruise control, or brake lights

A friend was using my car and somehow broke the hazard light switch on top of the steering column. Now I have no hazards, turn signals, cruise control, or brake lights. Not sure what parts I'll need. Any advice?

Posted by on

  • kohnsbaby Dec 12, 2008

    This will also take care of the brake lights?

  • cuddlybear22 Apr 25, 2009

    How do I change my multifunctional switch on a 1995 Sunfire - show diagram

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 116 Answers

Tou need to repl;ace the multi-function switch (turn signal switch) all your lights are run through it
rank my solution & vote 4 me

Posted on Dec 12, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1990 Chevy Suburban v1500. All lights work except for the Brake Lights and Turn Signals. The Blinker switch on steering column is broken, other than that everything is fine.


Yes, the brake light signal on American cars is routed through the turn signal switch. A new switch should restore both your turns and your brake lights.
American cars use the same bulb filament and same wire to the rears for both brakes and turns. Press the brakes when turning and both rear brakes will light, but since one side travels through the flasher relay, that side will blink, while the other side has a steady light.

Apr 06, 2013 | 1990 Chevrolet Suburban

1 Answer

I have a 1996 Ecoline van "Shasta" motorhome. My problem is that the Hazard lights,turn signals,cruise control,and brake lights do not work,all of a sudden. I check all the apropriate fuses and they a


Some vehicles, especially vehicles that use the same lights for brake and turn signal, the brake lights must go through the turn signal switch. If your cruise is on the same switch, I would check your connection under the steering column. If you tilt the column up to get out of the vehicle, you may have unplugged the harness or broken the wires at the tilt point.

Sep 13, 2017 | 1996 Ford Econoline

1 Answer

2000 Chevy Cavalier brake lights


Yes, if your turn signals in the back use the same filaments as the brakes, the multi-switch must allow the brake signal through when the turn signals are not activated. There are multiple diagrams for your system, so I'm not sure what you have. If you have the light blue wire that goes from the brake switch ul the column to the turn switch, make sure it is getting power when the pedal is pressed. It should go thru the switch as shown in the second diagram below.

0996b43f8024327b-zzyiglue2iivran2oy1paayi-5-0.gif

0996b43f8024bcbd-zzyiglue2iivran2oy1paayi-5-2.gif

Jun 30, 2017 | Cars & Trucks

1 Answer

Back brake light stay on, replaced brake switch same problem.Truck has over drive and cruies control If you take switch out of circuit the brake lights stay on the same with the turn/hazard flasher.


Your brake lights and your turn signals go through the multifunction (turn signal) switch. It is common for these switches to short internally. Partial disassembly of the steering column is required to replace it. The airbag stsyem must be disabled, then the airbag removed from the steering wheel. Then the steering wheel must be removed to access the screw in the front of the switch assembly. The rest is pretty easy... a few screws holing the lower cover of the dash, the shroud around the steering column and a few connectors to deal with. (see pictures of switch assembly below)
There are two types of these switches available for 2000 S-10. With cruise control and without cruise control. The one WITHOUT cruise control is much more expensive!


dttech_156.gif
dttech_35.jpg

Aug 06, 2011 | 2000 Chevrolet S-10

1 Answer

I have no signals and when brakes lights are on, lose brake light to either side turn signal is set on


Hi!!

If you activate the turn signal switch and you step on the brake pedal, the turn switch (on the steering column) deactivates the brake light to make the signal light more visible. The bulb for the stop and turn lights is the same.

Turn hazard lights ON. If they don't blink, replace turn/hazard flasher, If one or more lights don't come on, replace bulb.

Check fuse and circuit wiring for broken or loose connections. If all looks fine, check following:

If front turn lights work fine, check brake/turn bulbs.

If turn lights come on but don't blink, replace turn signal/hazard flasher.

If front and back turn lights don't come on, replace switch on column.

Let me know how it worked out, Good Luck

Mar 24, 2010 | 1991 Plymouth Acclaim

2 Answers

Brake light/turn sigs dont work.But lights are on?


Ok, GM had a problem with their hazard light switches in the years of around 2001-2005. These caused some bizarre workings concerning the hazards, lights, turn signals, etc. The circuits overlap, and when the switch malfunctions, it makes for some odd happenings. Normally, when the hazards are on, they cancel out the brake lights and the turn signals, since they use the same circuits. The normal taillights use a different filament in the same bulb, which is why they light up brighter when you press the brakes. The aftermarket has come up with replacement switches in response to these inherent problems, so do not get your switch from GM. Places like RockAuto.com will sell these, though not necessarily this place, it's just the one I use. Usually, GM put these in the steering column, so replacement can be tricky for the average person, as it involves taking apart some of the steering column.

Feb 22, 2010 | 2004 Pontiac Grand Prix

1 Answer

Hazard/turn signal switch


need to replace the whole switch/stick at steering column.

Jun 03, 2009 | 1994 Oldsmobile Cutlass Supreme

2 Answers

1999 oldsmobile alero the traction and cruise not working


use a scanner to check the abs system . most of the time the abs brakes and traction control system work together. your cruise control . unit has a servo motor .in front right fender well. check the fuse and relay also the cruise control brake release switch. and the brake light switch.if all is good you have a cruise control module problems. dealer ship job.

Mar 31, 2009 | 1999 Oldsmobile Alero

Not finding what you are looking for?
1995 Pontiac Sunfire Logo

Related Topics:

239 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8826 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...